Primera LX600 Manuale utente
User’s Manual
© 2020 All rights reserved.
For the most recent version of this manual please visit
http://www.primera.com/LX600downloads
2
Notices: The information in this document is subject to change without notice. NO WARRANTY OF ANY KIND IS MADE
WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE. No liability is assumed for errors contained herein or for incidental or
consequential damages in connection with the furnishing, performance, or use of this material. This document contains
proprietary information that is protected by copyright. All rights are reserved. No part of this document may be
photocopied, reproduced, or translated into another language without prior written consent.
Trademark Acknowledgments: Primera and Primera LX610 are registered trademarks of Primera Technology, Inc.
Windows is a registered trademark of Microsoft Corporation. All other trademarks are the property of their respective
owners.
Revision History
Edition 1.2, Copyright 2020, All rights reserved.
FCC Compliance Statement: This device complies with part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
For Users in the United States: This product is intended to be supplied by a UL listed Direct Plug-In Power Supply
marked "Class 2"or a UL listed ITE Power Supply marked "LPS" with output rated 12VDC, 5A or higher. This equipment
has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. In
a domestic environment this product may cause radio interference, in which case the user may be required to take
adequate measures. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
•Re-orient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
Use of shielded cables is required to comply with the Class A limits of Part 15 of the FCC Rules. You are cautioned that
any changes or modifications not expressly approved in this manual could void your authority to operate and/or obtain
warranty service for this equipment.
For Users in Canada: This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus set
out on the Radio Interference Regulations of the Canadian Department of Communications. Le present appareil
numerique n'emet pas de bruits radioelectriques depassant les limites applicables aux appareils numeriques de la class
A prescrites dans le Reglement sur le brouillage radioelectrique edicte par le ministere des Communications du Canada.
072820
3
4
Table of Contents
Section 1: Getting Started.....................................................................................................................................6
1A Choosing a Good Location...........................................................................................................................6
1B Unpacking and Inspection ...........................................................................................................................7
1C Installing the Roll Holders............................................................................................................................8
1D Identifying the Parts..................................................................................................................................12
Section 2: Media and Cartridges.........................................................................................................................15
2A Label and Roll Specifications .....................................................................................................................15
2B Installing Pre Die-Cut Label Stock..............................................................................................................18
2C Replacing Ink Cartridges ............................................................................................................................22
2D Adjusting the Gap Sensor Position (Non-rectangles Only)........................................................................24
Section 3 Primera PrintHub (PC).........................................................................................................................26
3A Using the Cost Estimator ...........................................................................................................................27
3B Set the Gap Sensor Mode..........................................................................................................................28
3C Set the Present/Cut Mode.........................................................................................................................30
3D Adjusting Print Alignment .........................................................................................................................32
3E PrintHub Settings.......................................................................................................................................34
3F PrintHub Printer Settings ...........................................................................................................................36
3G Multiple Printer Support ...........................................................................................................................37
Section 4: Printing from a PC..............................................................................................................................38
4A Using BarTender for Pre Die-Cut Printing..................................................................................................38
4B Add Text, Barcodes and Graphics to a BarTender Label ...........................................................................45
4C Printing from Other Programs...................................................................................................................46
4D Creating a Full Bleed Print.........................................................................................................................47
4E Printer Driver Settings................................................................................................................................49
Section 5: Printing from a Mac ...........................................................................................................................52
5A Print Utility Settings (LX600 Config Utility)................................................................................................52
5B Adjusting Print Alignment/Label Offsets ...................................................................................................53
5C Set the Stock Sensor Mode........................................................................................................................55
5D Set the Output Mode ................................................................................................................................56
5E Printing from Swift Publisher.....................................................................................................................58
5F Creating a Custom Page Size......................................................................................................................64
5G Creating a Full Bleed Print.........................................................................................................................66
5
5H Printer Driver Settings...............................................................................................................................67
Section 6: Troubleshooting.................................................................................................................................71
6A Solving Print Alignment Problems.............................................................................................................71
6B Maintenance..............................................................................................................................................73
6C Poor Print Quality –Cleaning the Cartridge ..............................................................................................74
6D Technical Support......................................................................................................................................77
Section 7: Technical Specifications.....................................................................................................................78
6
Section 1: Getting Started
THANK YOU…
...for choosing an LX600 Color Label Printer. The LX600 Color Label Printer will print razor-sharp text
and barcodes, vibrant colors, and even stunning photo-realistic photographs directly onto rolls of
labels, card stock and a variety of other approved media.
This User's Manual is your complete step-by-step guide to quickly and easily setting up and printing
with your new Color Label Printer!
1A Choosing a Good Location
•Place the printer on a flat surface in a location with adequate air circulation to prevent
internal heat buildup.
•Do not place the printer near heat sources such as radiators or air ducts, or in a place subject
to direct sun light, excessive dust, mechanical vibration or shock.
•Allow for adequate clearance in front of the printer to accommodate the printed label stock
as it is leaving the printer to avoid the possibility of binding or jamming of the label stock.
•Allow for 6” of clearance behind the printer to accommodate loop creation during cutting
operations. The area directly behind the printer must also not be obstructed by USB or
power cables connected to the printer.
•Allow for adequate overhead clearance for opening the top cover to allow easy access to the
labels tock and ink cartridge. The printer will require 7 inches (17.78 cm) of additional space
on the top side to completely open the cover (Total = 16.5" or 41.91 cm).
7
1B Unpacking and Inspection
While unpacking your printer, inspect the carton to ensure that no damage has occurred during
shipping. Make sure that all supplied accessories are included with your unit. The following items
are included in the supply box:
1. Power Adapter and Cord
2. 6’ USB Cable (If other USB cable is used, it must be 6’ (2 M) or less)
3. Color Dye Ink Cartridge Part Number 53496 (Pigment is also available –Part Number: 53491)
4. Printed documentation
5. Label roll holders (Assembly required –section 1C)
6. Large Roll Hub
7. Small Roll Hub
8. T8 Allen Key and two screws
2
1
3
5
6
7
8
5
5
8
1C Installing the Roll Holders
Some light assembly is required before operating the printer. Follow these instructions to install the
roll holders.
1. Set the printer on its front so the bottom is facing you.
2. Install the movable label roll holder by attaching the hooked end on the rail. The bottom of
the holder will fit in the notch on the printer.
Rail
Notch
Tab
Movable Roll Holder
Movable Roll Holder
9
3. Slide the Roll Holder to the far right.
4. Install the roll guide by attaching
the hooked end on the rail. The
bottom of the holder will fit in the
notch on the printer.
Notch
Roll Guide
Roll Guide
10
5. Slide the Guide to the stop.
6. Locate the remaining roll holder with the protruding wire. Connect the wire to the port on
the printer. Tuck the wire inside the cavity.
Stop
Wire
Push the wire
into the cavity
as you move the
holder closer to
the notch
Notch
Indice
Altri manuali Primera Etichettatrice
Primera
Primera DX850 Manuale utente
Primera
Primera Cyclone C-1000 Manuale utente
Primera
Primera LX400e Manuale utente
Primera
Primera LX810 Manuale utente
Primera
Primera LX200 Manuale utente
Primera
Primera LX810e Manuale utente
Primera
Primera LX500e Manuale utente
Primera
Primera LX400 Manuale utente
Primera
Primera LX3000e Manuale
Primera
Primera AP362 Manuale utente
Primera
Primera CX1000 Manuale
Primera
Primera RX900 Manuale utente
Primera
Primera LX500 Manuale utente
Primera
Primera Cyclone Manuale utente
Primera
Primera LX900e Manuale utente
Primera
Primera LP130 Manuale utente
Primera
Primera LX800 Manuale utente
Primera
Primera LX3000 Manuale utente
Primera
Primera LX900 Manuale utente
Primera
Primera AP550e Manuale
