prime3 TAG41 Manuale utente
Angle grinder
Winkelschleifer
Szlierka kątowa
TAG41
Owner’s manual
Bedienungsanleitung
Instrukcja obsługi
TAG41
1
2
3
4
5
6
7
TAG41
źBefore maintenance work always disconnect the unit from the power
supply.
Before using the device, read the operating instructions and follow the
instructions contained therein. The manufacturer is not liable for any
damage caused by the use of the device contrary to its intended use or
improper operation.
In order to achieve the highest satisfaction, enjoy the performance of
the product and learn all its features and functions, please read this
manual before using this product.
The operating manual should be kept so that it can also be used during
later use of the product.
źIt is necessary to check, if total current consumption of all devices
plugged into the wall outlet does not exceed the fuse in the circuit.
źThe device is not designed to be controlled via an external timer,
separate remote control, or other equipment that can turn the device
on automatically.
źThe device should only be connected to an socket with values corre-
sponding to the values on the rating label.
źIf you are using an extension cord, make sure that the total power
consumption of the equipment plugged into the extension cord does
not exceed the extension cord power rating. Extension cords should
be arranged in such a way as to avoid tripping hazards.
źDo not let cord hang over edge of counter, or touch any hot surface.
źWhen unplugging the power cord from electrical outlet, hold it by the
plug only and remove the plug carefully. Never pull the cable as it
may cause damage to the plug or power cord.
źDamage to the power cord or plug can lead to an electrocution
hazard.
źThis device is for domestic use only. Do not use for any other pur-
poses.
źNever leave the product connected to the power source without
supervision.
IMPORTANT INFORMATION
3
źNever expose the product to atmospheric conditions such as direct
sun light or rain, etc... Never use the product in humid conditions (like
bathroom or camping house).
źAll the repairs should only be performed by authorized service
professionals. Any attempted unauthorised repairs performed can be
a hazard to the user.
źThe power cable should be periodically checked for damage.
źIf the power cable is damaged the product should be taken to a
professional service location to be xed or replaced to prevent any
hazards from arising.
źNever use the product with a damaged power cable or if it was
dropped or damaged in any other way or if it does not work properly.
Do not try to repair the defected product by yourself as it can lead to
electric shock. Always return the damaged device to a professional
service in order to repair it.
źNever use the product close to combustibles.
źThe device should be cleaned regularly complying with the recom-
mendations described in the section on cleaning and maintenance.
źThe appliance must not be used by children. Keep the appliance and
its cord out of the reach of children.
źThe appliance may be used by individuals with limited physical,
sensory or mental capability as well as those without knowledge of or
previous experience in the use of similar appliances, provided such
individuals are supervised or instructed with regard to the safe
operation of the appliance and are informed about the potential
hazards.
źAdditional precautions should be taken when using this device in the
presence of children or pets. Do not allow children to play with the
device.
źNever put the power cable, the plug or the whole device into the
water or any other liquids.
źDo not place the device near sources of heat, ame, an electric
heating element or a hot oven. Do not place on any other device.
4
TAG41
TAG41
źDo not lean out too far when working with your power tool.
źDisorder and insufficient lighting lead to accidents.
źOnly Original accessories should be used, as well as accessories
recommended by the manufacturer. Using accessories which are not
recommended by the manufacturer may result in damage of the
device and may render the device unsafe for use.
źDo not use power tools in explosive atmospheres, i.e. in the presence
of ammable liquids, gases or dust.
źA moment of carelessness may cause losing control of your tool.
źIf it is possible to t power tools for dust extraction or collection,
check that they are tted and working correctly.
źKeep your workplace tidy and well lit.
źUsing such power tools reduces the risk posed by the presence of
dust.
źMaintain a stable posture and balance. This allows you to keep better
control of your power tool in unforeseen situations.
źKeep children away from the work area and DO NOT allow children to
pull on the power cord - this can cause serious injury.
źRemove any spanners or tools from the power tool before starting it.
A tool or spanner still connected to the rotating part of the power
tool may cause personal injury.
źWear appropriate clothing. Do not work in loose clothing and do not
wear jewellery while working. Keep your hair, clothing and gloves
away from moving parts. The moving parts of a power tool can catch
and pull in loose pieces of clothing, jewellery or long hair.
źAvoid starting the power tool unintentionally. Make sure the power
switch is in the OFF position before connecting the power tool to the
mains. Carrying a power tool with your nger on its trigger or
plugging in a power tool after switching it on can lead to accidents.
źBe careful when working with power tools, concentrate on your work
and use common sense. Do not use a power tool when tired or under
the inuence of drugs, alcohol or medication. Even a moment of
carelessness while working with a power tool can lead to a serious
accident.
5
źThe device may only be used in a dry, well-lit environment.
źBefore making any adjustments, changing accessories or storing the
power tool, move the switch to the off position to disconnect the
power tool from the power supply. Such precautions reduce the risk
of accidentally starting the power tool.
źLoss of control of the power tool may result in personal injury.
źUse appropriate detectors to locate the installation or seek assistance
from your local service provider. Contact with live wires may result in
a re or electric shock. Damage to the gas tube may lead to an
explosion. Bursting of a water pipe leads to material damage.
źWhen carrying out work where the tool or clamping attachment
could come into contact with concealed electric wires, hold the power
tool only by insulated surfaces. Contact of the tool or clamping
attachment with a live electrical conductor may cause voltage to be
transmitted to non-insulated metal parts of the power tool, causing
a risk of electric shock.
źThis tool should not be used by anyone under the age of 16.
źHold the power tool rmly. High reaction torques may periodically
occur while tightening and loosening screws and bolts.
źEnsure that the vents are free from debris.
źSecure the workpiece. Clamping the workpiece in a clamping device
or vice is safer than holding it by hand.
6
TAG41
SYMBOLS
• The following symbols may appear in the operating instructions or on the tool’s nameplate.
• These signs contain important information about the product and instructions on how to use it.
WEAR PERSONAL PROTECTIVE EQUIPMENT
• Wear safety glasses according to En166
• Use protective masks in accordance with En149
• Use other types of proper personal protective equipment, depending on the type of work involved.
Read the user manual.
Use ear protection
Wear protective glovesGeneral warning
Wear protective clothing
Wear a protective mask
Wear safety glasses
Fire hazard
Wear respiratory protection
Electric shock hazard
TAG41
7
Before replacing the disc, disconnect the device from the power source.
To replace the grinding disc, use the included hole wrench for the front bolts.
Check that the disc has the appropriate technical specication. Use only discs with a minimum per missible
rotational speed of 12000 rpm and a peripheral speed of 80 m/s.
Grinding discs:
źUse the spanner to loosen the bolts securing the discs.
źRemove the spanner from the anged nut.
źPress the spindle lock to lock the chuck rotation.
The disc must not exceed the diameter specied.
Kickback:
The kickback is sudden and uncontrollable, the device reacts to the jamming or blockage of the cutting
device. Jamming or blocking results in a sudden jerk, in the direction opposite to the rotation of the disc.
Kickback is the result of not reading the safety instruction.
To avoid kickback, follow the safety instructions and use methods to prevent it.
Device operation:
The lock reduces the risk of turning the device on or off.
To turn the device on, move the button to the upper position until it hits the lock ing tab
To turn the device off, press the lower part of the button, it will pop out of the lock.
Replacing the grinding disc:
The device is equipped with a switch lock.
Using of safety guard:
Installing the additional handle:
The handle can be mounted on either side of the device.
The disc guard should be rmly attached to the device and set so that the user is saf e when cutting, i.e. it
should be mounted in such a way that its covered part is on the user's side.
Methods to prevent kickback.
5. Safety guard
6. Switch with a locking function
b) Keep hands away from the cutting part of the device.
c) The user should stand in such a position that, in the event of a k ickback, they are not within reach of the
grinder disc.
1. Main handle
2. Auxiliary handle
7. RPM adjustment
a) Hold the device by the two handles rmly and securely. Always use the additional handle. – The operator
can control the torque and the resultant kickback forces if appropriate precautions are taken.
CAUTION: The device may injure the user if used improperly.
Description of the device
3. Spindle lock
4. Spindle
TAG41
8
źWeight: 1.8 kg
źRotational speed without load: 2300-11,000 r pm
źAuxiliary handle
Noise Emission (Sound Power) LWA 102 dB(A)
Noise Emission (Sound Pressure) 86 LpA dB(A)
źRPM adjustment
źIncluded: 4 discs, spanner, handle, brushes
The declared vibrations has been measured according to the standard test method and can be used to
compare tools.
The typical equivalent A-weighted sound level determined according to EN62841:
The declared vibrations can also be used in the initial exposure assessment.
Maximum vibrations on the main handle: 11.2 m/s2
źDimensions: 31.5 x 7 x 9.5 cm
źPower cord length: 1.8 m
Uncertainty of Noise Emission Measurement KpA, KWA 99 dB(A)
The total value of vibrations (sum of vectors in 3 axes) is determined according to EN62841:
Maximum vibrations on the additional handle: 9.8 m/s2
Uncertainty of Vibration Emission Measurement K 1.5 m/s2
Permissible Operating Time: 15 minutes of operation, 30 minutes off.
źPower supply: 230-240 V ~ 50 Hz, power 800 W, max 1400 W
SPECIFICATIONS:
ź2 cutting discs, 2 grinding discs
źDisc diameter: 125 mm
źDisc opening diameter: 22 mm
źSpindle thread: M14
źHigh maximum power: 1400 W
Do not push the device too hard against the workpiece.
Do not change the cutting angle and bend the disc in the wor kpiece when cutting.
Before starting to work with the device, check that the disc is tightened and properly installed, the disc guard
is tightened and set in the right direction.
Keep the ventilation apertures (air inlets and outlets) of the device free of dir t. Wipe the device with a dry
cloth or blow it with compressed air. Keep the work tool chuck free of dust. It is recommended to clean the
device after each use. Do not immerse in water or other liquids. Do not use aggressive cleaning agents or
solvents.
Before cleaning and maintenance, make sure the device is disconnected from the power source.
While cutting or grinding the grinder should be guided at a constant speed, depending on the mater ial.
Tips for working with the device:
CLEANING AND MAINTENANCE
TAG41
9
Indice
Lingue:
