Precor PVS Manuale utente
Personal Viewing System (PVS) Installation
Guide for the P31 Console
ENGLISH
Edition Information
P/N 305262-101 Personal Viewing System (PVS) installation guide for the
P31 Console.
Copyright © 2019 Precor Incorporated. All rights reserved. Specications subject to
change without notice.
Intellectual Property Notice
All rights, title, and interests in and to the software of the Preva Business Suite, the
accompanying printed materials, any copies of such software, and all data
collected via the Preva Business Suite, are exclusively owned by Precor or its
suppliers, as the case may be.
Precor is widely recognized for its innovative, award-winning designs of exercise
equipment. Precor aggressively seeks U.S. and foreign patents for both the
mechanical construction and the visual aspects of its product design. Any party
contemplating the use of Precor product designs is hereby forewarned that Precor
considers the unauthorized appropriation of its proprietary rights to be a very
serious matter. Precor will vigorously pursue all unauthorized appropriation of its
proprietary rights.
Precor Incorporated
20031 142nd Ave NE, P.O. Box 7202
Woodinville, WA 98072-4002
1-800-347-4404
precor.com
Trademark Note
Precor, AMT, EFX, and Preva are registered trademarks of Precor Incorporated.
Other names in this document may be the trademarks or registered trademarks of
their respective owners.
Manufactured under license from Dolby Laboratories. Dolby
and the double-D symbol are trademarks of Dolby
Laboratories.
Important Safety Instructions
For safety and product information, see the Precor product documentation online
at Precor.com and the printed documentation that came with your Precor
equipment.
2
Begin Assembly of the PVS
To attach the PVS to the console, you need to reroute several cables.
IMPORTANT
Assemble the equipment according to the guidelines in this manual to ensure that
you do not void the Precor Limited Warranty. Any damage caused during
installation is not covered by the Precor Limited Warranty.
Installation Requirements
You will need the following tools to compete this assembly:
• Phillips screwdriver
• 3/16-inch socket head screwdriver
• Set of metric hex wrenches
• Set of SAE hex wrenches
• Hex-drive torque wrench with #2 Phillips screwdriver bit
Hardware Kit
The following fasteners and components are included in the hardware kit. If your
hardware kit is missing parts, contact Precor Customer Support.
Hardware Hardware name Quantity
Phillips-head screws M5 x 10 mm
(black)
8
5/16 x 3½-inch socket head screw
(use with 800 line treadmills only)
1
5/16 x ¾-inch socket head screw
(use with all equipment except the
800 line treadmills)
1
8 x 1/4-inch Phillips head tooth
lock screw
1
Hardware Hardware name Quantity
PVS monitor 1
Audio/Mobile device charger chin 1
Audio cable 1
PVS mounting bracket 1
PVS bracket cover 1
Console access cap and cover 1 of each
Long back plate (for 800 line
treadmills only) and short back
plate for all other equipment
1 of each
3
Hardware Hardware name Quantity
Tie wrap 1
Jack panel (treadmills only) 1
Charging cable 1
Ground wire 1
Television (coax) cable with 90
degree elbow adapter
1
PVS power cable 1
AC power cord (based on region) 1
4
Rewire the Equipment
You must rewire the equipment to support the PVS functionality. This section
contains procedures to rewire the following equipment to accommodate a PVS:
• Treadmill
• EFX
• AMT
• Recumbent Bike
• Upright Bike
• Climber
Before You Begin
IMPORTANT
Disconnect power to equipment before you begin.
Perform the assembly steps in the order presented.
IMPORTANT
At least two people are required to assemble the equipment. DO NOT attempt
assembly by yourself.
To rewire the equipment, you need the following new cables from the hardware
kit:
• Television (coaxial) cable
• Power cable (disconnect the power cable from the AC adapter)
NOTE
Tape the television and power cables together to make it easier to feed them
through the equipment. In addition, a sh tape (a thin metal strip with a hook
or clasp on one end, available from professional hardware vendors) can be
helpful threading cables through the long equipment tubes.
Before you begin to rewire, remove the screws that secure the console in place.
NOTE
Precor recommends that you have another person hold the console steady to
prevent it from falling while you rewire the equipment.
5
Rewire the Treadmill
To thread the PVS power and television cables through the treadmill, refer to the
following table and gure:
Step Procedure
Remove the console back cover, then the top cover on the upright
support.
Remove the hood and blank panel.
Thread the cables through the console mount. Secure them using the
three wire retainers and route the cables behind the spacer ring,
identied by an arrow in the gure.
Route the cables down the cable channel in the upright support.
Pull the cables from the bottom of the right upright support and
thread them across the base frame. Secure them with wire retainers.
N/A Thread the cables downward through the opening in the base frame
and pull the cables out through the opening at the base of the unit.
N/A Reattach the top cover on the upright support.
Important Do not pinch the cables when reinstalling the plastic covers.
Attach the new jack panel (in the hardware kit) to the base frame
using the two screws that attached the blank panel.
2
6
Rewire the 800/600 EFX
Step Procedure
On the center column, lift the moisture seal upward and remove it.
Remove the front top cap from the center column.
To remove the bottle holder, strike the plastic parts of either side (see
grey circle in graphic) with the heel of your palms. The holder pops
off.
Slide the front cover off.
Remove the two screws that secure the blank jack plate and set them
aside.
Attach the following cables to both sides of the new jack plate:
A Communication cable
B Television (coax)
C Power cable
Use the wire retainers to hold the cables in place.
N/A Attach the new jack plate using the two screws removed in step 5.
Feed the cables up the EFX neck and out the opening at the top.
N/A Reattach the covers and parts removed in steps 1 through 4.
A
B
C
7
Rewire the 700 EFX
Step Procedure
Remove the bottom front cover.
Using sh tape, thread the cables down the center column to the
bottom.
Remove the two screws that secure the blank jack plate on the front
bottom cover.
Attach the following cables to both sides of the new jack plate:
A Communication cable
B Television (coax)
C Power cable
Snap the front bottom cover into place and attach the new jack plate
using the two screws removed in step 3.
A
B
C
8
Rewire the AMT
Remove the front and side access covers to provide sucient space to install the
console cables.
IMPORTANT
Before continuing with the following procedure, be sure to remove any ties or
other materials that hold the side arms in place before the supports are installed.
To thread the new cables through the equipment:
2
Step Procedure
Lift the moisture seal upward and remove it from the center column.
Extend a nger through the moisture seal opening and under the
front edge of the top cover on one side. While pressing upward on
the top cover, use the heel of your palm to tap gently below its front
edge and release it. Repeat this step to release the other side of the
top cover.
While holding the front edge of the top cover up, use the palm of
your other hand to tap gently just below the cover's back edge. Lift
the cover up and out of the way.
Remove the two screws at the bottom corners of the front cover.
Gently press in on each of the side covers, just behind the front edge
and about 8 inches from the bottom, while pulling the front cover
assembly forward to disengage it. Move the front cover assembly
forward and slightly upward to remove it.
Note Each side cover has a small triangular mark to show you where
to press.
N/A Thread the PVS power and television cables through the center
column and guide them through the opening at the bottom.
Important The cables must be secured in the cable retainers attached to
the frame. They must then pass through the square opening in the jack
panel.
Guide the arm openings in the front cover around the arms of the
AMT, taking care that the tabs at the bottom corners of both
openings are inside the two side covers, then guide the front cover
until the latches on the side covers click into place. Reattach the two
screws at the bottom corners of the front cover. Fully tighten the
screws.
N/A Important In the following step, do not apply excessive force to seat the
cover.
Position the rear edge of the top cover so that the clips on the top
and back covers are engaged securely. Gently snap the front edge of
the top cover into place. Use the palm of your hand if necessary.
N/A Wrap the moisture seal around the center column below the heart
rate sensor grips, then t it into the top cover. Make sure that the
surfaces and edges of the moisture seal are ush with those on the
top cover.
9
Rewire the Recumbent Bike
Remove the front and side access covers to provide sucient space to install the
console cables.
NOTE
You need to remove only one side cover to thread the cables.
To thread the new cables through the equipment:
Step Procedure
Remove the top cover.
Remove the back cover.
Remove the side cover.
Remove blank jack panel from the front base of the bike.
Feed the cables down the mast.
The cables need to be threaded around the bolts that hold the center
mast in place.
Feed the cables through the square opening in the jack panel using
the communication cable’s wire retaining feature, then slide the jack
panel back into its mounting.
Important The cables must be secured in the cable retainers along the
frame (with the communications cable) and then exit the square hole in
the jack panel. You may need to slide out the jack panel to remove the
CAT5 coupler and feed the cables through the hole. If so, return the jack
panel to its previous position when you are nished.
N/A Reattach the bike covers in reverse order as removed in rst three
steps.
10
Altri manuali per PVS
1
Indice
Altri manuali Precor Elettronica per il fitness
Precor
Precor P10 Istruzioni di montaggio
Precor
Precor UBK13 Manuale utente
Precor
Precor Spinner Chrono Manuale
Precor
Precor Spinner Chrono Manuale utente
Precor
Precor P80 Console Istruzioni di montaggio
Precor
Precor P30 Console Manuale
Precor
Precor P30 Console Istruzioni di montaggio
Precor
Precor Console Manuale utente
Precor
Precor P30 Console Manuale utente
Precor
Precor P10 Istruzioni di montaggio
