PowerTech PT-1090 Manuale utente

PT-1090

USER MANUAL

Wiring Diagram

Power supply

The power supply is DC15V/2.5A switching power

a.Use 12VDC, 7Ah sealed lead-acid battery, and replace it every 3-5 years.

b.A standard system with a keyboard power consumption of 180mA can support 24

hours.

c.When using without siren, connect a 2.2K resistor to clear the siren fault.

d.The total power supply demand of the keyboard, auxiliary power supply, siren, etc.

does not exceed the maximum power of the host.

e.The maximum charging current of the battery is 350mA.

f.When using wired/bus defense zones, you need to set the defense zone attributes

in the defense zone attribute settings.

Warning: Please insert SIM card before installation, then power on.

BELL

PBUS

A RLY B

+ 12V - A-ZONE-B A-KEY-B + 12V - Z1 COM Z2 Z3 COM Z4 + 12V - Z5 COM Z6 Z7 COM Z8 TAMPER

PGM

Keypad

Siren Single bus interface

Relay

module

Aux power

output

2.2K

N.O.

2.2K

N. C.

2.2K

DC15V/2.5A

SIM Card

+ -

POWER WAN LAN2 LAN4LAN1 LAN3 WPS/

RESET

Batt

EGND

SIM

L E D FL A S H

Card 1

Card 2

Speaker

interface

Pickup

interface

PGM

4G 2G

Mic

+ -

Bus

module

Wired Siren Wiring Instructions

¾ u ¥

° ¥ h

ÏÐÝ-

ÏÐÝ+

î ‚ w-  ùŒ5˜Ú  =K

° à5· ˜¾ · 5 à Œù

ÏÐÝ-

 - kk+

 - kk-

Ð.Ðh

Ê ÛØáê ÜåÜáÚê ÜçÛê ÜåØ×æÜåØáŸ

ãßØÔæØåØÙØåçâç ÛØÙâßßâê ÜáÚÖâááØÖçÜâáà ØçÛâ×-

 - kk¹

 - kk- ùŒ5˜Ú  =K

Siren

FàÒS5·˜Ï J

FàÒS5·˜ÐJ

¿âêßØéØßÔßÔåàÖ âááØÖçÜâá

Ê ÛØáç ÛØÜáãèçéâßçÔÚØâ ÙçÛØÍ ÂÁ¸ç Øåà ÜáÔß

ÙÔßßæÕØßâê¤ ÉŸÔáÔ ßÔåàê ÜßßÕØçåÜÚÚØåØ×

¨ · °

 ùŒ©õ

Z1 ) 53 @ @ ) 53 @ @ ) 53 @ @ ) 53 @ +-4*

Z 08 Expansion Module Description

+12V

GND

1 2 3 4

Power Indicator

Zone status indicator

Wiring instructions

DIP switch

+12V

GND

Light

Power indicator: always on when power is on;

Zone status indicator: Zone is enabled and flashes slowly when normal

When the zone is faulty, it always lights up.

Dialing code description

Please dial the code according to the table below.

DIP SW# Zone#

Keypad#

1111

0111

1011

0011

1101

0101

1001

41~48

49~56

57~64

65~72

73~80

81~88

89~96

DIP SW# Zone#

Keypad#

Content

Foreword 1

Features 2

Led instruction of network alarm platform 2

Insert SIM card 2

Panel led instruction 3

Insert SIM card 3

Remote phone control 4

Take alarm call from alarm panel 4

GSM SMS remote control 5

FC-7602 Dual Zone Expansion Module 5

keypad instructions 7

Wiring instructions 7

Keyboard address setting 7

Function button 8

Led lights 8

Common operation 9

Public zone 11

Duress password 12

Arm/disarm alarm panel 13

Alarm procedure 14

System maintenance 15

Programmable output 16

I. System setting 17

1. Set sys password 17

1.1 Set admin pwd 17

1.2 Set main user code 18

1.3 Set user code 18

2. Set system network 18

2.1 Set DHCP 18

2.2 Set IP 19

2.3 Set gateway 19

2.4 Set subnet mask 20

2.5 Set DNS 20

3. Set CMS 20

3.1 Phone ala center 20

3.1.1 Set CMS line 1 21

3.1.2 Set CMS line 2 21

3.1.3 Set account 21

3.1.4 Enter dial times 21

3.2 Network CMS 22

3.2.1 Set server IP 22

3.2.2 Set server port 22

3.2.3 Set CMS account 22

3.3 SIA platform 23

4. Set voice phone 23

4.1 Voice phone 23

4.2 Phone dial times 23

5. Set SYS options 24

5.1 System time 24

5.2 Entry delay 25

5.3 Exit delay 25

5.4 Bell time 25

5.5 Force arm 26

5.6 Emergency tone 26

5.7 AC power off delay 26

5.8 Door sensor check 27

5.9 WLS sensor loss 27

5.10 Voice prompt 27

6. Set wireless 28

6.1 Set remote 28

6.1.1 Enroll remote 28

6.1.2 Enter remote code 28

6.1.3 Delete remote 29

6.2 Set WLS detector 29

6.2.1 Enroll detector 30

6.2.2 Enter code 30

6.2.3 Delete detector 31

6.3 Set WLS siren 31

6.3.1 Enroll siren 31

6.3.2 Delete siren 32

6.4 RF switch 32

6.4.1 Enroll switch 33

6.4.2 Enter switch code 33

6.4.3 Delete switch 33

7.S et system zone 34

7.1 Set zone type 35

7.2 Set zone siren 36

7.3 Doorbell tone set 36

7.4 Keyboard zone 37

8. Set system area 38

8.1 Password area 38

8.2 Keypad area 39

8.3 Remote area 39

8.4 Zone area 39

8.5 Voice phone area 40

8.6 Slect partition 40

9.S et other 41

9.1 Wired zone 41

9.2 Relay 42

9.3 SIM card set 42

9.3.1 SIM default set 43

9.3.2 SIM card 1 set 43

9.3.3 SIM card 2 set 43

9.4 Timing arm/disarm 44

9.5 Single bus device 44

9.5.1 Device status 45

9.5.2 Device info 45

9.5.3 Device opttion 45

9.5.4 Device restart 46

9.5.5 Restore to fact. 46

9.6 Keypad fault disp 47

10.Advanced set 48

II. WEB IE setting 50

1. Access to the host 50

2. Basic management 51

2.1 System Kanban 51

2.2 System management 52

2.3 Wireless device 53

2.4 Single bus device 54

2.5 Smart control 54

2.6 Scene management 54

2.7 Other settings 56

2.7.1 Wired zone settings 56

2.7.2 Bypass group setting 57

2.7.3 Relay settings 57

2.7.4 Keyboard area settings 57

2.7.5 Keyboard fault display 58

2.8 System log 58

3. Network settings 59

3.1 TCP/IP settings 59

3.2 GPRS settings 60

3.3 Email settings 60

3.4 CMS platform 61

3.5 SIA platform 62

3.6 PSTN alarm platform settings                                                                 64

4. System options                                                                                                64

4.1 Alarm parameter settings                                                                        64

4.2 Alert settings                                                                                             66

4.3 Password settings                                                                                    67

4 4 Voice call settings                                                                                     68

4.5 Timing Arm/Disarm 69

5. System maintenance 70

5.1 System information 70

5.2 Time settings 70

5.3 System restart 71

5.4 System backup 72

5.5 System restore 72

5.6 System upgrade 73

5.7 Reset device 73

III. App use 74

1. Download and installation 74

2. Account registration 74

3. Add panel 75

4. Camera binding host 75

5. Add other accessories 76

Technical specifications 77

System maintenance 77

Product function limitation               78