PPA DZ HOME Manuale utente

MOTOPPAR INDÚSTRIA E COMÉRCIO DE AUTOMATIZADORES LTDA.

Av. Dr. Labieno da Costa Machado, 3526 - Distrito Industrial

CEP 17400-000 - Garça - SP - Brasil

Fone / Fax: (14) 3407-1100

www.ppa.com.br

Warning:

Do not use the

product without

first reading the

instruction

TECHNICAL MANUAL

DZ HOME

MOTOPPAR INDÚSTRIA E COMÉRCIO DE AUTOMATIZADORES LTDA.

Av. Dr. Labieno da Costa Machado, 3526 - Distrito Industrial

CEP 17400-000 - Garça - SP - Brasil

Fone / Fax: (14) 3407-1100

www.ppa.com.br

Warning:

Do not use the

product without

first reading the

instruction

TECHNICAL MANUAL

DZ HOME

INDEX

Important safety instructions .............................................................................3

Technical characteristics................................................................................... 4

Tools required for installation............................................................................. 5

Electrical installation..........................................................................................5

Care with the electrical installation....................................................................6

Care with the gate before operator ...................................................................7

Installing and fixing the operator.......................................................................8

Equipment dimensions......................................................................................8

Analog limit switch installation...........................................................................13

Maintenance...................................................................................................... 16

IMPORTANT SAFETY INSTRUCTION

Recommendation:

For the installation of the equipment, it is important that the specialized

installer follow all the instructions quoted in this TECHNICAL MANUAL

and in the USER MANUAL.

With the USER MANUAL, the installer must present all information,

uses and safety items of the equipment to the user.

Before using the DZ NEW HOME ANALOG OPERATOR, read and

strictly follow all the instructions contained in this manual.

- Before installing the operator system, make sure that the local

electrical network is compatible with the one required on the

equipment identification label;

- Do not connect the mains until installation / maintenance is complete.

Always make electrical connections to the board with the mains

switched off;

- After installation, make sure that the parts of the gate do not extend

through the roads and public promenade;

- It is mandatory to use full shutdown devices in the operator system.

DZ HOME

OPERATOR TYPE SLIDING SLIDING SLIDING

RATED VOLTAGE 220 V 220 V 127 V

NOMINAL FREQUENCY 60 Hz 50 Hz 60 Hz

RATED POWER 460 W 470 W 335 W

MOTOR ROTATION 1740 rpm 1455 rpm 1740 rpm

NOMINAL CHAIN 2,15 A 2,37 A 2,86 A

REDUCTION 1:24 1:24 1:24

LINEAR SPEED 16,4 m/min 13,7 m/min 16,4 m/min

PERFORMANCE 30 cycles/h 30 cycles/h 30 cycles/h

DEGREE PROTECTION IPX 4 IPX 4 IPX 4

TEMPERATURE RANGE -5° C / +50° C -5° C / +50° C -5° C / +50° C

ISOLATION TYPE Class B, 130 ° C Class B, 130 ° C Class B, 130 ° C

LIMIT SWITCH ANALOG ANALOG ANALOG

DZ HOME JET FLEX / DZ HOME BLDC

OPERATOR TYPE BLDC SLIDING JET FLEX SLIDING

RATED VOLTAGE 220 V / 127 V 220 V / 127 V

NOMINAL FREQUENCY 60 Hz 60 Hz

RATED POWER 100W / 130W 100W / 130W

MOTOR ROTATION 4500 rpm 4365 RPM

NOMINAL CHAIN 0,7A / 1,4A 2,75 A / 3,6 A

REDUCTION 1:22 1:22

LINEAR SPEED 36 m/min 41 m/min

PERFORMANCE 100 cycles/h 40 cycles/h

DEGREE PROTECTION IPX 4 IPX 4

TEMPERATURE RANGE -5° C / +50° C -5° C / +50° C

ISOLATION TYPE Class B, 130 ° C Class B, 130 ° C

LIMIT SWITCH Hybrid Hybrid

MAX. MASS FROM THE

GATE LEAF 400kg 400kg

MAXIMUM DIMENSION;

GATE

HEIGHT = 2,5 m LENGTH

= 3,0 m

HEIGHT = 2,5 m LENGTH

= 3,0 m

TECHNICAL CHARACTERISTICS

TOOLS REQUIRED FOR INSTALLATION

Here are some tools required to install the operator:

ELECTRICAL INSTALLATION

For electrical installation, the network shall contain the following characteristics:

- Electric network 127V or 220V;

- Have 5A circuit breakers in the electrical distribution box;

- 3/4 "diameter conduit between the electrical distribution box and the total

disconnect device;

- 3/4 "diameter conduit between the total shut-off device and the operator

connection point;

- 1/2 "diameter conduits for buttonhole, external and optional;

- 1/2 "diameter for safety photocells (optional).

PLIERS SAWING BOW SOCKET WRENCH SCREWDRIVER NUT WRENCH

LADDER

WELDING MACHINE HAMMER LEVEL TAPE MEASURE

FRAME DRILL PENCIL SANDER

- The cable for the fixed wiring must comply with NBR NM 247-3;

-The power conductor of a product for internal use must be a

flexible cable 3 x 0.75 mm²; 500 V, according to the norm NBR

NM 247-5;

-The power conductor of a product for external use must be a

3 x 0.75 mm² flexible cable; 500 V, according to IEC 60245-57.

CARE WITH ELECTRICAL INSTALLATION

To avoid damage to the wiring, it is important that all conductors be properly

attached to the operator. Wiring must be done through conduits, passing internally

through the base of the floor, ensuring that none of the wiring conductors are

trapped and damaged.

IMPORTANT

The device must be powered by a residual current (DR) device with

a rated residual current of more than 30 mA.

CONDUIT

SLIDING WAY

CARE WITH THE GATE BEFORE OPERATOR

Before adapting the machine to the gate, check the slide by following the

instructions below:

1º Step: Before Installing the operator, check that the gate is in good mechanical

condition, ie opening and closing properly. Open the gate manually and observe

the effort required. This effort should be minimal over the entire length of the course.

2º Step: Close the gate manually and check whether the exertion exerted was the

same as the previous operation.

The gate shall have a sturdy and, as far as possible, non-deformable structure.

The pulleys shall be of diameter conforming to the dimensions of the gate, are in

perfect running condition and are mounted in such a way that the gate leaf has

stability throughout its displacement. We recommend sheaves with a diameter of

at least 120 mm.

The figures below represent the two types of rails and pulleys used. The system

that uses straight section (Figure A - angle bracket) presents greater friction

and consequently greater wear. The circular section (Figure B) allows a better

displacement of the gate and less friction for the operator.

FIGURE A FIGURE B

3º Step. Make sure that the gate leaf does not jam in the opening and closing

movement. The slide rail of the gate must be perfectly rectilinear, level, unobstructed

periodically from any element or dirt that makes it difficult to slide the pulleys all the

way, as shown in the figure below.

INSTALLATION AND FIXING THE OPERATOR

Before installing the operator, remove all unnecessary cables and disable any

equipment or system connected to the mains.

EQUIPMENT DIMENSIONS

226 mm

240 mm

160 mm

The correct operation of this equipment depends on the instructions in this manual.

To secure the equipment, proceed as follows:

1º Step: Make sure that the floor is firm enough so that the equipment can be

screwed so that it is level. If it does not comply with the requirement, provide a

concrete base, following the guidelines below:

2º Step: Base dimensions should be appropriate for the dimensions of the

operator. The concrete base should be at a distance of approximately 20 mm

from the face of the gate leaf.

20 mm

GATE LEAF

SIDE VIEW

CONCRETE BASE

250 mm 300 mm

150

Questo manuale è adatto per i seguenti modelli

Indice

Manuali Apricancello popolari di altre marche

Elite

Elite CSW200UL Manuale utente

CAME

CAME FROG-PM4 Manuale utente

SOMFY

SOMFY FX230 Manuale utente

Aprimatic

Aprimatic ONDA 500 Manuale utente

Turnstiles

Turnstiles FSW 900 Manuale utente

Erreka

Erreka BUL BL33 Istruzioni operative

Erreka

Erreka VULCAN S Manuale utente

Beninca

Beninca R1-2 WBV Manuale utente

Erreka

Erreka VULCAN D Manuale utente

Motorline professional

Motorline professional FORT Manuale di istruzioni

Beninca

Beninca BOB5024 Manuale utente

AGA

AGA GATEMASTER 900 HD Manuale utente

Chamberlain

Chamberlain MotorLift HC280ML Manuale utente

SOMFY

SOMFY Dexxo RTS Pro Manuale utente

Cardin

Cardin BL Series Manuale utente

Westfalia

Westfalia 85 27 06 Manuale utente

CAME

CAME F500 Manuale utente

Extel

Extel VERA Manuale utente