PR Lighting PR-8802 Manuale utente

PR-8802

This product manual contains important information about the safe installation and use of this

projector. Please read and follow these instructions carefully and keep this manual in a safe place

for future reference.

PR LIGHTING LTD.

http://www.pr-lighting.com

2/18

INDEX

SAFE USAGE OF THE PROJECTOR 3

INSTALLING THE PROJECTOR 4

CONTROL SYSTEMAND POWER CONNECTIONS 4

DMXTERMINATOR 5

SETUP OPTIONS-PROJECTOR CONFIGURATION 6

TO SETTHE DMX STARTADDRESS 6

OPERATION MENU 7

DMX PROTOCOL 9

INDICATION OF LED DIGITALTUBE 12

MAINTENANCE 12

TROUBLESHOOTING 12

TECHNICALDATA 13

ELECTRICAL DIAGRAM 16

COMPONENT ORDER CODES 17

Please note that as part of our ongoing commitment to continuous product development, specifications are subject to change without

notice. Whilst every care is taken in the preparation of this manual we reserve the right to change specifications in the course of

product improvement. The publishers cannot be held responsible for the accuracy of the information herein, or any consequence

arising from them.

Every unit is tested completely and packed properly by the manufacturer. Please make sure the packing and / or the unit are in good

condition before installation and use. Should there be any damage caused by transportation, consult your dealer and do not use the

unit. Any damage caused by improper use will not be assumed by the manufacturer and / or dealer.

ACCESSORIES

These items are packed together with the projector:

Name Quantity Unit Remark

Barn door 1 Pc

Clamps 2 Pcs

Safety cord 1 Pc

This manual 1 Pc

3/18

SAFE USAGE OF THE PROJECTOR

When unpacking and before disposing of the carton, check there is no transportation damage before using the projector.

Should there be any damage caused by transportation, consult your dealer and do not use the apparatus.

The projector can be used indoors and outdoors, IP67.

The projector is not designed or intended to be mounted directly on to inflammable surfaces.

The projector is only intended for installation, operation and maintenance by qualified personnel.

Do not project the beam onto inflammable surfaces, minimum distance is 5m. 5m

Avoid direct exposure to the light from the lamp. The light is harmful to eyes.

Do not attempt to dismantle and/or modify the projector in any way.

Electrical connection must only be carried out by qualified personnel.

Before installation, ensure that the voltage and frequency of power supply match the power requirements of the projector.

It is essential that each projector is correctly earthed and that electrical installation conforms to all relevant standards.

Do not connect this device to any other types of dimmer apparatus.

When the projector is hanged to a high place, please use a safety cord provided to pass through as a secondary safety

fixing for safety reasons. For details, refer to “INSTALLTHE PROJECTOR “section.

Make sure that the power-cord is never crimped or damaged by sharp edges. Never let the power-cordcomeintocontact

withothercables. Only handle the power-cord by the plug. Never pull out the plug by tugging the power-cord.

LED lens shall be changed if they have become visibly damaged to such an extent that their effectiveness is impaired, for

example by cracks or deep scratches.

Exterior surface temperatures of the projector after 5 minutes’operation is 55℃, when achieving steady state it is 70℃.

There is no user serviceable parts inside the projector, do not open the housing and never operate the projector with the

covers removed.

Always disconnect from the mains, when the device is not in use or before cleaning it or

before attempting any maintenance work !

If you have any questions, don’t hesitate to consult your dealer or manufacturer.

4/18

INSTALLTHE PROJECTOR

Take 2 clamps and safety cord out from the package and mount 2 clamps on the underside of fixture with 2 retainers

attached to each clamp. Hang the fixture on the structure and fasten the screws attached to each clamp. Always ensure

that the projector is firmly anchored to avoid vibration and slipping whilst functioning. Always ensure that the structure that

you are going to mount the projector is secure and is strong enough to support a weight of PR-8802.

WARNING:

1. The projector MUST be lifted or carried by the HANDLES instead of clamps.

2. For safety the safety cord should afford 10 times of the unit’s weight.

CONTROL SYSTEMAND POWER CONNECTION

Connection between the controller and a projector and between one projector and another must be made with a 2

core-screened cable, with each core having at least a 0.5mm diameter. Please use the projector’s cannon 3- pin signal

input and output cables as connection. The 3-pin signal connections are connected as shown in the figure above.

Note: Care should be taken to ensure that none of the pins touch the metallic body of the plug or each other. The body of

the plug is not connected in any way. The fixture accepts digital control signals in protocol DMX512 (1990).

The amount of projectors connected in parallel is not more than 32. Connect the controller’s output to the first fixture’s

input cable with a 3-pin signal cable, connect the first fixture’s output cable to the second fixture’s input cable and connect

the rest fixtures in the same way. Eventually, connect the last fixture’s output cable to a DMX terminator. Note: Only when

all the start addresses of fixtures are set the same, synchronous control could be achieved.

When the first fixture is not connected to the controller, and all the other connections are the same as above, it is master /

slave mode connection. To achieve master / slave mode, set the first fixture master , the others salve( slave is default).

As for power connections, each projector has to be supplied separately by external power. Use the power cord of each

projector to connect the mains power directly, paying attention to the voltage and frequency marked on the panel of the

projector.

5/18

DMX TERMINATOR

In the Controller mode, at the last fixture in the chain, the DMX output has to be connected with a DMX terminator. This

prevents electrical noise from disturbing and corrupting the DMX control signals.

The DMX terminator is simply an XLR connector with a 120Ω(ohm) resistor connected across pins 2 and 3, which is

then plugged into the output socket on the last projector in the chain. The connections are illustrated below.

120

DMX TERMINATOR

CONNECTION

Connect a 120 (OHM) resistor

across pins 2 and 3 in an XLR plug

and insert into the DMX out socket

on the last unit in the chain.

PIN 3

PIN 2

6/18

SETUP OPTIONS-PROJECTOR CONFIGURATION

Projector configuration can be set conveniently via push-button switch and LED display.

Launch the projector and press button ENTER for more than 5 seconds to unlock the panel, the LCD will show the

function menu of the projector, each main menu has its submenus and each submenu has a specific function. For

details, please see the “OPERATION MENU” section.

Press button UP or DOWN if you want to browse through the various Setup Options. Press button ENTER to save your

settings or enter the next menu. Press button UP or DOWN to shift.

Press button FUNC, it will return to the upper menu one by one or browse through the main menu.

TO SETTHE DMX STARTADDRESS

Each unit must be given a DMX start address so that the correct projector responds to the correct control signals. This

DMX start address is the channel number from which the projector starts to “listen” to the digital control information being

sent out from the controller. The PR-8802 have 3 DMX modes, which are standard mode, extended mode and short

mode. For example, the standard mode has 11 channels, so set the No. 1 projector’s address 001, No. 2 projector’s

address 012, No. 3 projector’s address 023, No. 4 projector’s address 034, and so on.

Launch the projector. Press button ENTER for more than 5 seconds to unlock the panel.

Press button FUNC, UP or DOWN to find “AddR” menu.

Then press ENTER to show DMX address and press UP or DOWN to set DMX address.

At this time, the address will flash continuously. Press button ENTER to confirm and it means the setting has been

enabled.

Press button FUNC, it will return to the upper menu one by one.

7/18

OPERATION MENU

1st LEVEL 2nd LEVEL 3rd LEVEL 4th LEVEL

AddR

(DMX address) XXX

（XXX:1~512）

CNFG

(Config settings)

dmX

(DMX mode)

(Default: STd)

STd

(Standard mode)

EXT

(Extended mode)

SHRT

(Short mode)

dISP

(Display setting)

(Default: ON)

OFF

(Shut off digital CRT without

pressing buttons in 5 minutes)

Brightness level control setting

[5][6]

(Default: OFF)

OFF

(

Brightnes

control i

OFF )

ON(Brightness control is ON)

T-

Timer control setting

(Default: OFF)

OFF (Timer control is OFF)

ON (Timer control is ON)

DMXS

DMX setting

(Default: ONCA)

ONCA(Only XLR)

ONWR (Only wireless)

PPCA(XLR first)

PRWR (wireless first)

WTOC (wireless to XLR)

mORS

(Master /Slave Setting)

(Default: SLAVE)

SLAV

(Slave)

mAST

(Master[1])

PAI

Unlink wireless yES

FACT

(Reset factory setup) yES

TRmd

(Transmit parameters[2]) yES

INFO

(Information)

TImE

(Power on hours) XXXX

TEm

(LED board temperature) XX

VER

(Version) X.X.X

TEST

(Test mode)

(Red)

(Green)

(Blue)

(White)

(Red/green/blue)

(Red/white/blue)

RGb

(Red/green/blue/white)

(Operation mode)

dmx

(DMX mode)

PR X

(Preset memory, PR01~PR16）

8/18

ET XX

(User memory,ET01~ET16）

COL1

(Colour 1) X

(Number: 0~14[3])

COL

(Colour 2) X

(Number: 0~14)

COL

(Colour 3) X

(Number: 0~14)

COL

(Colour 4) X

(Number: 0~14)

T*B

Timer value and brightness

value setting

T-S

Current time setting[4] HOUR

MINU

T-ON

Power on time setting[4] HOUR

MINU

T-OF

Power off time setting HOUR

MINU

B-ON

Power on by brightness setting[5] 1-100

B-OF

Power off bybrightness setting 1-100

B-EN

Check brightness 1-101

Note:

[1]. There can only be one main unit set as master at the same single circuit. Please remove DMX single when main

unit function is working.

[2]. When multiple projectors’ work together in synchronous control state, Parameters can be transmitted from the

master projector to the slave projectors in the following conditions, such as DMX channel mode, display setting

status brightness level setting, timer control setting, DMX setting, brightness value setting, timer value setting,

current time value and operation mode (User memory data is included). Please set main unit as master and others

as slave while carrying on transmitting parameters.

[3]. Colour number in user’s memory represents refer to the following table.

Number 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14

Colour R G B W RG RB RW GB GW BW RGB RGW RBW GBW RGBW

[4]. When timer control setting (T-C) is set to ON: Power on time is set to t1, Power off time is set to t2, current time is set

to t3.

If t2 >t1, when t1<=t3<t2, the projector is power on, in addition time of the projector is power off.

If t2 <t1, when t2<=t3<t1, the projector is power off, in addition time of the projector is power on.

If t2 =t1, the projector is power on.

[5]. When brightness level control (b-C) is set to ON: Power on by brightness is set to b1, power off by brightness is set

to b2, current brightness is set to b3.

If b2 >b1, when b1<=b3<b2, the projector is power on, in addition brightness of the projector is power off.

If b2 <b1, when b2<=b3<b1, the projector is power off, in addition brightness of the projector is power on.

If b2 =b1, the projector is power on.

[6]. Brightness level control setting and timer control is a logic and or relationship, if one of them to conform he off

condition, the LED lights turns off.

9/18

DMX PROTOCOL

Short

mode Standard

mode Extended

mode FUNCTION DMX DESCRIPTION

1 1 1 Dimmer 000-255 Dimming from dark to light

2 Dimmer Fine 000-255 Dimmer in 16 Bit precision

2 2 3 Colour Temperature 000 No effect

001-255 Colour temperature adjustment from

3200K to 10000K

3 4 Macros

000 No effect

001-015 Colour Temperature 3200K

016-031 Colour Temperature 5600K

032-047 Colour Temperature 7200K

048-063 Colour Temperature 10000K

064-079 Red

080-095 Green

096-111 Blue

112-127 Purple

128-143 Blue and White

144-159 Red and White

160-175 Green and White

176-191 White

192-207 Yellow and White

208-223 Purple and White

224-239 Effect 1

240-255 Effect 2

3 4 5 Red 000-255 Dimming from dark to light

4 5 6 Green 000-255 Dimming from dark to light

5 6 7 Blue 000-255 Dimming from dark to light

6 7 8 White 000-255 Dimming from dark to light

9 Hue 000-255 Hue selection

10 Saturation 000-255 Saturation from shallow to deep

11 Value 000-255 From dark to light

7 8 12 Strobe 000-009 No effect

010-255 Strobe speed from slow to fast

9 13 Preset memory

000 No effect

001-015 Preset memory 1

016-031 Preset memory 2

032-047 Preset memory 3

048-063 Preset memory 4

064-079 Preset memory 5

080-095 Preset memory 6

10/18

096-111 Preset memory 7

112-127 Preset memory 8

128-143 Preset memory 9

144-159 Preset memory 10

160-175 Preset memory 11

176-191 Preset memory 12

192-207 Preset memory 13

208-223 Preset memory 14

224-239 Preset memory 15

240-255 Preset memory 16

10 14 User Memory

000 No effect

001-015 User memory 1

016-031 User memory 2

032-047 User memory 3

048-063 User memory 4

064-079 User memory 5

080-095 User memory 6

096-111 User memory 7

112-127 User memory 8

128-143 User memory 9

144-159 User memory 10

160-175 User memory 11

176-191 User memory 12

192-207 User memory 13

208-223 User memory 14

224-239 User memory 15

240-255 User memory 16

11 15 Memory Speed

000 No effect

001-015 Speed 1,the fastest

016-031 Speed 2

032-047 Speed 3

048-063 Speed 4

064-079 Speed 5

080-095 Speed 6

096-111 Speed 7

112-127 Speed 8

128-143 Speed 9

144-159 Speed 10

160-175 Speed 11

176-191 Speed 12

192-207 Speed 13

208-223 Speed14

224-239 Speed 15

Indice

Altri manuali PR Lighting Attrezzatura per DJ

PR Lighting

PR Lighting XL 1200 Manuale utente

PR Lighting

PR Lighting Theatre Master PR-3010 Manuale utente

PR Lighting

PR Lighting JNR-8119A Manuale utente

PR Lighting

PR Lighting LED STUDIO 3605 Manuale utente

PR Lighting

PR Lighting AQUA 350 BEAM PR-2368 Manuale utente

PR Lighting

PR Lighting XS 250 Manuale utente

PR Lighting

PR Lighting XPar 150 Manuale utente

PR Lighting

PR Lighting JNR DOT BEAM Manuale utente

PR Lighting

PR Lighting LED Studio 3800T Manuale utente

PR Lighting

PR Lighting JNR BWS 350 Manuale utente

PR Lighting

PR Lighting XPar 390 Manuale utente

PR Lighting

PR Lighting ARC LED 3108 Manuale utente

PR Lighting

PR Lighting SOLO 575 Manuale utente

PR Lighting

PR Lighting PR-2302 Manuale utente

PR Lighting

PR Lighting XR480S BWS Manuale utente

PR Lighting

PR Lighting PR-8110 Manuale utente

PR Lighting

PR Lighting PR-3203T Manuale utente

PR Lighting

PR Lighting XPar 336-W Manuale utente

PR Lighting

PR Lighting PR-8242 Manuale utente

PR Lighting

PR Lighting ARC LED 1054 Manuale utente

PR Lighting

PR Lighting XLED 250 BEAM Manuale utente

PR Lighting

PR Lighting PR-8102 Manuale utente

PR Lighting

PR Lighting PR-8330 Manuale utente

PR Lighting

PR Lighting Pro Stage 150 RGBW 19 Manuale utente

Manuali Attrezzatura per DJ popolari di altre marche

ALPHA LITE

ALPHA LITE ALPHA 1500 Manuale del proprietario

Chauvet

Chauvet OVATION E-930VW Manuale utente

Zumtobel

Zumtobel APHRODITE Home Manuale utente

Snow Masters

Snow Masters Zig Oscillator Manuale utente

EuroLite

EuroLite 50530554 Manuale utente

Beamz

Beamz BUV243 Manuale utente

thomann

thomann Stairville DJ Lase 40-G MK-III Manuale utente

Eagletone

Eagletone 6 Eyes Flower Manuale utente

EuroLite

EuroLite FLD-1508 Manuale utente

Technical Pro

Technical Pro LG8xSEA Manuale utente

JB Systems

JB Systems Lounge Laser DMX Manuale utente

Lightmaxx

Lightmaxx Vega Halo 90 Manuale utente

Elation

Elation FUZE WASH Z350 Manuale utente

Maverick

Maverick MK3 WASH Manuale utente

Infinity

Infinity TF-260C7 Fresnel Manuale utente

Chauvet

Chauvet EVE E-50Z Manuale utente

Eliminator Lighting

Eliminator Lighting E 138 Manuale utente

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Manuale utente