PR Lighting LED Studio 3201D Manuale utente

LED Studio 3201D

LED Studio 3201T

This product manual contains important information about the safe installation and use of this projector.

Please read and follow these instructions carefully and keep this manual in a safe place for future reference.

PR LIGHTING LTD.

http://www.pr-lighting.com

2/14

INDEX

SAFE USAGE OF THE PROJECTOR……………………………………………………………………………… 3

INSTALLING THE PROJECTOR…………………………………………………………………………………... 4

CONTROL CONNECTION………………………………………………………………………………………… 5

DMX TERMINATOR………………………………………………………………………………………………. 5

SETUP OPTIONS-PROJECTOR CONFIGURATION……………………………………………………………… 6

TO SET THE DMX START ADDRESS…………………………………………………………………………….. 6

OPERATION MENU……………………………………………………………………………………………….. 7

DMX PROTOCOL………………………………………………………………………………………………….. 7

MAINTENANCE…………………………………………………………………………………………………… 8

TROUBLESHOOTING……………………………………………………………………………………………… 8

TECHNICAL DATA………………………………………………………………………………………………… 9

ELECTRICAL DIAGRAM………………………………………………………………………………………….. 11

COMPONENT ORDER CODES……………………………………………………………………………………. 12

BACK COVER……………………………………………………………………………… ……………….......... 14

Please note that as part of our ongoing commitment to continuous product development, specifications are subject to

change without notice. Whilst every care is taken in the preparation of this manual we reserve the right to change

specifications in the course of product improvement. The publishers cannot be held responsible for the accuracy of the

information herein, or any consequence arising from them.

Every unit is tested completely and packed properly by the manufacturer. Please make sure the packing and / or the

unit are in good condition before installation and use. Should there be any damage caused by transportation, consult

your dealer and do not use the unit. Any damage caused by improper use will not be assumed by the manufacturer and

/ or dealer.

ACCESSORIES

These items are packed together with the projector:

Name Quantity Unit Remark

Barn door 1 Set

Clamp 1 Pc

Safety cord 1 Pc

XLR cable 1 Pc With male and female sockets

Power cord 1 Pc

User’s manual 1 Pc

3/14

SAFE USAGE OF THE PROJECTOR

When unpacking and before disposing of the carton, check there is no transportation damage before using the projector. Should there

be any damage caused by transportation, consult your dealer and do not use the apparatus.

The projector can be used indoors and outdoors, IP20.

The projector is not designed or intended to be mounted directly on to inflammable surfaces.

The projector is only intended for installation, operation and maintenance by qualified personnel.

Do not project the beam onto inflammable surfaces, minimum distance is 2m. 2m

Avoid direct exposure to the light from the lamp. The light is harmful to eyes.

Do not attempt to dismantle and/or modify the projector in any way.

Electrical connection must only be carried out by qualified personnel.

Before installation, ensure that the voltage and frequency of power supply match the power requirements of the projector.

It is essential that each projector is correctly earthed and that electrical installation conforms to all relevant standards.

Do not connect this device to any other types of dimmer apparatus.

Make sure that the power-cord is never crimped or damaged by sharp edges. Never let the power-cord come into contact with other cables.

Only handle the power-cord by the plug. Never pull out the plug by tugging the power-cord.

When the projector is hanged to a high place, please use a safety cord provided to pass through the projector handles as a secondary

safety fixing for safety seasons. For details, refer to “INSTALL THE PROJECTOR “section.

Fresnel lens shall be changed if it has become visibly damaged to such an extent than their effectiveness is impaired, for example by

cracks or deep scratches.

Exterior surface temperatures of the projector after 5 minutes’ operation is 45℃, when achieving steady state it is 55℃.

There is no user serviceable parts inside the projector, do not open the housing and never operate the projector with the covers

removed.

If you have any questions, don’t hesitate to consult your dealer or manufacturer.

Warning: Always disconnect a fixture from the power mains before cleaning or any maintenance or

installation !

4/14

INSTALL THE PROJECTOR

The unit was designed to make installation easy: The fixture’s head can be rotated within 240°manually, before it

rotates, two side retainers are loosened with care; after the head at a desired angle, tighten two side retainers..

Take 1 clamps and 1 safety cord out from the package and mount 1 clamps on the handle of fixture with 1 retainer attached to the

clamp. Hang the fixture on the structure and fasten the screw attached to the clamp. Always ensure that the projector is firmly

anchored to avoid vibration and slipping whilst functioning. Always ensure that the structure to which you are

attaching the projector is secure and strong enough to support the weight of the fixture. For safety the projector should

have a secondary fixing with a safety cord through the handle of the unit to ensure safe mounting.

Warning:

1. The projector MUSTbe lifted or carried by the HANDLES instead of clamps.

2. For safetythe safety cord should afford 10 times of the unit’s weight.

5/14

CONTROL CONNECTION

Connection between the controller and a projector and between one projector and another must be made with a 2 core-screened cable,

with each core having at least a 0.5mm diameter. Please use the projector’s cannon 5- pin signal input and output cables as connection.

The 5-pin signal connections are connected as shown in the figure above.

Note: Care should be taken to ensure that none of the pins touch the metallic body of the plug or each other. The body of the plug is not

connected in any way. The projector accepts digital control signals in protocol DMX512 (1990).

Connect the controller’s output to the first fixture’s input, and connect the first fixture’s output to the second fixture’s input and connect

the rest fixtures in the same way. Eventually connect the last fixture’s output to a DMX terminator as shown in the figure below.

Not more than five units can be connected to power supply in series. The units can be connected to power supply in parallel. i the

voltage and frequency of the power supply should match those indicated on its nameplate.

DMX TERMINATOR

In the Controller mode, at the last fixture in the chain, the DMX output has to be connected with a DMX terminator. This prevents

electrical noise from disturbing and corrupting the DMX control signals.

The DMX terminator is simply an XLR connector with a 120Ω(ohm) resistor connected across pins 2 and 3, which is then plugged

into the output socket on the last projector in the chain. The connections are illustrated below.

6/14

SETUP OPTIONS-PROJECTOR CONFIGURATION

To browse through or change a projector’s configuration, push ENTER for about 3seconds to unlock it, after which the DMX

Address is shown meaning the menus have been entered into. TO set or browse through its functions, push the button of UP or

DOWN. After the button ENTER is pushed, the sub-menus are entered into and parameters for the currently displayed

function shown with the LCD display flickering. Push UP or DOWN button to change values(pus or minus)

Push ENTER button to save your settings and go back to the upper level menu with the display not flickering.

Push FUNC button to go back to the upper level menu with settings saved or browse through level 1 menus.

Push FUNC for 1 second or after neither button is pushed within 1minute, the menus are exited with the display’s current

brightness value shown.

If there is any DMX signal, the current DMX address will be shown ,otherwise the projector’s name and current brightness

value are shown.

TO SET THE DMX START ADDRESS

Each projector must be given a DMX start address so that the correct projector responds to the correct control signals. This DMX start

address is the channel number from which the projector starts to “listen” to the digital control information being sent out from the

controller. The projector has 2 DMX channel, so set the No. 1 projector’s address 001, No. 2 projector’s address 003, No. 3 projector’s

address 005, and so on..

Launch the projector. Press button ENTER for more than 3 seconds to unlock the panel to show DMX Address.

Push button ENTER to show DMX Address.

Push button UP or DOWN to set DMX address.

Push button ENTER to confirm and it means the setting has been automatically saved and after power-on next time, this

setting will be used.

Push button FUNC, it will return to the main menu..

7/14

OPERATION MENU

Level 1 menu Level 2 menu Level 3 menu Remarks

DMX Address 001 - 512 DMX Address

Config Setup

LED Dimmer

LED Lamp brightness 000 - 255 Value saved

Display Inversion Yes

Language Setup

English

Chinese Language Options

LCD Light Setup

LCD backlight off

No Always on

1 minutes Backlight off 1 minutes after neither button is

pushed after the menus are exited

2 minutes Backlight off 2 minutes after neither button is

pushed after the menus are exited

3 minutes Backlight off 3 minutes after neither button is

pushed after the menus are exited

LCD Dimmer

LCD backlight’s brightness 1 - 10 From dark to bright

Information

Fixture use Time XXXX Fixture’s use time

Temperature 000 - 127 LED temperature

Software Version V. X . X Software version No.

DMX PROTOCOL

CHANNEL FUNCTION DMX DESCRIPTION

1 Dimmer

000 - 255

2 Strobe

000 - 007 No strobe

008 - 255 Strobe speeds from slow to fast

8/14

MAINTENANCE

To prolong the life of the projector, it is very important to do the maintenance work. If the projector is idle for a long time, damp,

smoke or particularly dirty surroundings can cause greater accumulation of dirt on its cover and housing. So it should be cleaned to

maintain an optimum light output and at the same time to prevent it from corrupted by acid gas.

Cleaning frequency depends on the environment in which the fixture operates. Soft cloth and typical glass cleaning products should be

used for cleaning. It is recommended to clean projector at least once every 20 days.

Do not use any organic solvent, e.g. alcohol, to clean housing of the apparatus.

TROUBLESHOOTING

PROBLEM ACTION

The projector doesn’t switch on

¾Power Cord is not corrected well.

¾Power supply is damaged or abnormal. Call a qualified personnel to fix

it.

¾Connection of control board is not correct. Call a qualified personnel to

fix it.

The projector can be turned on, but LEDs do not

emit light and are out of control.

¾Connection of LED board is not correct. Call a qualified personnel to fix

it.

The lamp comes on but the projector doesn’t

respond to the controller

¾Make sure that the projector DMX address is properly set.

¾Make sure the XLR cable is in good condition

The beam appears dim

¾The projector is too hot because of ambient temperature is too high. Take

ventilation measures to make it cool.

9/14

TECHNICAL DATA

VOLTAGES:

100~240V AC, 50/60Hz

POWER CONSUMPTION:

120W@220V

LED:

Power consumption 150W

Quantity 1pcs

Manufacturers Rated LED Life 50000 Hours

COLOURTEMPERATURE:

PR-3201D 5600K

PR-3201T 3200K

CRI

Ra≥93

Luminous Flux:

PR-3201D 22°：4500lm 85°：6800lm

PR-3201T 22°：3600lm 85°：6100lm

DIMMER:

0-100% linearly adjustable

BEAMANGLE:

Spot Light

Field angle(one-tenth-peak) θ：22°

Soft light

Field angle(one-tenth-peak) θ：85°

CONTROL:

International standard protocol for DMX512 signal, 5 pin interfaces

OTHER FUNCTIONS:

fixture usage time display

LED lamps’ temperature display

Software version number display

Disconnect the signal cable, the projector automatically switch off .

HOUSING:

High-intensity injected PC housing , IP20

10/14

WORK ENVIRONMENTTEMPERATURE:

-20°C~40°C

WEIGHT:

6kg

SIZES:

LIGHT OUTPUT:

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali PR Lighting Attrezzatura per DJ

PR Lighting

PR Lighting XR 1700 FRAMING Manuale utente

PR Lighting

PR Lighting JNR-8119A Manuale utente

PR Lighting

PR Lighting LED Studio 3300T Manuale utente

PR Lighting

PR Lighting XPar 336-W Manuale utente

PR Lighting

PR Lighting XLED 300 Beam Manuale utente

PR Lighting

PR Lighting JNR DOT BEAM Manuale utente

PR Lighting

PR Lighting AQUA 350 BEAM PR-2368 Manuale utente

PR Lighting

PR Lighting Junior JNR Minifresnel 100MZ-W Manuale utente

PR Lighting

PR Lighting XPar 390 Manuale utente

PR Lighting

PR Lighting PR-8129 Manuale utente

PR Lighting

PR Lighting AQUA LED 730 FRAMING Manuale utente

PR Lighting

PR Lighting PR-8242 Manuale utente

PR Lighting

PR Lighting OMEGA Manuale utente

PR Lighting

PR Lighting CSL 1037 Manuale utente

PR Lighting

PR Lighting ARC LED 3108 Manuale utente

PR Lighting

PR Lighting Theatre Master PR-3010 Manuale utente

PR Lighting

PR Lighting XRLED 300 SPOT Manuale utente

PR Lighting

PR Lighting PR-2302 Manuale utente

PR Lighting

PR Lighting XR440 BEAM Manuale utente

PR Lighting

PR Lighting PR-8102 Manuale utente

PR Lighting

PR Lighting StarBrite Manuale utente

PR Lighting

PR Lighting PR-8110 Manuale utente

PR Lighting

PR Lighting XR-230 BEAM Manuale utente

PR Lighting

PR Lighting MEGA COLOUR 2000 Manuale utente

Manuali Attrezzatura per DJ popolari di altre marche

ALPHA LITE

ALPHA LITE ALPHA 1500 Manuale del proprietario

Chauvet

Chauvet OVATION E-930VW Manuale utente

Zumtobel

Zumtobel APHRODITE Home Manuale utente

Snow Masters

Snow Masters Zig Oscillator Manuale utente

EuroLite

EuroLite 50530554 Manuale utente

Beamz

Beamz BUV243 Manuale utente

thomann

thomann Stairville DJ Lase 40-G MK-III Manuale utente

Eagletone

Eagletone 6 Eyes Flower Manuale utente

EuroLite

EuroLite FLD-1508 Manuale utente

Technical Pro

Technical Pro LG8xSEA Manuale utente

JB Systems

JB Systems Lounge Laser DMX Manuale utente

Lightmaxx

Lightmaxx Vega Halo 90 Manuale utente

Elation

Elation FUZE WASH Z350 Manuale utente

Maverick

Maverick MK3 WASH Manuale utente

Infinity

Infinity TF-260C7 Fresnel Manuale utente

Chauvet

Chauvet EVE E-50Z Manuale utente

Eliminator Lighting

Eliminator Lighting E 138 Manuale utente

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Manuale utente