PRECISION DIGITAL ProVu Series Manuale utente

Getting in front of a customer is expensive

and hard to do. The ProVuDemonstrator

helps you make the most of this precious

time. The ProVuDemonstrator allows you

to quickly demonstrate Precision Digital’s

PD6000 & PD6200 ProVumeters and

one of your transmitters or calibrators. The

Demonstrator makes it easier to demo

your transmitter because it can provide the

necessary power.

The ProVuDemo can also be used as a

stand-alone demo to make the last ve

minutes of your sales call more productive.

When you are done with the primary focus

of the call, take ve minutes for the ProVu

Demo. All you have to do is plug it in and

adjust the potentiometer that simulates a

voltage input (PV). You can use the built-in

LEDs to demonstrate the ProVu’s alarm and

control capabilities.

Menu Button – Use this button to

access Programming Mode and to

return to Run Mode.

Right/F1 Button – Use this button to

change the selected digit while input-

ting a numeric value in Programming Mode.

Up/F2 Button – Use this button to

increment the selected digit while in-

putting a numeric value in Programming Mode.

Enter/F3 Button – Use this button

to access or accept a menu item

while in Programming Mode.

The next time you make a sales call, be

sure to use the ProVuDemonstrator to help

present your transmitter or calibrator. It’s

sure to create the conversation that will help

generate not only sales, but also a lasting

impression.

External 4-20 mA Transmitter

(Not Included)

Easy-to-Carry Case

Fully Functional ProVuMeter

4-20 mA Analog Input

Transmitter Power

Onboard USB Connection

Relay Status Indicators

0-10 V Analog Input Simulator

233 South Street

Hopkinton MA 01748-2208 USA

Tel. (508) 655-7300 www.predig.com

ERIES

1 3

ProVuPDD6000 Demonstrator

Instruction Manual

The ProVuDemonstrator will serve to demonstrate both the PD6000 and the PD6200. The

actual product installed in the demonstrator is a PD6200 with the factory default settings

changed to make it function as a PD6000. However, when total is turned on in the system

menu, the unit will function as a PD6200. To prepare the meter for demonstration, reset the

meter to it’s factory default settings by following the instructions below.

Preparing the Meter for Demonstration

Press and

hold for

ve seconds

to enter the

Advanced Features Menu.

Press until

the diAG (diag-

nostics) menu

is displayed.

Press and hold

until the

meter ashes

rESEt (reset).

Immediately press to reset the meter to

factory defaults.

The meter will

ash all of the

LED segments

and then dis-

play dEnmo ProcES (Demo Process). The

meter has been reset to its defaults.

About the Factory Default Settings

The factory defaults congure the meter to have an input display range of 0 to 8000 with

a corresponding 0 to 10 V input from the slider. The secondary display is programmed to

display GAL (gallons). The Total and Dual Scale features are turned off.

Relays 1 and 2 are congured as alarms. Relay 1 is a low alarm with a set point of 495 and

reset point of 750. Relay 2 is a high alarm with a set point of 7500 and reset point of 6900.

Relays 3 and 4 are congured for pump alternation control. The relays alternate being on

at a set point of 6000 and reset point of 1000. Both relays will turn on at a set point of 7000,

and both off at 1000.

The alarm indicators on the meter; and the relay indicators on the demonstrator will indicate

the relay states.

Voltage Simulator (PV)

The slide control on the right side of the demonstrator serves as the 0-10 V signal simula-

tor. The input signal increases as the slider is moved upward, and decreases when slider is

moved downward.

Micro USB Connection

The PDD6000 Demonstrator includes a micro USB connector to demonstrate programming

from a PC. MeterView Pro software is included onboard and will install automatically when

the unit is plugged into a computer.

ProVuPDD6000 Demonstrator Instruction Manual

Demonstrating the PD6000 Process Meter

The ProVuDemo comes programmed with factory defaults that make it ready to demon-

strate the features of the PD6000 immediately, with no additional programming required.

The following steps describe how to demonstrate the relay alarm and pump alternation

features of the meter using the factory default settings.

Use the 0 to

10 V simulator

to adjust the

display reading

so the meter reads around 1500 gallons.

All relay lights should be off.

Raise the slide

wire until the

meter reads

around 6200

gallons. Relay number three will come on.

Notice the relay light in the above graphic.

Lower the slide

wire until the

meter reads

around 950 gal-

lons. Relay number three should turn off.

Raise the slide

wire until the

meter reads

around 6200

gallons. Relay number four will come on. This

demonstrates the pump alternation feature.

Lower the slide

wire until the

meter reads

around 950

gallons. Relay number four should turn off.

Do this a couple times so the customer can

see the pump alternation workings, and get

their head around the concept. Discuss the

advantages of this feature.

Now, raise

the slide wire

until the meter

reads around

7100 gallons. Relays number three and four

should be on, indicating both pumps on.

Keep raising

the slide wire

until the meter

reads around

7600 gallons. Relay number two will come

on, indicating the high level alarm.

Now lower the

slide wire. At

around 900

gallons, relays

number four, three, and two will turn off

indicating the high alarm has cleared and

the two pumps have been shut off. Keep

lowering the slide wire until the meter reads

around 450 gallons. Relay number one will

come on, indicating the low level alarm.

Note: The ProVu can be congured to

control up to 8 pumps. Please

refer to the section in the PD6000

Instruction Manual entitled Pump Al-

ternation Control Applications found

under Relay Operation Details.

ProVuPDD6000 Demonstrator Instruction Manual

Program Other Process Alarm Types

The ProVu can be congured to control up to 8 pumps. In order to show the versatility

of the relay operations available on the ProVu, this next sequence will change the relay

action of alarm #2 to latching. This means that the alarm state will remain in effect until the

Acknowledge Button is pressed.

Move the Volt-

age Simulator

to its lowest

position. Press

to enter Programming Mode, press

to access the SEtup (Setup) menu.

Press

until the rELay

(Relay) menu

is displayed

and then press .

Press until

the rLy 2

(Relay 2) menu

is displayed

and then press .

Press to

access the

Act 2 (Relay

2 Action) menu.

Press until

LAtcH (Latch-

ing Action) is

displayed and

then press .

Press to

return to Run

Mode. Increase

the input signal

using the Voltage Simulator to a value

above the relay 2 alarm set point of 7500,

and then reduce it to below 1000. The relay

will remain on, or latched. However, if you

press , it will unlatch the relay. Experi-

ment with other relay functions following

the instructions in the PD6000 instruction

manual under the section entitled "Setting

the Relay Operation".

Note: The F3 button is programmed to function

as an Acknowledge Button by default. In-

put 4 on the front panel of the demonstra-

tor is programmed to function as F3 by

default, so the digital input push-button

labeled 'Input 4' may also be used to

acknowledge the alarm.

More about Pump Alternation Control

The following diagram shows the previously described pump alternation control setup.

Please refer to the section in the Instruction Manual entitled "Pump Alternation Control Ap-

plications."

ProVuPDD6000 Demonstrator Instruction Manual

Dual-Scale Level Display

The ProVudual-scale level display allows the single process input to be scaled indepen-

dently into two different display values. This is most commonly used in level applications to

display height and volume, height and percent, volume and percent, or other combinations

of variables that can be derived from the single process input. Both process variables may

be displayed simultaneously on the dual-line display.

The following setup will congure the second line of the display to scale the process vari-

able input to be 0.0 to 25.5 feet.

Press to

enter Program-

ming Mode,

press to

access the SEtup (Setup) menu.

Press to

access the

Input (Input)

menu.

Press to

accept the

volt (Volt-

age) input.

This should be the default option. If it is not,

press to select it.

Press to

access the

total (Total)

menu, select

no (No) using , then press to accept.

Press to

access the

d-SCAL (Dual

Scale) menu,

select yes (Yes) using , then press

to accept. This enables dual scaling.

Press to

access the

units (Units)

menu then

press to accept the default unit tag (GAL).

Press to

access the

dec pt

(Decimal Point)

menu.

Press until

pv 2 (Process

Variable 2) is

displayed and

then press to access.

Press until

ddddd . d (First

Decimal Point

Location) is

displayed and then press to accept.

Press to

access the

ProG (Program)

menu.

ProVuPDD6000 Demonstrator Instruction Manual

Press

until SCAL 2

(Scale PV2) is

displayed and

then press to accept.

Press until

diS 2 (High

Display Value)

is displayed

and then press to accept.

Using to

change which

digit is selected

and to in-

crement the selected digit, change the high

display value to 00025 . 5 (25.5).

Press to

accept the new

value. The me-

ter will display

SAvEd (Saved).

Press to

access the

dsplay (Dis-

play) menu.

Press until

the line 2

(Display Line

2) menu is

displayed and then press to access.

Press until

d pv2 (Dis-

play PV2) is

displayed and

then press to accept.

Note: PV2 will now be displayed on display

line 2, where the units tag (GAL) was

displayed previously. Move the 0-10 V

simulator up and down to demonstrate

this capability.

Max/Min (Peak/Valley) Display

The ProVuhas the capability of tracking and storing the maximum and minimum display

values since last reset. The meter can be programmed to display maximum only, minimum

only, or alternate between maximum and minimum. The following setup will congure the

meter to alternate between maximum and minimum.

Press to

enter Program-

ming Mode,

press to

access the SEtup (Setup) menu.

Press until

the dsplay

(Display) menu

is displayed

and then press .

Press until

the line 2

(Display Line 2)

is displayed and then press .

Press until

the d HL (Dis-

play High/Low)

is displayed and then press .

11 (dual-scale cont.) 12

13 14

ProVuPDD6000 Demonstrator Instruction Manual

Demonstrating the PD6200 Rate/Totalizer

The totalizer needs to be turned on in order to demonstrate the process meter (PD6200).

Typically, Rate will be displayed in display line 1 (as denoted by the Rate indicator – Rto

the right), and Total will be displayed in display line 2 (as denoted by the Total indicator – T

underneath). The following setup will congure the meter to function as a PD6200 Rate/

Totalizer.

Press to

enter Program-

ming Mode,

press to

access the SEtup (Setup) menu.

Press to

access the

Input (Input)

menu.

Press to

accept the

volt (Volt-

age) input.

This should be the default option. If it is not,

press to select it.

Press to

access the

total (Total)

menu, select

yes (Yes) using , then press to

accept. The meter will now function as a

PD6200 Rate/Totalizer

Press to

enter Program-

ming Mode,

press until

rESEt (Reset) is displayed and press to

access this menu.

Press until

rSt t (Reset

Total) is dis-

played and then

press . This will reset the total count which

is displayed on display line 2.

When the total

reaches greater

than six digits,

the overow

indicator ( ) will illuminate.

The display

will alternate to

show the cut off

leading digits of

the number.

Reset the Total

Resetting the meter does not reset the Total value to zero, this must be done manually.

Overow Display

The ProVu can display up to 9 digits for Total or Grand Total. To demonstrate this capability,

move the 0-10 V simulator all the way to the top. When the total reaches greater than six

digits, display line 2 will alternate between the overow digits and the rst six digits of the

number. The display will alternate as illustrated below.

ProVuPDD6000 Demonstrator Instruction Manual

Press to

enter Program-

ming Mode,

press to

access the SEtup (Setup) menu.

Press until

the dsplay

(Display) menu

is displayed

and then press .

Display Total and Grand Total

The ProVumay show the Total and Grand Total simultaneously using the dual-line display.

The following instructions will congure display line 1 to read Total and display line 2 to read

Grand Total.

Press

to access

the LinE 1

(Display Line

1) menu.

Press

until the d tot

(Display Total)

is displayed

and then press .

Press

to access

the line 2

(Display Line

2) menu.

Press until

the d gtot

(Display Grand

Total) is dis-

played and then press .

Press to

enter Program-

ming Mode,

press to

access the SEtup (Setup) menu.

Press

until the relay

(Relay) menu is

displayed and

then press .

Program Rate & Total Alarms

The relays on the ProVucan be programmed to be based on the rate or total. The following

instructions will congure relay 3 as a high rate alarm with set point of 6000 and a reset

point of 5000, and relay 4 as a total alarm with a set point of 30000.

Note: Factory default sets relays 1 and 2 to be used for high and low alarms. The default meter congu-

ration of the demonstrator is for level or process displays, however these alarms will function as

rate alarms when the totalizer functions of the PD6200 are enabled.

Press to

access the

Assign (Relay

Assignment)

menu.

Press until

the asign3

(Relay #3

Assignment)

menu is displayed and then press .

ProVuPDD6000 Demonstrator Instruction Manual

Press to

accept rate

(Rate) as the

relay assign-

ment. This should be the default option, but

if it is not use to select it.

Press to

access the

Asign4 (Relay

#4 Assignment)

menu.

Press until

total (Total) is

displayed and

then press .

Press until

rly 3 (Relay

#3) is displayed

and then press

to access this menu.

Press to

access the

Act 3 (Relay

#3 Action)

menu.

Press until

auto (Automat-

ic) is displayed

and then press

to accept automatic operation.

Press to

access the

set 3 (Relay

#3 Set Point)

menu.

Using to

change which

digit is selected

and to

increment the selected digit, change the set

point value to 006000 (6000). Press to

accept this new value..

Press to

access the

rst 3 (Relay

#3 Reset Point)

menu.

Using to

change which

digit is selected

and to

increment the selected digit, change the set

point value to 005000 (5000). Press to

accept this new value.

Press until

rly 4 (Relay

#4) is displayed

and then press

to access this menu.

Press to

access the

Act 4 (Relay

#4 Action)

menu.

5(alarms cont.) 6

11 12

13 14

ProVuPDD6000 Demonstrator Instruction Manual

Press until

auto (Automat-

ic) is displayed

and then press

to accept automatic operation.

Press to

access the

set 4 (Relay

#4 Set Point)

menu.

Using to

change which

digit is selected

and to

increment the selected digit, change the set

point value to 30000 . 0 (30,000). Press

to accept this new value.

Note: Alarm #3 will set if the rate increases

above 6,000 and will reset when the

rate drops below 5,000. Use the 0-10 V

simulator to demonstrate this. Alarm #4

will set when the total reaches 30,000

and will reset once the total is reset to

zero. While the total is easily reset via the

menu system, it can also be reset via a

function key, or external digital input as

shown below.

Function Key & Digital I/O Programming

The meter buttons (F1-F3) can be programmed to perform different actions than they do by

default. The following steps show how to program the F2 function key to reset the total.

Press and

hold for

ve seconds

to enter the

Advanced Features Menu.

Press until

the uSEr (User)

menu is dis-

played. Press

to access this menu.

Press

until the F2 (F2

Button) menu

is displayed.

Press to access this menu.

Press

until rst t

(Reset Total)

is displayed.

Press to accept. The F2 button is now

programmed to reset the total to zero. Try

returning to run mode and resetting the total

with the F2 button.

17 (alarms cont.) 18

ProVuPDD6000 Demonstrator Instruction Manual

Altri manuali per ProVu Series

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali PRECISION DIGITAL Monitor

PRECISION DIGITAL

PRECISION DIGITAL PD2-6300 Manuale utente

PRECISION DIGITAL

PRECISION DIGITAL PD650-N Manuale utente

PRECISION DIGITAL

PRECISION DIGITAL Helios PD2-6262-6H0 Manuale utente

PRECISION DIGITAL

PRECISION DIGITAL PD2-6262 Manuale utente

Manuali Monitor popolari di altre marche

Linear Acoustic

Linear Acoustic LQ-1000 Manuale utente

AOC

AOC I2579V Manuale utente

Gateway

Gateway FPD1520 Manuale utente

Furuno

Furuno Mu 120c Manuale utente

Asus

Asus VB171D - 17" LCD Monitor Manuale utente

Dell

Dell S2230MX Istruzioni utente

Philips

Philips 107C64 Manuale utente

Dell

Dell S2409WFP Manuale utente

EverFocus

EverFocus EN-7517E Manuale utente

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manuale utente

Dell

Dell Precision 7680 Manuale di istruzioni

LG 50PM1M - - 50" Plasma Panel Manuale utente

Bosch

Bosch DDU 9 Manuale utente

Acer

Acer A231HL Manuale utente

Philips

Philips 86BDL4152T Manuale utente

NEC

NEC AccuSync LCD5V Manuale utente

Emay

Emay SleepO2 Manuale utente

IBM

IBM 6360 Istruzioni per l'installazione