OWNERS MANUAL
All information contained in this owner manual is the property of
Power Arc Ignitions Co., Inc. and cannot be duplicated in whole or
in part by any means or disseminated or distributed without the
prior written consent of P. A. Ignitions Co., Inc. The information in
this manual has been carefully compiled and checked for
accuracy and is believed to be correct. However, P. A. Ignition
Co., accepts no responsibility for inaccuracies which may occur.
All specifications in this manual are subject to change without
notice.
Power Arc Ignitions Co., Inc.
2518 N.E. 102 Ave.
Ankeny, IA 50021
(515) 964-7608
The following customer actions automatically voids the warranty.
1) Use of any other spark plug wires other than resistor type
wires with at least 800 ohms of resistance. 2) Use of non-resistor
spark plugs. 3) Drilling or cutting of any kind into the module 4)
Incorrect wiring of the module. 5) Use of module on systems with
defective charging systems. 6) Use of defective or incorrect coils
7) Directly shorting the coil output wires to +12 VDC. 8) Physical
damage to the ignition . 9) Any other items covered in the
warranty & instruction manual.
LIMITED WARRANTY
Power Arc Ignition Co., Inc. warrants to the original retail
purchaser of a Power Arc IDS ignition that it will, free of charge,
repair or replace at its own option, the product if returned to
Power Arc Ignition Co., Inc. within 6 months after purchase and if
found by Power Arc Ignition Co., Inc. to be defective in material or
workmanship. This warranty is not transferable by the purchaser
and shall be voided: if alterations not authorized by Power Arc
Ignition Co., Inc. are made in the equipment or if the serial
number or date of manufacture has been altered, defaced or
removed. Nor does this warranty apply: if the equipment has
been subjected to accident, misuse, improper hookup, damaged
by flood, fire, or act of God, or has been used on circuits or
voltages other than those indicated in its instruction manual. If
the equipment is found to be defective in materials or
workmanship the equipment will be returned and Power Arc
Ignition Co., Inc. will pay the return shipping (this does not include
next day shipping, second day shipping, shipments outside of the
continental U. S. A. or shipments outside of the U.S.A.). All
warranty work outside of the U.S.A. must include prepayment of
return shipping. Customs, duties or tariffs are not covered by this
warranty. If the equipment is found to be defective but is due to
customer misuse (as described in warranty) Power Arc Ignition
Co., Inc. will notify the customer and if the customer wants the
defective equipment returned Power Arc Ignition Co., Inc. will
return the equipment C.O.D. freight. If the equipment is found to
be in operational order when returned to the factory Power Arc
Ignition Co., Inc. will return the module with a $30.00 service
charge plus freight and C.O.D. Charges. Any module returned
under the warranty must include note of explanation of failure and
be accompanied by a dated bill of sale. Power Arc Ignition Co.,
Inc. warranty obligations are limited to those set forth herein and
no other obligations, expressed or implied, are assumed by
Power Arc Ignitions Co., Inc. Some states do not allow the
exclusions or limitations of incidental or consequential damages,
or allow limitations on how long an implied warranty lasts, so the
above limitations or exclusions may no apply to you. This
warranty gives you specific legal rights, and you may also have
other rights which vary from state to state.
SPARK PLUG WIRES
Choice of spark plug wires is an important consideration when
using an electronic ignition system. Use ONLY Resistor
(CARBON CORE) or Approved Spiral Wound Spark Plug
Wires& Resistor Spark Plugs. Solid or Spiral unapproved
spiral wound wires will damage the ignition module and
void the warranty!
SPARK PLUGS
You must use a resistor spark plug with electronic ignitions.
Spark plug gap should be limited to as small as possible, while
still maintaining performance.
A wide spark plug gap can cause the following problems: Hard
cold starting, misfires during rich or lean fuel conditions, and
reduction of upper rpm range.
Initial settings for spark plug gaps are:
Spark plug Multi-Spark 0.025-0.032
The higher the engine compression, the
more voltage required to fire the plug, and the narrower the plug
gap should be.
The higher the rpm's the less time the coil has to charge
to break over voltage or complete saturation. A narrower spark
plug gap will help high rpm stability.
To maintain a good secondary spark within a
wider rpm range it is wise to run a narrower spark plug gap. It is
better to precisely place two stable, consistent sparks than to fire
one wider spark that may cause misfires in rich or lean
conditions, or from any of the above reasons.
Many things effect spark plug gap settings:
Multi-Spark:
Compression Ratio:
RPM:
Encoder (rotor) Installation and Cam end play
Cam end play should not exceed 0.020”. The encoder disk
should be fall the constraints of the optical pickup triggers.
Optical
Pickup Timing
LED
Encoder
Adapter
Optical Encoder Disk can not strke the Ignition Module
or Optical Pickup at anytime during operation. Cam
walk is normally outward so position Encoder Disk
appropriately using shim washers.
Tighten applying to threads pink Loctite.
LocTite 222MS threadlocker for small fasteners to 1/4"
�
�
�
�
�
�
�
�
�
�
�
�
No External Module (All in the Points Housing)
Low Voltage Operation (down to 6 Volts)
Uses less Energy than Points
4 Timing Maps with Select Wire
Multi-Spark 3 Sparks / Compression Stroke
Crank Operation Sensing
Automatic Coil Safety Shutoff
Precision Rev limiter
Static Timing Light
Stainless Steel Encoder Disk
Electronic Tach Output (2 cylinder tach output)
POWER ARC IGNITIONS CO., INC.
2518 N. E. 102 AVE.
ANKENY, IA 50021
(515) 964-7608
http://www.powerarc.com
PATENT #4,951,629 OTHER PATENTS PENDING
CD2LM for
Kawasaki KZ Twins
CD2-LM IgnitionSystem
Blue Sensor
Brown Sensor
TIMING
LIGHT
T
A
C
H
Blue and Brown wires
must be hooked to
(-) Negative if not used.
Orange, Coil Trigger
