Postium PRM-902A Manuale utente

LCDRacksMonitor

PRM-902A

MULTI-CHANNEL LCD MONITOR

Contents

Warnings .......................................................................................................... 3

Features ............................................................................................................ 4

Name & Function of Each Part ......................................................................... 5

OSD Menu Organization & Adjustment ........................................................... 8

Other Functions .............................................................................................. 15

System Default Value...................................................................................... 24

Specifications ................................................................................................. 25

13."

Warning

MULTI-CHANNEL LCD RACK MONITORS

Warning

· Always use DC 12V power.

· If liquid comes in contact with this product, please disconnect the product immediately

and seek professional support before continued use.

· Keep unit disconnected during extended periods of nonuse.

Keep unit well-ventilated to prevent overheating.

Do not install the product near any heat-generating equipment. Also, keep the product

out of direct sunlight or dusty areas.

Clean the product with a noncommercial, mild detergents only.

When transporting the product, make use of its original packaging for safer carriage.

FCC (Federal Communications Commission)

This equipment has been tested and found to comply with the limits for class A digital device, pursuant to

part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment. This equipment generates,

uses, and can radiate radio frequency energy, and if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications. Operation of this equipment

in a residential area is likely to cause harmful interference in which case the user will be required to correct

the interference at his own expense.

Warning!! : Changes or modifications not expressly approved by the manufacturer could void the

user’s authority to operate the equipment.

Disposal of Old Electrical & Electronic Equipment

(Applicable in the European Union and other European countries

with separate collection systems)

This symbol on the product or on its packing indicates that this product shall not be treated as household

waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and

electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential

negative consequence for the environment and human health, which could otherwise be caused by

inappropriate waste handling of this product. The recycling of materials will help to conserve natural

resources.

Features

PRM Series LCD Rack Monitors have the following features:

· Compatible with varied SDI Signals

The product is compatible with varied SDI signal

- 480i, 576i, 720p, 1035i, 1080i, 1080p, 1080psf, 2K

· Compatible with varied Analog Signals

The product is compatible with varied Composite, S-Video signal

- NTSC, PAL, SECAM

The product is compatible with varied Component, RGB signal

- 480i,576i,480p,576p,720p,1080i,1080p

· Waveform/Vector Scope/Audio Level Meter

“Y”, “Cb”, “Cr” Waveform & Vector Scope available for SDI Signals

16-CH Embedded Audio Level Meter

· Audio Out

Built in Audio De-embedder and Internal Speakers

Stereo Audio out using phone jack

· Knob Control

Easy to adjust user configuration using the control knob

· BLUE & MONO

· H/V Delay

· Wide Variety of Markers & Safety Areas

Center Marker, Safety Area Marker, Aspect Marker, Display Size(Scan)

· Pixel To Pixel

Provides both full screen and unscaled native image.

· Wide Screen / LED Backlight (902Q/702A/702Q), CCFT Backlight (902A)

· 24Bit RGB LVDS Interface Panel

· DC Compatible

The product is powered by normal 12V source.

· Remote Control Function

Simple remote controllability with single cable connection,

no additional modules required

· Additional Features

Active Loop Through/SDI,

902A - 600:1 contrast ratio, 600 cd/m brightness

902Q - 1000:1 contrast ratio, 400 cd/m brightness

702A - 700:1 contrast ratio, 350 cd/m brightness

702Q - 800:1 contrast ratio, 400 cd/m brightness

OSD user interface, Rack Mountable

13."

Name & Function of Each Part

· [BRIGHT] knob

Used to adjust the degree of brightness between MAX(25) and MIN(-25).

· [CONTRAST] knob

Used to adjust the contrast ration between MAX(25) and MIN(-25).

· [CHROMA] knob

Used to adjust the saturation between MAX(25) and MIN(-25).

· [VOLUME] knob

Used to adjust the volume between MAX(20) and MIN(0).

· [SDI-A] button

Used to select SDI A Input.

· [SDI-B] button

Used to select SDI B Input.

· [ANALOG] button

Used to select desired Analog Input (CVBS1/2/3, S-Video, Component, RGB).

<FRONT>

~h}lmvyt

is|lGMG tvuv

thyrly

zjhu

{hss

iypno{ulzz

jvu{yhz{

joyvth

}vs|tl

zkpTh

zkpTi

huhsvn

kv~u

tlu|

lu{ly

hUGsl}lsGtl{ly

o}Gklsh

hzwlj{

slk

wv~ly

PRM-902A

MULTI-CHANNEL LCD RACK MONITORS

Name & Function of Each Part

]

· [SCAN] button

Used to transfer from OVER SCAN mode to ZERO SCAN mode.

Mode changes in the order of ZERO SCAN -> OVER SCAN -> PIXEL TO PIXEL

-> ZERO SCAN.

-This function is not available in Internal Pattern and Wave Form/Vector Scope full size.

· [ASPECT] button

Used to toggle aspect ratio in SD from standard to anamorphic.

- This function is not available in Internal Pattern and Wave Form/Vector Scope full size.

· [MARKER] button

Used to show MARKER on the screen. The type of marker at work may be selected

on the main menu.

- This function is not available in Internal Pattern, Wave Form/Vector Scope full size,

Pixel to Pixel and HV Delay mode.

· [HVDELAY] button

Used to activate the HV Delay mode.

- This function is not available in Internal Pattern and Wave Form/Vector Scope full size.

· [BLUE/MONO] button

You may remove R(red) and G(green) from the input signal and play the screen only with

B(blue) signal. Button may be pressed twice to change the screen to MONO mode.

(This mode uses only Luminance value)

- This function is not available in Internal Pattern and Wave Form/Vector Scope full size.

· [AUDIO LEVEL] button

Used to active AUDIO LEVEL METER on the screen. Able to select type of Audio Level Meter in order

of Off / Horizontal / Vertical / dBFS / BBC / EBU / VU / Nordic

The type of audio level meter at work may be selected on the main menu.

- This is available only in SDI input mode.

· [WAVE/VECTOR] button

Used to activate the Waveform or Vector Scope.

Small and Full Waveform/Vector Scope display can be selected in the system menu.

Small display : YCbCr ˧Y ˧Cb ˧Cr ˧Vector ˧off

Full display : Y ˧Cb ˧Cr ˧Vector ˧off

(Use “WAVE/VECTOR” button to control)

- This is available only in SDI input mode.

· [UP] button

Used to navigate menu during OSD menu activation. It may also be used to toggle

clockwise through 1:1 quadrants in native scan mode.

· [DOWN] button

Used to navigate menu during OSD menu activation. It may also be used to toggle

counterclockwise through 1:1 quadrants in native scan mode.

· [MENU] button

Used to activate the OSD menu.

· [ENTER] button

Used to confirm a chosen value (or mode) within the OSD menu.

- This can be used to control the position of Wave/Vector in small size.

· [POWER] button

Power On/Off button.

If the signal is normal, LED lights in Green. If the signal is unsupported or disconnected,

LED flashes in Yellow.

· TALLY

LED indicating monitor’s current status using optional Remote.

13."

Name & Function of Each Part

· SDI A-IN (BNC)

SDI A signal input terminal

· SDI B-IN (BNC)

SDI B signal input terminal

· SDI-OUT (BNC)

SDI signal output terminal

· CVBS1/B/Pb (BNC)

Signal input terminal used for COMPOSITE1, RGB B, COMPONENT Pb signals.

· CVBS2/G/Y/S-Y (BNC)

Signal input terminal used for COMPOSITE2, RGB G, COMPONENT Y, SVIDEO Y signals.

· CVBS3/R/Pr/S-C (BNC)

Signal input terminal used for COMPOSITE3, RGB R, COMPONENT Pr, SVIDEO C signals.

· AUDIO OUT (phone jack)

Used to audio output jack.

· FACTORY PGM (15 pins)

Input connector for FACTORY PGM

allowing for firmware update.

· REMOTE (RJ-45)

Connection for remote control of monitor.

j j j yni zT}

Xj}izXw iuGjU

Yj}izY  n 

Zj}izZw y j

<REAR>

kjGpuG

XaGnu k

[aGRXY}

[

PRM-902A

zkpGv|{w|{

zkpGiGpuw|{

zkpGhGpuw|{

yltv{l

mhj{vyG w nt

j}izXViVw

j}izYVnVVzT

j}izZVyVwVzTj

kjGpu

h|kpvG v|{

MULTI-CHANNEL LCD RACK MONITORS

OSD Menu Organization & Adjustment

[1] MAIN - Picture

· Brightness

This Item controls the degree of brightness.

-Brightness can be adjusted by using the [BRIGHT] control knob on the front of the monitor.

· Contrast

This item controls the contrast ratio.

-Contrast can be adjusted by using the [CONTRAST] control knob on the front of the monitor.

· Chroma

This item controls saturation.

-Saturation can be adjusted by using the [CHROMA] control knob on the front of the monitor.

· Aperture

This item controls the picture sharpness.

· Phase

This item controls Phase value (Hue).

-This function is only available in Composite and S-Video NTSC Input.

· NTSC Setup

This item sets IRE value in NTSC mode between 0 IRE and 7.5 IRE.

-This function is only available in NTSC Input.

13."

OSD Menu Organization & Adjustment

[2] MAIN - Color

· Color Temp

This item controls Color Temperature with presets of 3200K, 5600K, 6500K, 9300K, and User1,

User2 & User3 mode.

· User

On User Mode, the user may select and control R, G, & B GAIN, BIAS values by using

the [UP]/[DOWN]/[ENTER] buttons.

· Color Copy

In User mode, user can copy the preset of 3200K, 5600K, 6500K or 9300K to make

the custom adjustment by using the [UP]/[DOWN]/[ENTER] button.

[3] MAIN - Marker

· Line Marker

This selects the marker type when the MARKER is displayed on the screen.

Compatible MARKER types are as follows:

tvkl thyrlyGjshzz

okGVGzkGX]a` X]a`SG [aZSG [aZG vuGhpySG X\a`SG X[a`SG XZa`SG XU_\aXSG YUZ\aXSG XU_\aXG MG [aZ

zkG[aZ X]a`

MULTI-CHANNEL LCD RACK MONITORS

Indice

Altri manuali Postium Monitor

Manuali Monitor popolari di altre marche

Linear Acoustic

Linear Acoustic LQ-1000 Manuale utente

AOC

AOC I2579V Manuale utente

Gateway

Gateway FPD1520 Manuale utente

Furuno

Furuno Mu 120c Manuale utente

Asus

Asus VB171D - 17" LCD Monitor Manuale utente

Dell

Dell S2230MX Istruzioni utente

Philips

Philips 107C64 Manuale utente

Dell

Dell S2409WFP Manuale utente

EverFocus

EverFocus EN-7517E Manuale utente

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manuale utente

Dell

Dell Precision 7680 Manuale di istruzioni

LG 50PM1M - - 50" Plasma Panel Manuale utente

Bosch

Bosch DDU 9 Manuale utente

Acer

Acer A231HL Manuale utente

Philips

Philips 86BDL4152T Manuale utente

NEC

NEC AccuSync LCD5V Manuale utente

Emay

Emay SleepO2 Manuale utente

IBM

IBM 6360 Istruzioni per l'installazione