Principal LED STREET WRAP Manuale utente

P-LED.com

325.227.4577

STREET WRAP™

INSTALLATION GUIDE

warranty

5P5L

GETTING STARTED

RED

Tube

LEDs

Rain

Shield

1.69"

1.38"

Inspect the boxes for damage and check the parts against the supplied parts list.

Note: Report damaged parts or shortages immediately to prevent job slowdown /stoppage to place of

purchase.

Refer to attached provided print and conrm job measurements.

Layout your job on paper, making note of Power Supply placement. Power Supplies can be placed

at the end of runs or side by side to power allowable linear footage in each direction.

COMPONENT IDENTIFICATION & REQUIRED TOOLS

MATERIALS

Housing PVC, UC and impact resistant

Lens (LED Tube) Polypropylene, UV and impact resistant

Mounting Clip Steel

Prole Dimensions w/ Mounting Clips Street Wrap 1.38”X 1.69”

STREET WRAP™

The LEDs come pre-installed in the 106.5” System.

Same for Blue, RGB and White. Numbers are based on a 60W Power Supply.

REQUIRED TOOLS

• 25' Measuring Tape

• 100' Measuring Tape Framing Square

• Square -1’

• Portable Rechargable Drill

-5/16" hexbit and unibit

-Masonry bits (If brick wall)

• Extension Cord

• Sawzall or Compound Saw Carpenter Pencil

• Caulk Gun

• Box Knife

• Wire Strippers

• Wire Snips

• Laser Tool or Chalk Line Substitute Fasteners for the Application if Applicable

LED SPECIFICATIONS

ELECTRICAL

CONTENTS

GREEN

0.65 3.38182.522.197

Input 12VDC

Maximum Load 60W OR 120W

Current at Max. Load 5A

Street Wrap Mounting Bracket Layout...........................................1

Installing Street Wrap into Mounting Brackets...........................2

How to Wire RGB Street Wrap............................................................3

Custom Cut to Fit End of Runs & Corners......................................4

Mounting Street Wrap on an Incline...............................................5

Frame Border Installation....................................................................6

Connecting Power Supplies...............................................................7

Testing Each Section.............................................................................8

Note: If job measurements do not correspond to provided drawing, call Principal LED immediately at

325-227-4577. Remember: No more than 90 modules per 60W Power Supply.

Following these few simple steps will ensure a successful installation each time.

Read all instructions, before starting installation.

STREET FIGHTER RGB™

STREET FIGHTER™

STREET FIGHTER COLORS™

LED TUBE

LED TRACK

PLTC

CABLE

RAINSHIELD

COUPLING

MOUNTING

BRACKET

ENDCAP

BRACKET

WIRE HOLE CORNER PIECE

W/mod W/ft LM/ft Mod/ft

ANGLE BRACKET

QWIK BOX™

STREET WRAP™ MOUNTING BRACKET LAYOUT

3.38182.52

1. Use a chalk line, gauge, laser level, or other means to be certain the run is straight, marking locations for

brackets.

Border/perimeter of sign cabinets should always have orientation of Street Fighter Wrap™ housing raised

lip outboard on vertical or diagonal. Orient brackets so that the drain holes will be on the bottom side of

the horizontal runs.

Install mounting brackets. Spacing will be no greater than 17.75”. Length for Standard, Mix-n-Match and

Specialty Street Wrap™ is 106.5”, RGB is 104”. Use pre-drilled wire hole mounting brackets at transformer

locations.

Install end bracket after housing

has been installed into previous

brackets by sliding over end to

ensure bracket is centered

between sections. Place mounting

brackets 3” on center from corners.

SEC. 1

Lens

LEDs

Rain

Shield

120 VAC

Note: This is correct bracket orientation.

Note: Track sections share a bracket at the ends to keep ends together and straight. There must be a space left between 106.5” plastic track sections (NOT LEDs) of 3/16”.

60W Power Supply

319.5”

106.5”

NOTE: MAXIMUM 3 UNITS PER 6OW POWER SUPPLY

TIP

END OF RUN

EQ.

SHARED BRACKET

EQ.

SHARED BRACKET

EQ. EQ.EQ. EQ.

EQ. EQ.EQ. EQ.EQ. EQ.

END OF A RUN

INSTALLING STREET WRAP™ INTO MOUNTING BRACKETS SEC. 2

Connect wires from one section to another using red butt splice wire connectors. No more

than 45 modules in a series.

Before hanging sections that have the power cable placed between them, cut a small notch

with dikes or other tool in the back of both housing sections to allow room for cable.

Lay the section being added on the mounting brackets. After making wire connections tuck

the wires and connectors BEHIND LED modules. Caulk notch.

Insert the top edge into the top bracket latch. Push the track housing in and roll top track

housing into mounting bracket bottom point. See Figure 1.

Bring Street Wrap™ sections close together by pushing sections together until LED modules

come together, but leave a 3/16" approximate expansion gap between plastic track sections.

Leave no gaps in the LEDs.

Install an End Cap at the beginning and end of runs with silicone. Silicone on top side only, so

water will drain out.

Finish by sliding a Coupling Rain Shield under the mounting bracket latch, over both sections.

Use a small amount of silicone on one side of rain shield to hold on.

Use a small screw driver to gently pry up the Mounting Bracket Latch to insert Rain Shield

under latch making certain it is rmly attached.

WIRE HOLE

BRACKET

NOTCH

Butt Splice Wire Connector

3/16”Approx. expansion gap

between plastic track sections

NOT LEDs.

Coupling

Rain Shield

Mounting

Screw

Roll into bottom

point of track

housing

Portion Fascia

Insert top, Bracket Latch

Raised

Caulk Under

Rain Shield

Caulk Top

& Corners End Caps

DO NOT HIT LENS TO INSTALL TRACK!

This will permanently damage the lens.

Figure 1

CUSTOM CUT TO FIT END OF RUNS & CORNERS SEC. 4

END OF A RUN

Remove LEDs before cutting track by sliding one or two modules out.

Measure, mark and cut Street Wrap™ to required length. Use a ne blade.

Add drain holes in the center, of the cut piece of track, before reinstalling the LED.

Reinstall modules to desired length.

HORIZONTAL CORNERS

OUTSIDE CORNERS INSIDE CORNERS

Low Voltage

Cable

Track

Mounting

Bracket

Mounting

Screw

1/4" Gap for expansion

These corners are square

cut and overlap slightly

to give a continuous look

at a distance and allow

for thermal expansion.

Low Voltage

Cable

Track Mounting

Bracket

Mounting

Screw

1/4" Gap for expansion

CORNER CONNECTIONS

HINT: THREAD END CAPS ONTO PLTC CABLE FBEFORE WIRE CONNECTIONS

BACK TO BACK

PLTC CABLE

7.00”

Insulate or remove unused wires at the end of

run to prevent shorting. Do not connect wires

together or to next circuit.

VERY IMPORTANT

PLTC: Power Limited Tray Cable.

End Cap with hole drilled for

cable attach with adhesive

End Cap with hole drilled for

cable attach with adhesive

END OF A RUN

MOUNTING STREET WRAP™ ON AN INCLINE SEC. 5

Coupling Rain Shield

When mounting Street Wrap™ on an incline or vertically, two things

must be prevented. First the Street Wrap™ must be kept from sliding

down, while still allowing for expansion/contraction with temperature

changes. Second, water must be sealed out since it will run down the

top of the Street Wrap™.

Seal the rain shield to the upper Street Wrap™ to keep

water from penetrating.

Do NOT seal the rain shield to the lower

Street Wrap™ since the Street Wrap™ will

expand/contract.

Caulk above (or crimp) ONE

bracket towards the middle of

each of the rest of the Street

Wrap™ to prevent it from sliding

while still allowing it to expand

and contract.

Drill 2 holes in the

end cap to allow

water to escape.

FRAME BORDER INSTALLATION SEC. 6

EXAMPLE: 104” x 196”

V-Notch

Caulk Under

Rain Shield

End Cap

& Notch

Use a screwdriver

if needed to insert

rain shield into the

bracket.

PL TC

Cable

Drain

Holes

Angle

Bracket

Add Drain Holes

on bottom of

Vertical Runs

End Cap

attach with

caulk Track

Mounting

Bracket

1/4" Gap for

expansion

Drain Holes

Low Voltage Cable

Cable Hole

Mounting Bracket

Angle Brackets

below vertical runs

to prevent sliding

Mounting

Screw

3 Brackets Per Street Wrap

BOTTOM RIGHT DETAIL, PROFILE VIEWBOTTOM LEFT DETAIL

TOP LEFT, TOP VIEW DETAIL BOTTOM RIGHT DETAIL, SIDE VIEW

Silicone

1/4" Gap Typ. for expansion

Eq. Eq.

3"3"

Always seal

drain holes

with

on verticals

when present.

Always ensure

drain holes are

on bottom side.

Add holes to the

center of a run

less than 8 feet.

End caps

attach with

Silicone.

CONNECTING TRANSFORMERS SEC. 7

Attach Qwik Boxes to available support member.

Attach power supplies inside of Qwik Boxes.

Install strain relief for low voltage wire.

Drill 1/2” hole through the fascia. A conduit tting can be installed so that conduit can be

used.

Insert low voltage wire into the hole and connect to LED. Fill hole with silicone sealant.

Note: Stop and make sure the supplied power supply is 277VAC rated

with any primary voltage supply greater than 120.

Note: Three 106.5”Street Wrap™ Border per 60W

Power Supply.

Side by side mounting location show below can

reduce primary and secondary wiring labor time.

VERY IMPORTANT: KEEP LOW VOLTAGE CIRCUITS ELECTRICALLY SEPARATE, DO NOT CONNECT TRANSFORMERS OR LEDs FROM

DIFFERENT 106.5” STREET WRAPS™ TOGETHER OR CONNECT MORE THAN THREE 106.5”STREET WRAPS™ TO A 60W POWER SUPPLY!

Primary 120VAC (IN)

Secondary 12VDC

Low Voltage (OUT)

Connect

Black and White

wires from

to120VAC

Connect

and

Low Voltage

wires from

Transformers

TO LEDS

Power Cable

Strain Relief

Fitting

Fascia

DO NOT

CONNECT 120

VOLTS TO LEDs.

LEDs ARE

12VDC ONLY!

12VDC

Low

Voltage

to LEDs

TESTING EACH SECTION SEC. 8

IMPORTANT: DO NOT SKIP THIS STEP. ALWAYS CHECK ALL LED LIGHTS BEFORE CONTINUING.

DO NOT APPLY 120V TO THE RED OR BLACK WIRES OR DIRECTLY TO THE LED MODULES.

Using the installed trasformers, supply power to the LED light chains by connecting a temporary 120V connection to

the black and white wires on the transformer to power the LED lights.

REMEMBER: BLACK AND WHITE WIRES ARE FOR 120V POWER IN, RED AND BLACK ARE FOR LOW-VOLTAGE POWER OUT.

2. Check to see if all LEDs are lit and working correctly.

If a module or section does not light up, is damaged, etc. —disconnect power and check connections or replace a

module by splicing in another.

P-LED.com

325.227.4577

REV20190806

Altri manuali per STREET WRAP

Indice

Altri manuali Principal LED Lanterna

Principal LED

Principal LED STREET WRAP FLEX BACK-BEND Manuale utente

Principal LED

Principal LED STREET WRAP FLEX SIDE-BEND Manuale utente

Manuali Lanterna popolari di altre marche

KYOWA

KYOWA KW-9114 Manuale utente

Stahl

Stahl ECOLUX 6610 Series Manuale utente

SNOWJOE

SNOWJOE SUNJOE 24V-LGT500-CT Manuale utente

PRG

PRG VARI LITE VL5 Manuale utente

Raytec

Raytec VARIO2 series Manuale utente

ENSA

ENSA LEDBT18WS2 Manuale utente

LUG

LUG OFFICE LB LED N/T Manuale utente

GE Wallighter 250 Manuale utente

Draper

Draper RLEDL19/B Manuale utente

Green Lighting

Green Lighting TRI-SENSOR GL4612LU Manuale utente

Panasonic

Panasonic EY3741B57 Manuale utente

Clas Ohlson

Clas Ohlson LCC8T Manuale utente

Coolon

Coolon WDN-140 Manuale utente

Holiday Travel

Holiday Travel 834873 Manuale utente

BEGA

BEGA 84 036 Manuale utente

BEGA

BEGA 33 596 Manuale utente

Dale Tiffany

Dale Tiffany GT701162 Manuale utente

Wagan

Wagan Brite Nite Pop-Up USB Lantern Manuale utente