Precision Lighting Minimo 11 Pro Manuale utente

Module

Optic

Adjustability

Housing

Insert

1. All systems must be installed by a suitably

qualied professional only. Installations

must conform to national installation

and accident prevention regulations.

2. Ensure that the luminaire is switched off at

mains supply before installing or removing.

3. Do not install IP20 luminaires in a

damp or wet location. Do not install

any xture closer than 150mm (6

inches) from any combustible material.

4. To reduce the risk of re and burns, do

not install these systems where exposed

bare conductors can be shorted or

contact any conductive materials. Do not

conceal or extend exposed conductors

through a building wall.

5. Ensure all connections are tight. Bad

connections can cause overheating,

arcing and a potential re risk.

6. Wire supply connections must be made

with U.L or compatible testing agency-

approved connectors. Always use

appropriate optics and ensure they are

tted securely.

7. Install and use only as described in this

Precision Lighting manual.

8. Use Precision Lighting recommended

optics and accessories only.

9. Luminaires may be hot, allow to cool

before touching.

10. Access to serviceable electrical

components should be kept available

for maintenance purposes.

11. Regular cleaning of these products is

important. Switch off at mains supply

and allow to cool before touching.

Clean ttings with a microbre cloth.

Then reconnect the power supply.

KEY PRODUCT FEATURES

A 11 Series Module

B 16 Series Module

C 9 degree Optic

D 11 degree Optic

E 15 degree Optic

F 25 degree Optic

G 45 degree Optic

H Honeycomb Louvre

I Standard Housing

J Trimless Housing

K Tilt ring

L Fixed ring

M Decorative Insert

N Pinhole Insert

instruction manual

Minimo 11/16 Pro

Minimo 11/16 Pro is a miniature recessed

92 CRI LED luminaire offering 360º pan with

35º tilt.

Minimo 11 Pro 6W 513lm

Minimo 16 Pro 8.4W 665lm

These instructions cover procedures for all

versions of Minimo 11 & 16 Pro with bezels

including:

Fixed and adjustable congurations

Chamfered and at bezel congurations

Decorative and Pinhole apertures

IP20 and IP54 congurations

Trimless congurations

instruction manual

Minimo 11/16 Pro

20mm

3/4 inch

106mm

4 1/5 inch

Cutout ø65mm

2 1/2 inch

3mm

1/8 inch

ø76mm

3 inch

Cutout ø65mm

2 1/2 inch

88mm

3 1/2 inch

1.5mm

1/20 inch

ø76mm

3 inch

20mm

3/4 inch

135mm

5 1/3 inches

35° tilt

Springs parallel

Minimo 16 Fixed/Tilt

3-25mm

1/8 - 1 inch

Minimo 11 Fixed/Tilt

20mm

3/4 inch

106mm

4 1/5 inch

Minimo 11 Fixed/TiltTr imless

20mm

3/4 inch

135mm

5 1/3 inches

Cutout ø76mm

3 inch

4mm

ø59mm

3 inch

3-25mm

1/8 - 1 inch

Minimo 16 Fixed/TiltTr imless

86 mm

3 2/5 inch

Minimo 11/16 Pro is a miniature recessed

92 CRI LED luminaire offering 360º pan with

35º tilt.

Minimo 11 Pro - 6W, 513lm

Minimo 16 Pro - 8.4W, 665lm

These instructions cover procedures for

all versions of Minimo 11 Pro with bezels

including:

Fixed and adjustable congurations

Chamfered and at bezel congurations

Decorative and Pinhole apertures

IP20 and IP54 congurations

Trimless congurations

1. All systems must be installed by a suitably

qualied professional only. Installations

must conform to national installation

and accident prevention regulations.

2. Ensure that the luminaire is switched off at

mains supply before installing or removing.

3. Do not install IP20 luminaires in a

damp or wet location. Do not install

any xture closer than 150mm (6

inches) from any combustible material.

4. To reduce the risk of re and burns, do

not install these systems where exposed

bare conductors can be shorted or

contact any conductive materials. Do not

conceal or extend exposed conductors

through a building wall.

5. Ensure all connections are tight. Bad

connections can cause overheating,

arcing and a potential re risk.

6. Wire supply connections must be made

with U.L or compatible testing agency-

approved connectors. Always use

appropriate optics and ensure they are

tted securely.

7. Install and use only as described in this

Precision Lighting manual.

8. Use Precision Lighting recommended

optics and accessories only.

9. Luminaires may be hot, allow to cool

before touching.

10. Access to serviceable electrical

components should be kept available

for maintenance purposes.

11. Regular cleaning of these products is

important. Switch off at mains supply

and allow to cool before touching.

Clean ttings with a microbre cloth.

Then reconnect the power supply.

1. Installing the luminaire (Trimmed)

WARNING switch off power to mains

before installation.

Cut ceiling hole at ø65mm (2 1/2 inch).

Note: Due to small luminaire size

drivers must be located remotely; cut out

is too small for dimmable drivers to pass

through.

Pull driver side connector through

hole and connect to the luminaire side

connector. See electrical instructions for

wiring schematic. Compatible drivers

listed in front page table.

Using installation springs, install xture

into the ceiling.

1. Installing the luminaire (Trimless)

WARNING switch off power to mains

before installation.

Remove LED module from tting.

Cut hole ø76mm (3 inches). Position

plaster-in ring and use appropriate

xings to secure to ceiling.

Note: Due to small luminaire size

drivers may need to be installed before

the trim is plastered in.

Trail mains cable through plaster in

ring. Apply plaster over plaster-in ring

and skim. Avoid covering wires and

connector with plaster. Cut around

inside of the aperature to ensure a neat

nish.

Once plaster is dry, connect driver to

luminaire.

Ensure the mains is switched OFF,

then connect the mains feed to the

driver.

Insert LED module into plaster-in ring

and add magnetic insert if required or if

removed during installation.

WARNING Do not connect or disconnect under load.

Ensure driver has not been powered for a minimum of 1 minute before reconnecting the

LED module after disconnecting. Do not hot plug. Failure to follow this instruction will lead to

serious damage of the LED module and driver and will not be covered by warranty.

NOTE LED module is not site serviceable.

Tampering will cause damage and will not

be covered by warranty.

NOTE Maintain correct polarity when wiring. Incorrect wiring will cause serious damage and

will not be covered by warranty. Must be installed according to SELV regulations.

Wire specification: 22 AWG, ø0.65mm diameter double insulated teflon wire.

White - Positive Black - Negative

1A.

1B.

MAINS

For IP54 version the light

should rst be installed without

the magnetic insert.

For IP54 version the light

should rst be installed without

the magnetic insert.

WARNING Do not connect or disconnect under load.

Ensure driver has not been powered for a minimum of 1 minute before reconnecting the

LED module after disconnecting. Do not hot plug. Failure to follow this instruction will lead to

serious damage of the LED module and driver and will not be covered by warranty.

NOTE LED module is not site serviceable.

Tampering will cause damage and will not

be covered by warranty.

NOTE Maintain correct polarity when wiring. Incorrect wiring will cause serious damage and

will not be covered by warranty. Must be installed according to SELV regulations.

Wire specification: 22 AWG, ø0.65mm diameter double insulated teflon wire.

White - Positive Black - Negative

3. Adding an accessory

Using two ngers or a tool remove the

magnetic insert and the LED module by

pulling sharply downwards.

Unscrew the tilt / xed magnetic ring

from the light engine to access the

accessory slot. The accessory must be

placed on the inside of the tilt / xed

magnetic ring.

4. Adjusting tilt angle and direction

Only valid for adjustable conguration

Using two ngers or a tool remove

the magnetic insert but leave the LED

module inside the trim. If the LED

module comes out with the insert

please reinsert it into the trim.

The module can be pushed inwards to

rotate up to 35º. It can also be rotated

on the magnetic surface.

2. Changing beam angle

WARNING luminaire may be hot.

Allow to cool before touching.

Using two ngers or a tool remove the

magnetic insert and the LED module by

pulling sharply downwards.

Unscrew the tilt / xed magnetic ring

from the light engine to access the optic

disc.

When installing the optic disc the

text MUST be facing you.

For IP54 version the tilt angle

should be set before the

magnetic insert is installed.

These instructions are applicable to all

Minimo luminaires including:

605, 606, 607, 608 - Minimo 11 Pro Fixed

623, 624, 625, 626 - Minimo 11 Adjustable

631,632, 633, 634 -

635, 636, 637, 638

WARNING

Do not exceed maximum number of

luminaires per driver wattage rating, see

driver datasheet for details.

Remote access required for driver.

WARNING mains supply to driver must

be OFF before connecting or disconnecting

fittings. Do not connect or disconnect

under load.

Ensure driver has not been powered for a

minimum of 1 minute before reconnecting

the LED module after disconnecting.

Do not hot plug. Failure to follow this

instruction will lead to serious damage

of the LED module and driver and will

not be covered by warranty.

NOTE Wire specication: 22 AWG,

ø0.65mm diameter double insulated

teon wire.

White - Positive Black - Negative

1. Connect Minimo luminaires in series to

the driver LED outlet.

Maintain correct polarity when wiring.

Incorrect wiring will cause serious

damage and will not be covered by

warranty. Must be installed according to

SELV regulations.

2.Wire 1-10V or DALI control to LED

driver.

Maintain correct polarity when wiring

dimming control wire. Incorrect wiring

will cause serious damage and will

not be covered by warranty. Must be

installed according to SELV regulations.

1. All systems must be installed by a suitably

qualied professional only. Installations

must conform to national installation

and accident prevention regulations.

2. Ensure that the luminaire is switched off at

mains supply before installing or removing.

3. Do not install these systems in a damp

or wet location, IP20 environments

only. Do not install any xture closer

than 150mm (6 inches) from any

combustible material.

4. To reduce the risk of re and burns, do

not install these systems where exposed

bare conductors can be shorted or

contact any conductive materials. Do not

conceal or extend exposed conductors

through a building wall.

5. Ensure all connections are tight. Bad

connections can cause overheating,

arcing and a potential re risk.

6. Wire supply connections must be made

with U.L or compatible testing agency-

approved connectors. Always use

appropriate optics and ensure they are

tted securely.

7. Install and use only as described in this

Precision Lighting manual.

8. Use Precision Lighting recommended

optics and accessories only.

9. Luminaires may be hot, allow to cool

before touching.

10. Access to serviceable electrical

components should be kept available

for maintenance purposes.

11. Regular cleaning of these products is

important. Switch off at mains supply

and allow to cool before touching.

Clean ttings with a microbre cloth.

Then reconnect the power supply.

instruction manual

Minimo 11 / 16 Electrical

Installation

500mA or 700mA Constant

Current Driver.

1 -10V

/ DALI

1 -10V

/ DALI

MAINS MAINS

500mA Constant

Current Driver Output /

Secondary

Output /

Secondary

700mA Constant

Current Driver

TCI Minijolly 1-10V 20 Driver

TCI Minijolly DALI 20 Driver

COMPATIBLE

POWER SUPPLY

PSCC-20-500-A-TC

ORDER CODE

1-2

LUMINAIRE

QUANTITY

TCI Minijolly 1-10V 20 Driver

TCI Minijolly DALI 20 Driver

COMPATIBLE

POWER SUPPLY

PSCC-20-500-A-TC

ORDER CODE

1-2

LUMINAIRE

QUANTITY

Questo manuale è adatto per i seguenti modelli

Altri manuali Precision Lighting Attrezzatura di illuminazione

Precision Lighting

Precision Lighting Domino Basis Track Series Manuale utente

Manuali Attrezzatura di illuminazione popolari di altre marche

Brizo

Brizo 8SP-MU-4 Manuale utente

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuale utente

IKEA

IKEA BJÖRKSPIREA Manuale utente

Laserworld

Laserworld Evolution Series ES-400RGB Manuale utente

Alien

Alien RG STAR Manuale utente

EuroLite

EuroLite LED B-40 Manuale utente

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuale utente

Commercial Electric

Commercial Electric 54568141 Manuale utente

CREE LIGHTING

CREE LIGHTING 304 Series Manuale utente

Goobay

Goobay 49867 Manuale utente

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuale utente

Alkalite

Alkalite Krypton KT-81 Manuale utente

Clas Ohlson

Clas Ohlson GU10 Manuale utente

DTS

DTS DELTA 10 F Manuale utente

ring

ring Solar Steplight Manuale utente

One Stop Gardens

One Stop Gardens 57696 Istruzioni per il montaggio

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuale utente

SIREM

SIREM Swimeo A2 Manuale utente