Prismatibro Prisma Light Eliott Manuale utente
MOUNTING AND INSTALLATION
MANUAL
2Prisma Light | prismatibro.se
PRODUCT DESCRIPTION Prisma Light Eliott is a luminaire produced in
Sweden for street light with LED-technology.
Add: pole tting and cable.
AREA OF USE Outdoors: Main roads, urban roads,
bicycle paths, parking lots, industrial areas,
skiing tracks.
MOUNTING HEIGHT Up to 15 meters
WEIGHT 5,4 kg excluding pole tting
MEASUREMENTS
Length 565 mm
Width 230 mm
Height with bird spikes Flat glass: 221 mm • Curved glass: 261 mm
Height with plugs Flat glass: 152 mm • Curved glass: 192 mm
Height with plane case Flat glass: 120 mm • Curved glass: 160 mm
WIND RESISTANCE AREA
Plane case, at glass 0,058 m2
PRODUCT FACTS
3
prismatibro.se | Prisma Light
12 °
Pole top
Mounting
The tting is mounted on the pole and the two screws are tightened
Using torque: 8Nm +/- 2 Nm.
INSTALLATION
Tools
Hex screw, size 6: Pole tting - Housing
Hex screw, size 4: Pole tting - Pole
Pole tting
There are two dierent ttings, the one you choose is mounted upon delivery.
One adjustable. One with a xed angle.
See pictures below.
Fixed angle
Adjustable
Adjustable, reversible to t both pole top and arm.
Delivered with the tting mounted in the desired position for mounting.
That is way it is two item numbers for the same tting.
±10 °±10 °
Item
353-0011
Item
353-0004
Item
353-0003
4Prisma Light | prismatibro.se
Only 230 V
• Prisma Light Eliott Constant
• Prisma Light Eliott Remote
• Prisma Light Eliott Detect
The luminaire should not be mounted or demounted with power on.
Supply voltage 110-230 V AC, 50 Hz.
Wattage 5-90W depending on model
1. Mount the luminaire on the pole, adjust if necessary.
2. Connect the cable in the fuse holder.
3. Make sure that the Neutral-connection is connected properly.
If not done correctly, this may cause uncontrolled voltage in
the installation.
4. Turn the power on.
ELECTRICAL INSTALLATION
5
prismatibro.se | Prisma Light
Prisma Light Remote
DEPLOYMENT
• Power on the luminaire.
• Prisma Light Eliott should now have
the factory setting that the customer
wanted when ordered.
• Prisma Light Eliott has a circuit board
with built in IR-communication.
Prisma
USE
• The settings are changed
with a remote control.
Instructions on next page.
Manual can also be
downloaded from:
www.prismatibro.se
DEPLOYMENT AND USE
Prisma Light Constant
• The luminaire is equiped with a driver with a xed level. The setting will
be made at the factory and can only be changed at the factory in Tibro.
Prisma Light Detect
DEPLOYMENT
• Power on the luminaire
When it starts up the luminaire will blink as it calibrates.
Before it is programmed by the customer -see installation manual control
systems - the luminaire will be att 40% when there is no detection and
50% at detection.
At this stage it doesn’t communicate with other luminaries.
CONTROL SYSTEMS
MANUAL
6Prisma Light | prismatibro.se
GATEWAY INSTALLATION
Light cabinet
The gateway should be installed within 30 meters from the closest
Detect-luminaire.
The gateway will communicate wirelessly with the luminaries.
The installation should be done by the manufactorer or by someone
educated by the manufactorer.
* The installer should contact the producer of the light cabinet to get
the correct instruction about making holes in the light cabinet.
1Drill a hole for the power cable, Ø 20 mm*
2Rubber gasket:
Add the rubber gasket to the backside of the Gateway.
3Connect the power cable to the backside of the Gateway:
Press down the coupling ring, and keep turning the ring
(clock wise) until you feel a
”click”. Now the connector
is locked.
4Mount the Gateway to
the light cabinet - use
the supplied screws.
1
4
3
2
7
prismatibro.se | Prisma Light
GATEWAY INSTALLATION
Light pole
The gateway should be installed within 30 meters from the closest
Detect-luminaire.
The gateway will communicate wirelessly with the luminaries.
The installation should be done by the manufactorer or by someone
educated by the manufactorer.
1Drill a hole, Ø 20 mm, for the power cable on the light pole
at prefered height.
2Use the pole adaptor to drill the two mounting holes with a
Ø 3,5mm drill.
3Mount the adaptor:
Use the supplied screws
4Connect the power cable to backside of the Gateway:
Press down the coupling ring, and keep turning the ring (clock wise)
until you feel a ”click”. Now the connector is locked.
5Mount the Gateway:
Use the supplied screws.
1
2
5
43
The LED in the luminaire should only be changed by qualied personnel.
The circuit board can only be changed by demounting the entire luminaire.
If you open the casing, the IP-classication is at risk. If a problem appears,
return the entire luminaire and we will solve the problem.
Cleaning Wash with water at low pressure.
Do not use high pressure washer.
SERVICE AND MAINTENANCE
TROUBLESHOOTINGWARRANTY
RECYCLING AND PACKAGING
If a problem appears, return the
entire luminaire and we will solve
the problem.
For complete warranty terms visit our
website www.prismatibro.se or call
+46 504-400 40 or send an e-mail to
support@prismatibro.se
The packaging material is reuseable and/or recyclable.
More help!
prismatibro.se/en/error-el/
Or scan the QR-code
This and other documents
can be downloaded from
prismatibro.se/en
the QR-code will
take you there.
DOWNLOAD DOCUMENTS
Indice
Altri manuali Prismatibro Lanterna
