PowerShield Centurion Pro Series Manuale utente

USER MANUAL

Centurion Pro Three Phase UPS

powershield.com.au

3 Phase In 3 Phase Out, 415 V (Dual Input)

10kVA Standard 10kVA Long Run

20kVA Standard 20kVA Long Run

30kVA Standard 30kVA Long Run

40kVA Standard 40kVA Long Run

60kVA Long Run (only)

80kVA Long Run (only)

3 Phase In 1 Phase Out, 415 V (Dual Input)

10kVA Standard 10kVA Long Run

20kVA Standard 20kVA Long Run

TABLE OF CONTENTS

1 SAFETY AND EMC INSTRUCTIONS 4

1.1 Transportation and storage 4

1.2 Preparation 4

1.3 Installation 4

1.4 Connection Warnings 5

1.5 Operation 6

1.6 Standards 6

2 INSTALLATION AND OPERATION 7

2.1 Unpacking and Inspection 7

2.2 Wiring Terminal View 8

2.3 Schedule of Components 10

2.4 Single UPS Installation 10

2.5 Speciﬁcations 3:3 415V 11

2.6 Speciﬁcations 3:1 415V/240V 13

2.7 Terminal Block Diagrams 15

2.8 UPS Installation for Parallel System 19

2.9 Software Installation 22

3 INTEGRATION WITH MBP 22

4 COMMISSIONING 23

5 WARRANTY 23

6 OPERATIONS 24

6.1 Button Operation 24

6.2 Screen Description 24

6.3 Audible Alarm 58

6.4 Single UPS Operation 58

6.5 Parallel Operation 61

6.6 Fault Code 63

6.7 Warning Code 64

7 TROUBLE SHOOTING 65

8 STORAGE AND MAINTENANCE 66

8.1 Storage 66

8.2 Maintenance 66

9 SPECIFICATIONS 68

WARNING

Before energizing the UPS, please take the time

to read and understand

• all of the safety information

• all of the warnings

• all of the operating instructions.

It is highly recommended to have this UPS

commissioned by a Powershield Service Partner.

This equipment should only be serviced and

maintained by qualiﬁed PowerShield Service

Partners. Failure to use a qualiﬁed service

partner may impact your warranty.

All electrical work must be undertaken by

qualiﬁed electricians.

Disclaimer

We assume no responsibility or liability for

loss or damages, whether direct, indirect,

consequential or incidental, which might arise

out of the use of this manual. Information in

this manual is subject to change without notice.

If you ﬁnd information in this manual that is

incorrect, misleading, or incomplete, we would

appreciate your comments and suggestions.

1 SAFETY AND EMC INSTRUCTIONS

All safety instructions in this document must be read, understood, and followed.

1.1 Transportation and Storage

• Please transport the UPS system only in the original packaging to protect against shock

and damage.

• The UPS must be stored in a facility where the temperature is well regulated. Ambient

temperatures should be between 0–40°C and relative humidity shall be 0–95%

non-condensing.

• Any storage of greater than 30 days refer to section 8 for more detail.

1.2 Preparation

• Condensation may form if the UPS system is moved immediately from cold to warm

environment. The UPS system must be dry before being installed. Please allow at least two

hours for the UPS system to acclimatise to the environment prior to energisation.

• If the UPS might be exposed to temperatures over 40°C, please contact PowerShield for

further advise.

• Do not install the UPS where the relative humidity exceeds 95%, and it must also be non-

condensing.

• Do not install the UPS near bodies of water or salt water. (conformal coating may be

required to protect your UPS)

• Do not install the UPS in high dust, conductive dust environments (conformal coating may

be required to protect your UPS)

• Do not install the UPS system where it would be exposed to direct sunlight or nearby heat

source.

• Do not block ventilation holes on the UPS housing.

1.3 Installation

• Do not connect appliances or devices which would overload the UPS

Care needs to be taken with motor start loads, or other load with high in rush to size

the UPS accordingly.

• The UPS requires 50cm front, side, and rear access for maintenance and airﬂow.

• The UPS and any supplied battery cabinets come with an earth connection. Please ensure

all earth connections are installed and tested in accordance with AS/NZS 3000 and or local

regulations.

• All electrical work shall be undertaken by a qualiﬁed electrician (in your local jurisdiction)

• All commissioning / start-up shall be undertaken by either PowerShield or a locally trained

service technician.

• All ongoing maintenance shall be undertaken by qualiﬁed personal. PowerShield

recommends that all maintenance work is undertaken by a PowerShield trained service

technician, to ensure that the vendor warranty is maintained.

• All cabling, breakers, isolators and the like shall be sized and installed in accordance with

this manual and AS/NZS 3000 (suite of standards) or local equivalent, to protect both

upstream and downstream of this UPS.

1 SAFETY AND EMC INSTRUCTIONS continued

• All cabling prior to energisation shall be tested in accordance with AS/NZS 3000 or local

equivalent, the test result shall be made available to PowerShield or PowerShield service

agent upon request. This includes a phase rotation test for three phase product.

• Secure the grounding/earthing wire before connecting to any live wire terminal.

1.4 Connection Warnings

• Back feed protection has been already provided in accordance with EN-IEC 62040-1, inside

of the UPS. No additional back feed protection is required to be installed.

• This UPS should be connected with TN grounding/earthing system.

• The power input for this unit must be three-phase rated in accordance with the equipment

nameplate. It also must be suitably grounded.

WARNING:

HIGH LEAKAGE CURRENT

EARTH CONNECTION ESSENTIAL

BEFORE CONNECTING SUPPLY

• Use of this equipment in medical instrument of any life-sustaining equipment where failure

of this equipment can reasonably be expected to cause the failure of the life-sustaining

equipment or to signiﬁcantly affect its safety or effectiveness is not recommended.

Do not use this equipment in the presence of a ﬂammable mixture with air, oxygen or

nitrous oxide.

• Connect grounding terminal of UPS to a grounding electrode conductor. The ground

conduct should be tested prior to energisation of the UPS.

• Warning labels should be placed on all primary power switches installed in places away

from the unit to alert the electrical maintenance personnel of the presence of a UPS in the

circuit. The label will bear the following or an equivalent text:

BEFORE WORKING ON THIS CIRCUIT:

• Isolate Uninterruptible Power Supply (UPS)

• Isolate the batteries (internal or external)

• Then check for Hazardous Voltage between all terminals including the protected earth

RISK OF HIGH VOLTAGE

1 SAFETY AND EMC INSTRUCTIONS continued

1.5 Operation

• Do not disconnect the grounding/earthing conductor cable on the UPS or the building

wiring terminals under any circumstance.

• The UPS system features its own, current source (batteries).The UPS output terminal blocks

may be electrically live even if the UPS system is not connected to the building mains/live

cables.

• In order to fully disconnect the UPS system, ﬁrst press the ‘OFF’ button, isolate all batteries

(internal and or external) and then disconnect the electrical cabling.

• Ensure that no foreign objects can enter the UPS.

• The UPS should only be operated by individuals that are familiar with operating UPS(s).

1.6 Standards

Safety

IEC/EN 62040-1

EMI

Conducted Emission :IEC/EN 62040-2 Category C3

Radiated Emission :IEC/EN 62040-2 Category C3

EMS

ESD :IEC/EN 61000-4-2 CD Level 2

AD Level 3

RS :IEC/EN 61000-4-3 Level 3

EFT :IEC/EN 61000-4-4 Level 3

SURGE :IEC/EN 61000-4-5 Level 3

CS :IEC/EN 61000-4-6 Level 3

Power-frequency Magnetic ﬁeld :IEC/EN 61000-4-8 Level 4

Low Frequency Signals :IEC/EN 61000-2-2

Warning: This is a product for commercial and industrial application in the second

environment-installation restrictions or additional measures may be needed to prevent

disturbances.

2 INSTALLATION AND OPERATION

There are two different types of models: standard and long-run models. Standard UPSs have internal

batteries, long run only have external batteries. Please refer to the following table.

VAC System Model Type Mode Type

3P IN 3P OUT 10K STANDARD RUN 10K LONG RUN

415 V / 415 V 20K 20K

30K 30K

40K 40K

60K

80K

VAC System Model Type Mode Type

3P IN 1P OUT 10K STANDARD RUN 10K LONG RUN

415 V / 240 V 20K 20K

We also offer optional parallel function for both models upon request. The UPS with parallel function is

called the ‘Parallel model’. We have detailed installation and operation procedures of the Parallel Model

in the following chapter.

2.1 Unpacking and Inspection

Unpack the box and check the package contents. The shipping package should contain:

• One UPS

• One user manual

• One RS-232 cable

• One USB cable

NOTE: Before the installation, please inspect the unit. Conﬁrm that there is no physical damage to the

unit. Unfortunately, from time to time damages occurs in transit. If the unit is damaged, please do not

install and energize the unit. Please contact PowerShield immediately.

Please keep the original packaging for future use. It is recommended to keep each ups and battery set

in their original packaging because they have been designed to provide maximum protection during

transportation and storage.

2 INSTALLATION AND OPERATION continued

2.2 Wiring Terminal View

Diagram 1:

10K(L) DUAL

20K(L) DUAL

Rear panel

Diagram 3:

30K(L) DUAL

Rear panel

Diagram 2:

10K(L) DUAL

20K(L) DUAL

Terminal cover removed

Diagram 4:

30K(L) DUAL

Terminal cover removed

2 INSTALLATION AND OPERATION continued

Diagram 5:

40K(L) DUAL

Rear panel

Diagram 6:

40K(L) DUAL

Terminal cover removed

Diagram 7:

60K(L) DUAL

Front door open

Diagram 8:

80K(L) DUAL

Front door open

2 INSTALLATION AND OPERATION continued

2.3 Schedule of Components

1 RS-232 communication port

2 USB communication port

3 Emergency power off function connector (EPO connector)

4 Share current port (only available for parallel model)

5 Parallel port (only available for parallel model)

6 Intelligent slot

7 External battery connector/terminal (Only available for long-run model)

8 Line input circuit breaker/switch

9 Maintenance bypass switch (option)

10 Input/Output terminal (Refer to diagram 3, 4, 7, 8, 11, 12, 15, 16 and 19 for the details)

11 Line input terminal

12 Output terminal

13 Input grounding terminal

14 Output grounding terminal

15 Bypass input circuit breaker/switch

16 Bypass input terminal

17 Grounding terminal

18 Output switch

19 DC breaker

20 Battery pack protection switch (DC Isolation, 120V)

21 EMBS

2.4 Single UPS Installation

Installation and wiring must be carried out in accordance with the local electric laws and

regulations by trained professionals.

1) Make sure that the mains wire and breakers of the building are rated for the capacity of

the UPS to prevent electric shock or risk of ﬁre.

2) Switch off the mains switch in the building before installation.

3) Turn off all the connected devices before connecting to the UPS.

4) Prepare cables based on the following sections 2.5 & 2.6

5) Remove the terminal cover at the rear panel of UPS. Then connect the cables according to

the following terminal block diagrams in section 2.7

(Connect the grounding/earthing wire ﬁrst when making other wire connections. Remove

the grounding/earthing wire last when connecting the UPS!)

6) Replace the terminal cover on the rear panel of the UPS.

NOTE: For dual input model with single input power system, connect input terminals to the

AC power source and connect input and bypass input together (shows dashed line in below

wiring diagrams)

Indice

Altri manuali PowerShield UPS

PowerShield

PowerShield SAFEGUARD PSG750 Manuale utente

PowerShield

PowerShield AS400 Manuale utente

PowerShield

PowerShield Centurion Series Manuale utente

PowerShield

PowerShield Centurion RT Series Manuale utente

PowerShield

PowerShield 8 Manuale utente

PowerShield

PowerShield PSDCMin12 Manuale utente

PowerShield

PowerShield Centurion RT 6000VA Manuale utente

PowerShield

PowerShield defender PSD 650 Manuale utente

PowerShield

PowerShield Ninja Slimline PSLN600 Manuale utente

PowerShield

PowerShield Defender 1200 Manuale utente

PowerShield

PowerShield GLADIATOR Manuale utente

PowerShield

PowerShield Centurion PSCE1000 Manuale utente

PowerShield

PowerShield Pilot DC 50 Manuale utente

PowerShield

PowerShield Defender Series Manuale utente

PowerShield

PowerShield Centurion PSCER6000 Manuale utente

PowerShield

PowerShield PSCM1100 Manuale utente

PowerShield

PowerShield DC Pilot 50 Manuale utente

PowerShield

PowerShield 1100 VA Manuale utente

PowerShield

PowerShield Centurion 10000 VA Manuale utente

Manuali UPS popolari di altre marche

Pylontech

Pylontech Victron & Pylontech US5000 Manuale utente

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manuale utente

Mecer

Mecer ME-1000-WTU Manuale utente

Mustek

Mustek PowerMust 530(B) Plus Manuale di installazione e funzionamento

Emerson

Emerson Liebert NXL series Manuale utente

MAKELSAN

MAKELSAN BOXER SERIES Manuale utente

Block

Block PC-0524-400-0 Manuale utente

CyberPower

CyberPower CP585LCD Manuale utente

Eaton

Eaton 3S Istruzioni per il montaggio

CyberPower

CyberPower Office Tower Series UPS 1000 Manuale utente

CyberPower

CyberPower BM100 Manuale utente

Best Power

Best Power 610 Manuale utente

Best Power

Best Power Unity/I UT3K Manuale utente

Mustek

Mustek PowerMust 400 Offline Manuale utente

Xantrex

Xantrex Trace 512 UR-UPS Manuale utente

Forza

Forza SL-1501UL Manuale utente

LEGRAND

LEGRAND keor 310081 Manuale utente

ABB

ABB Conceptpower DPA 500 Manuale utente