Power bass OE692-FD Guida utente
FORD & LINCOLN O.E.M. PLUG & PLAY
Application Guide
Please read through this manual to familiarize yourself with your new speakers. Should your PowerBass
Autosound speaker components ever require service, you will need to have the original dated receipt.
OE692-FD
OE652-FD
OE69C-FD
OE65C-FD
Thank you and Congratulations
Congratulations on your purchase of PowerBass Autosound speakers.You now own a speaker of uncompromising
design and engineering from a factory that truly believes in the relentless pursuit of perfection. Incorporating the
highest quality parts and state-of-the-art materials, these speakers display the ultimate balance between
high fidelity, performance and long-lasting reliability.
At PowerBass USA, Inc. we are confident you will have many years of outstanding enjoyment from this
great Component Speaker investment. For maximum performance we recommend that you have your new
PowerBass Autosound product installed by an Authorized PowerBass Autosound Dealer.
To learn more about PowerBass, please visit us on the World Wide Web at
http://www.powerbassusa.com
∆Warning ∆
Continuous exposure to sound pressure levels in excess of 100 dB can cause permanent hearing loss. PowerBass Autosound Speakers
are capable of producing sound pressure levels well over 170 dB. Please observe all local sound ordinances while listening to your
PowerBass Autosound system. PowerBass USA, Inc. accepts no liability for hearing loss, bodily injury, or property damage due to the
result of use or misuse of this product.
3
POWERBASS FORD OEM Plug & Play FEATURES
- Injection PP Cone
- Nylon OEM Speaker Basket
- 1” Silk Dome Tweeter on Coaxials (OE652-FD, OE692-FD)
- 1” Silk Dome Tweeter with Diffuser on Components Kits (OE65C-TY, OE69C-TY)
- 20 oz. Magnet (OE652-FD, OE65C-FD) 35 oz. Magnet (OE692-FD, OE69C-FD)
Fig 1
The A Pillars
Fig 2
Connector for Tweeter
Fig 3
Tweeter
Fig 4
Speaker Extension Cable
4
SPECIFICATIONS
(Due to Constant Improvements, Specifications and Parameters are subject to change without notice.)
Model # Size Nominal
Impedance
Frequency
Response
Sensitivity
1W/1M
Magnet Size Mounting
Depth
Power RMS/
Peak
OE692-FD 6x9” 4-ohm 65Hz - 20kHz 89 dB 35 oz. 1.85” 80W/160W
OE652-FD 6.5” 4-ohm 70Hz - 20kHz 88 dB 20 oz. 1.6” 60W/120W
OE69C-FD 6x9” 4-ohm 65Hz - 20kHz 89 dB 35 oz. 1.85” 80W/160W
OE65C-FD 6.5” 4-ohm 70Hz - 20kHz 88 dB 20 oz. 1.6 ” 60W/120W
Before beginning your installation, thoroughly read this guide and keep it as a reference. It
will give you tips on proper placement, wiring, and installation as well as how to obtain the
best sound from the PowerBass speakers you have selected.
COMPONENT SILK DOME TWEETER SPECIFICATIONS
DOME
SIZE
NOMINAL
IMPEDANCE
FREQUENCY
RESPONE
SENSITIVITY
(1M / 1M)
POWER
(RMS/PEAK)
1” Silk Dome 4Ω3K-20Khz 91 dB 45/90
Tweeter
Woofer
5
INSTALLATION EXPERIENCE
Installation of PowerBass Autosound Speakers requires experience with a variety of mechanical and electrical
procedures. This manual only provides general installation and operation instructions. If you have any reserva-
tions about your installation skills or lack of the proper tools, please contact your local PowerBass Autosound
dealer for assistance.
TIPS TO GET THE MOST OUT
OF YOUR POWERBASS SYSTEM
Your PowerBass Autosound speakers have been meticulously engineered and designed to handle high power
musical reproduction. Despite their rugged construction, it is possible to damage your speaker if they are
improperly used. In general, you will hear distortion as a so-called warning before any damage occurs. If
you hear distortion in your system, immediately reduce the musical level to the point where the sound retains
its clarity.
1. Be sure you supply the speakers with enough unclipped amplifier power to drive them properly. (More
damage can be done to a speaker by under-powering and clipping your amplifier than any other
way!)
2. Where possible, a separate amplifier just for your speaker should be used with an electronic crossover to
set the frequency range.
3. When connecting speaker wires from the amplifier or head unit to that of the speaker itself, pay attention
to the polarity of the connection. This will insure optimum sound reproduction and performance.
PREPARING FOR INSTALLATION
NOTE: The tools listed below may be required for proper installation.
• An electric drill with drill bits
• Phillips-head and standard screwdrivers
• 7mm Socket
• Panel Removal Tools
6
INSTALLATION PRECAUTIONS
NOTE: Proceed only if you are a qualified installer otherwise; let your dealer do it.
• Always wear protective eyewear when using tools.
• Turn off all stereo and other electrical devices before you begin.
• Disconnect the (-) negative lead from your vehicle’s battery.
• Keep the speakers in the package until nal installation.
COMPONENT SYSTEM INSTALLATION
7
Fig 6
6X9” SPEAKER INSTALL (OE692-FD, OE69C-FD)
1. After removing the door panel, unplug speaker plug
from factory speaker.
5. Fit speaker in place and make sure all mounting holes
line up. Install with the four 4 x 7mm screws you removed
from the factory speaker.
3. Remove factory speaker.
2. To remove the factory speaker unscrew the 4 x 7mm
screws (do not discard these screws you will need them to
install your new speaker).
6. Now plug the factory speaker plug into the new speak-
er. If the factory plug is not long enough try to remove
some of the tape on the wire to extend it or use the sup-
plied extension cable (see Fig 4, pg 4). Reinstall door panel
afterwards.
4. Now you’re ready to install your new speaker.
8
1. After removing the door panel, unplug speaker plug
from factory speaker.
5. Now plug the factory speaker plug into the new speaker.
If the factory plug is not long enough try to remove some of
the tape on the wire to extend it or use the supplied exten-
sion cable (see Fig 4, pg 4). Reinstall door panel.
3. Remove factory speaker. Now you’re ready to install
your new speaker.
2. To remove the factory speaker, unscrew the 3 x 7mm
bolts (do not discard these screws you will need them to
install your new speaker)
4. Fit speaker in place and make sure all mounting holes
line up. Install with the 3 x 7mm screws you removed from
the factory speaker.
6.5” SPEAKER INSTALL (OE652-FD, OE65C-FD)
9
1. Remove door panel or unclip tweeter cover/housing to
gain access to the factory tweeter.
5. Plug your new tweeter into the factory plug and re-
install door panel or tweeter cover/housing.
3. Now clip-in your new tweeter making sure it’s aligned
correctly and fully secure.
2. Unclip the factory tweeter from its housing.
4. Locate the 2-pin tweeter adapter plug and connect
it to your new tweeter (Fig 2), making sure the polarity
is correct.
DOOR TWEETER INSTALL (OE69C-FD, OE65C-FD)
10
Questo manuale è adatto per i seguenti modelli
3
Indice
Altri manuali Power bass Impianto stereo
