Powerplay KSP1221 Manuale utente
OWNER’S MANUAL
5 Piece Drumset
PLEASE READ BEFORE OPERATING THIS EQUIPMENT
Model: KSP1221
1
1. Snare Drum
2. Snare Throw ff
3. Bass Drum Tension Rods
4. Bass Drum Spurs
5. Drumsticks
6. Cymbal
7. Cymbal Rod
8. Drum Key
9. Lug Casing
10. “L” Mounting Rod for Tom Drum
11. Tom Drum
12. “L” Mounting Rod for Snare Drum
13. Bass Drum Hoop
14. Drum Throne Stool
15. Bass Drum Head
16. Bass Drum Beater
17. Bass Drum Pedal
LOCATION OF CONT OLS
4
5
1
2
3
16
15
13
17
14
12
11
10
9
8
6
7
2
Please make sure you have all of the following items included before beginning assembly:
D UM CONTENTS
DRUMS
(A) Bass (B) Snare (C) Tom
CYMBAL AND DRUM UNASSEMBLED PARTS
(D) Cymbal (E) Bass Hoops (2) (F) Bass Heads (2)
(G) Bass Tension Rods (8)
3
D UM CONTENTS (CONTINUED)
STANDS AND HARDWARE
(I) “L” Mounting Rods (2) (J) Cymbal Rod (K) Bass Drum Pedal
(L) Bass Drum Spurs (2) (M) Drum Sticks (2) (N) Drum Key
THRONE
(O) Throne Pad (P) Throne Stand
1. Place the Bass Drum (A) on a soft, flat surface.
Insert the two Bass Drum Spurs (L) into the spur
mounts at the 4 o’clock and 8 o’clock positions as
shown in Figure 1 and tighten.
2. See Figure 2 for this step. Place a Bass Drum
Head (F) over the rim of the Bass Drum (A) and
cover with a Bass Drum Hoop (E). Make sure the
logo aligns straight when the Bass Drum is
assembled. Thread a tension Rod (G) through the
Bass Drum Hoop (E), then screw the Bass Drum
Tension Rod (G) into the lug casing on the Bass
Drum so it is secure, but not tight.
Repeat this step with the three additional Bass
Drum Tension Rods (G), applying equal amount of
pressure for each.
When all Bass Drum Tension Rods(G) are secure,
tighten each evenly until the Bass Drum Head (F)
is smooth and slightly tight. It is recommended
tightening the first lug, then tightening the lug on
the opposite side for best tuning.
3. Turn over the Bass Drum and repeat step 3.
4. Stand the Bass Drum on its side with the
Bass Drum Spurs (L) on the bottom. The
Bass Drum Spurs (L) should extend out
from the drum just enough to brace it on
the floor and are located at the front half of
the Bass Drum.
4
INSTALLATION (MAIN D UM ASSEMBLY)
efer to the Location Of Controls on page 1 and to the Drum Contents on page 2.
NOTE: The bass drum need to be assembled; while
the Snare and Tom Drum are assembled already.
Figure 1
Figure 2
Figure 3
5. Facing the back of the Bass Drum
insert two “L” Mounting Rods (I)
into the closest two mounting
brackets on the top of the Bass
Drum as shown in Figure 4. The
first “L” Mounting Rod (I) should
point to the left and the second
should point to the right. Tighten
the nut on each mounting bracket.
6. Place the Snare Drum (B) on the
“L” Mounting Rod (I) pointing to
the left. Place the Tom Drum (C)
on the “L” Mounting Rod (I)
pointing to the right. Adjust the
Snare Drum and Tom Drum to
comfortable playing positions.
7. Remove the wing nut and the top felt on the Cymbal Rod (J) and place the Cymbal
(D) on the Cymbal Rod (J). Replace top felt and then wing nut. Tighten the wing nut,
but allow the Cymbal to be slightly loose so it will sustain properly.
8. Insert the Cymbal Rod (J) into the remaining mounting bracket on the top of the
Bass Drum. Position the Cymbal higher that the Tom Drum and in a comfortable
playing position.
TUNING THE D UM USING THE D UM KEY
(See Figure 5):
1. Use the Drum Key to tighten/loosen the screws
on the drums. Also use to tune the sound of the
drum.
5
INSTALLATION (MAIN D UM ASSEMBLY) - CONTINUED
Figure 4
Figure 5
1. Locate the round headed bolt,
wing nut and washer. Position the
pole to the desired height and
insert the round headed bolt into
the hole as shown in Figure 6.
Insert the washer, followed by the
wing nut and tighten.
2. Place the pole from step 1 into the
FULLY EXTENDED tripod so the
bolt fits into the cutaway in the
tripod pole as shown in Figure 7.
Tighten the wing nut.
3. Locate the seat, hex bolt and wing nut washer. Also
locate the Seat Collar on the seat, as shown in
Figure 8. Place the seat over the middle pole. Slide
the hex bolt (which is used to adjust the height of
the seat) through the seat collar and the pole, then
lock in place with the wing nut and washer.
4. Figure 9 shows an illustration of the Drum Seat N T EXTENDED. Figure 10 shows
the Drum Seat EXTENDED. Bottom retainers are all the way down and locked in
place. Check the tightness of the bolts.
5. ENJ Y Y UR NEW DRUMS.
6
INSTALLATION (D UM SEAT ASSEMBLY)
Middle pole
Hex bolt
Wing nut
Figure 6 Figure 7
Seat Collar
Figure 8
Figure 9 Figure 10
Printed in China KSP1221-IB-E0GJ1-A0 S
Indice
