Premier Mounts FPS-300 Manuale utente
www.mounts.com | North America 800.368.9700 | International +1-714-632-7100
1321 S. State College Blvd., Fullerton, CA 92831 USA
Warranty, Garantie, Garantía, Garanzia, Garantie, Waarborg: http://www.mounts.com/warranty
9535-000-011-0X Rev.2
Installation Guide
Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids
FPS-300
53.38
(HOLD DIM)
16.00
16.00 16.00
Display Width
FACTOR
15.250"
Mounting
Distance
Desired
Distance
C
L
OPTIONAL POWER BOX
OUTLET LOCATION
OPTIONAL POWER BOX
OUTLET LOCATION
THE FIRST SLOTS MUST
ALWAYS HAVE AN ANCHOR
ON EITHER END IN ANY GIVEN
INSTALLATIONAPPLICATION
ROLLER PLATE
Mounting Distance = Display Width/2 + Desired Distance - 15.25”
WALL STRUCTURE
M8 x 16mm
1/4”
M5 x 10mm M3 x 8mm 1/4” x 3”
M4 x 5mm
#10
#8 x 1-1/4”
x8 x6 x4 x8
x18
x20
x20
x2 x1
x5
x8
1/8” / 3.25mm
(Wood Only)
7/16”
1
Included components
Required for installation
Note: Prior to installation start, the installer has the option
of concealed power and signal boxes mounted flush on
either the left or right side upper mounting rail end caps. If
power and signal cable are to be run externally to the end
cap, please note provisions have been made to allow for
external “wire mold” channel to be run into the end caps as
well.
Unpack all FPS-300 system components and confirm all
components called out in the supplied parts list are ac-
counted for. With all components laid out select the upper
mounting channel pieces as these will be the first part of the
system to install.
Note: If you are using the optional concealed left or right
side power and signal box sections, install only one side of
the upper track guide along with the power signal box cover
that is opposite of where the power and signal is coming
from. Power and signal cables must run together from either
the left or right side for proper operation of the system.
Warranty: http://www.mounts.com/warranty
Garantie, Garantía, Garanzia, Garantie, Waarborg
Updates: The most up-to-date installation
guides can be found at mounts.com
www.mounts.com | North America 800.368.9700 | International +1-714-632-7100
9535-000-011-0X Rev.2
2
3
Installation Guide
Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids
FPS-300
Depending on the composition of the installation wall, drill
the pilot holes with the proper size drill bit to a depth allow-
ing for full penetration of the mounting screw in the wall to
provide a level and firmly attached upper mounting channel.
Take one 48 in. upper channel section (A) and place it
horizontally on the wall and level at the desired height, in
line with both the predetermined stud locations and with
anchoring position in the far right or left slot. Mark through
the upper channel mounting holes directly on the wall.
Note: Be sure you have clear space behind the dry wall if
you are using the concealed mounting power and signal box
option. For concrete or other solid wall construction, follow
the same process as above, but using suitable hardware for
best installation requirements.
A
7/16” 1/4”
1/4” x 3”
#8 x 1-1/4”#10
4
5
Once the center height is confirmed at 53.38” between the
upper and lower channels, mark and drill pilot holes for the
#10 plastic anchor. Follow the same procedure as step 4
above to install the lower two mounting channel sections,
ensuring the interlocking tabs are together.
Note: Be sure the upper and lower channels are level with
each other and in line at the same starting point as called
out in the instructions.
Once the mounting pilot holes have been drilled, take the
first 48 in. (1219mm) section of mounting channel and se-
cure it level on the wall with the mounting hardware provid-
ed. Once the first upper channel is secure, follow the same
procedure for the second 48 in. (1219mm) upper channel.
Do not overtighten the screws.
A:Make sure the two upper channel sections are locked to-
gether inside the locking tabs provided at the channel ends.
Do NOT tap on the small protruding tabs.
A
Warranty: http://www.mounts.com/warranty
Garantie, Garantía, Garanzia, Garantie, Waarborg
Updates: The most up-to-date installation
guides can be found at mounts.com
www.mounts.com | North America 800.368.9700 | International +1-714-632-7100
9535-000-011-0X Rev.2
6
7
Installation Guide
Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids
FPS-300
Install the power signal boxes to each end.
Complete all electrical installation at this time.
Note: The upper slider assembly can also be wired using
appropriate wire connection.
With both upper and lower channels level and secure to the
wall, the main slider assembly can be raised (two people
recommended) with the upper rollers properly seated into
the upper channel receiver slots. Once fully seated, the low-
er rollers should be on center with the lower roller channel.
9
8
Use UL or VDE listed flexible electrical cord appropriate
for this installation. (Contact your local electrician for more
information).
Push the cord into the plastic guide track, leaving sufficient
length open on either end for full motion of the display on
the slider. Hard wire the cords to universal electrical box.
Repeat for signal cable installation.
Using the spirit level supplied, adjust the stand off of the
lower roller wheels to provide a level vertical for the slider
frame on the wall. Loosen the locking screw at the bottom of
the roller using a Phillips head screwdriver. Install the dome
plug and tighten the bottom lock screw once the slider is
level.
Warranty: http://www.mounts.com/warranty
Garantie, Garantía, Garanzia, Garantie, Waarborg
Updates: The most up-to-date installation
guides can be found at mounts.com
www.mounts.com | North America 800.368.9700 | International +1-714-632-7100
9535-000-011-0X Rev.2
11
10
Installation Guide
Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids
FPS-300
Lay the plastic track glide unit with power and signal cable
installed within track section fully inside the upper channel
receiver section. Dress out the power and signal cable at
each end using the tie wraps supplied to insure smooth full
travel of the slider assembly in both the vertical and horizon-
tal movements of the system.
Note: The orientation of the track will be determined by
where the power box was installed.
Remove the top cover on the slider assembly and set aside
for later re-install.
Power
M5 x 10mm M3 x 8mm
x2 x4
13A
12
Secure both ends of the cable track system to the upper
channel structure with the track brackets and hardware sup-
plied as shown in the visual diagram.
Secure the power strip to the frame using two (2) M3x8mm
screws and two (2) M3 kep nuts.
Double check all power and signal cables are properly se-
cured to the system channels as to not cause any pinching
of the cables during any movement of the slider system.
M5 x 10mm
x2
Warranty: http://www.mounts.com/warranty
Garantie, Garantía, Garanzia, Garantie, Waarborg
Updates: The most up-to-date installation
guides can be found at mounts.com
www.mounts.com | North America 800.368.9700 | International +1-714-632-7100
9535-000-011-0X Rev.2
14
13B
Installation Guide
Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids
FPS-300
Re-install the upper channel and end covers securely at this
time.
Use additional tie wraps as needed for proper wire and
cable routing.
M4 x 5mm
M4 x 5mm
x8
x8
15B
15A
Install the power signal box covers and channel covers.
Indice
Altri manuali Premier Mounts Supporto TV
Premier Mounts
Premier Mounts ECM-MAC2 Manuale utente
Premier Mounts
Premier Mounts MVW46 Manuale utente
Premier Mounts
Premier Mounts PMC-MM-500 Manuale utente
Premier Mounts
Premier Mounts ECM-3763Q Manuale utente
Premier Mounts
Premier Mounts RFM Manuale utente
Premier Mounts
Premier Mounts AM100 Manuale utente
Premier Mounts
Premier Mounts AM175 Manuale utente
Premier Mounts
Premier Mounts CTM-MS1 Manuale utente
Premier Mounts
Premier Mounts Universal Flat Mount FM3 Manuale utente
Premier Mounts
Premier Mounts INW-42 Manuale utente
Premier Mounts
Premier Mounts PSD-BW Manuale utente
Premier Mounts
Premier Mounts P5080F Manuale utente
Premier Mounts
Premier Mounts Rotary series Manuale utente
Premier Mounts
Premier Mounts PMC-MM-501 Manuale utente
Premier Mounts
Premier Mounts MM-EP15 Manuale utente
Premier Mounts
Premier Mounts GB-VESA42 Manuale utente
Premier Mounts
Premier Mounts GB-INWAVP Manuale utente
Premier Mounts
Premier Mounts PCM-MS2 Manuale utente
Premier Mounts
Premier Mounts UFA-XL Manuale utente
Premier Mounts
Premier Mounts FTP-096 Manuale utente
