Pro1 Technologies T955 Manuale utente

Operation ManualOperation Manual

U.S. Registered Trademark. Patents pending

T955WH

Pro1 Technologies

Toll Free: 888-776-1427

Web: www.pro1iaq.com

Hours of Operation: M-F 9AM - 6PM Eastern

Table of Contents

Thermostat Operation

Thermostat Quick Reference

Setting the Humidity

Programming

Features

Warranty Information

Page

2-3

4-7

10-16

Una version en español de este

manual se puede descargar en la

pagina web de la compañia.

Equipment damage hazard.

Do not operate the cooling

system if the outdoor

temperature is below 50 ˚F

(10 ˚C) to prevent possible

compressor damage.

Caution

Rev. 1845

17-18

8-9

P.O. Box 3377

Springeld, MO 65808-3377

Thermostat OperationThermostat Operation

LCD Display Glow in the dark light button

Fan Key

System Key

Temperature Setpoint Buttons

See page 4 for details about

this display read out.

The glow in the dark light

button will self illuminate

for several hours after

exposure to ambient light.

This button turns on the

display light when pressed.

Select ON or AUTO. The ON

key will run the fan

continuously. The AUTO key

will cycle the fan on only

when the heating or cooling

system is on. A Note About

Programmable Fan: The

programmable fan feature will run the

fan continuously during any time

period it is programmed to be on. This

is the best way to keep the air

circulated and to eliminate hot & cold

spots in your building.

Selects the operation mode of

your HVAC system. Selecting

HEAT turns on the heat mode.

Selecting COOL turns on the

air conditioning mode.

Selecting OFF turns both

heating and cooling o.

Selecting AUTO will turn the

HEAT or COOL on as needed.

Press the or

buttons to select the

desired room temperature.

Menu Key

Use this key to set up your

programming options.

Refer to page 10 for

instructions.

7Humidity Key

Use this key to enter the

target humidity setpoint

screen. Refer to page 8 for

instructions.

Next Zone

Use this key for

programming or to

navigate to multiple zones

if using indoor remote

sensors.

Temperature

Set Time

Next Zone

Clean

Display

Humidity

Thermostat Quick Reference Thermostat Quick Reference

Indicates the current room temperature

Time and day of the week

REMOTE indicates a remote has control of the system.

System Operation Indicators: The COOL, HEAT or FAN icon will display

when the COOL, HEAT or FAN is on. NOTE: The compressor delay feature is

active if these icons are ashing. The compressor will not turn on until the 5

minute delay has elapsed.

Setpoint: Displays the user selectable setpoint temperature

HOLD is displayed when thermostat program is permanently overriden.

Low Battery Indicator: Replace batteries when this indicator is shown.

Program Menu Options: Show dierent options during programming.

Period Icons - This thermostat can have 2 or 4 programmable time periods

per day. Icons are displayed for 4 time periods. Occupied and Unoccupied

will display in the text eld for 2 time periods.

1Humidity: Shows the humidity target setpoint settings and keys.

Clean Display: Pressing CLEAN DISPLAY will allow 30 seconds to clean

the display. The keys will be inoperable during this time. CLEAN will appear

if your contractor has programmed a lter change reminder. Press and hold

CLEAN when lter has been replaced to reset the lter change reminder

timer.

12 Next Zone: This button will appear if optional indoor remotes are

present. By selecting NEXT ZONE you can cycle through each of the zones

set up during the initial installation and programming.

3System Information: Shows several dierent informational functions.

Thermostat Quick Reference Thermostat Quick Reference

The low battery indicator is displayed when the AA battery

power is low. If the user fails to replace the battery within 21

days, the screen will only show the low battery indicator but

maintain all functionality. If the user fails to replace the batteries

after an additional 21 days (days 22-42 since rst “low battery”

display) the setpoints will change to 55˚F (Heating) and 85˚F

(Cooling). If the user adjusts the setpoint away from either of

these, it will hold for 4 hours then return to either 55˚F or 85˚F.

After day 63 the batteries must be replaced immediately to

avoid freezing or overheating because the thermostat will shut

the unit o until the batteries are changed.

Important:

Battery Door Information

When the battery icon appears replace your AA

batteries immediately. Failure to do so may result in your

heating & cooling system becoming inoperable.

Freezing or overheating can occur.

Caution:

Insert 2 AA Alkaline batteries

(included). High quality alkaline

batteries are recommended.

Pull the thermostat directly away from the wall to access the

batteries. A rm tug will be required to remove the thermostat from

the subbase mounted on the wall.

Setting The Humidity Setting The Humidity

Setting The Humidity

Follow the steps below to change your

target humidity setpoint.

Press the humidity button.

Use the or

button to select the target

humidity setpoint.

Press DONE when completed.

Target humidity setpoint keys

Note:

The target humidity setpoint is not

programmable. Unlike temperature,

humidity does not change quickly

and should not be programmed.

Note:

Humidity is only energized during

heat. Dehumidity is only energized

during cool. Heat and cool each have

their own target setpoints.

Ambient Humidity Display

Ambient humidity will ash opposite the day and time. If the optional

outdoor temperature sensor is installed the ambient outdoor temperature

will also cycle in the display.

39 Humidity %

39Humidity % AM

Mon

OUTDOOR

Ambient Humidity Day & Time Outdoor Temperature

Increasing Humidity

The table on the right shows

recommended indoor humidity

levels in relation to outdoor

temperatures during heating

(adding humidity).

Outside

Temperature (0°)

Recommended

Relative Humidity

+20° and above

+10°

0°

-10°

-20°

35% to 40%

30%

25%

20%

15%

Consult your professional HVAC

technician for recommended

settings for your climate.

Temperature

Next Zone

Humidity

Humidity Key

Programming Programming

Set Time

Follow the steps below to set the day of the week and current time:

1. Press the MENU button.

2. Press SET TIME.

3. Day of the week will be ashing. Use the or key to

select the current day of the week.

4. Press Next Step.

5. The current hour is ashing. Use the or key to

select the current hour. When using 12-hour time, make sure

the correct a.m. or p.m. choice is selected.

6. Press Next Step.

7. Minutes are now ashing. Use the or key to

select current minutes.

8. Press DONE when completed.

Set 5+1+1 Program Schedule

You will see a TECHNICIAN SETUP option after the MENU key

is pressed. This TECHNICIAN SETUP key is for installer

conguration and should NOT be changed unless you consult

your professional heating and air conditioning technician.

Important:

1. Select HEAT or COOL with the system key.

Note: You have to program heat and cool each separately.

2. Press the MENU key.

3. Press SET SCHEDULE. Note: Monday-Friday is displayed and the

WAKE or OCCUPIED icon is shown. You are now programming

that time period for the weekday setting.

To customize your 5+1+1 Program schedule, follow these steps:

Weekday:

Additional step if indoor remote sensor is connected.

The master thermostat will either average all sensors (system average)

or only use one sensor for the system ambient temperature (priority).

The default setting is SYSTEM AVERAGE, which means all sensors are

averaged to create the system average ambient temperature reading.

The NEXT ZONE key can be pressed to change the priority. The system

information area of the display shows the priority. For Example: There is

a remote connected and it is named REMOTE 1. If the NEXT ZONE key is

pressed until REMOTE 1 is shown, then the REMOTE 1 ambient

temperature reading will be used exclusively for that time period. All

other sensors will be ignored.

Continued on next page...

Set 7 Day Program Schedule

Programming Programming

A Note About Auto Changeover:

When in Auto you have the ability to switch between auto heat or auto

cool by pressing the system key. This can be done once the current

mode has reached its setpoint. For example: if in auto heat, the heat

setpoint must be satised before the thermostat will allow you to switch

to auto cool. You can switch out of auto by holding down the system

key. To get back into auto, you must toggle the system key to auto.

1. Select HEAT or COOL with the SYSTEM key.

Note: You have to program heat and cool each separately.

2. Press the MENU key.

3. Press SET SCHED. Note: Monday is displayed and the

WAKE or OCCUPIED icon is shown. You are now programming

the WAKE or OCCUPIED time period for that day.

Monday:

4. Use the or key to make your time

selection for the weekday time period.

Note: If you want the fan to run continuously during this time

period, select ON with the FAN key.

5. Then use the or key to make your setpoint selection for

that weekday period.

6. Press Next Step.

7. Repeat steps 4 through 6 that day’s other time periods.

Repeat steps 4 through 6 for Saturday time periods.

Saturday:

Repeat steps 4 through 6 for Sunday time periods.

Sunday:

Additional step if indoor remote sensor is connected.

The master thermostat will either average all sensors (system average)

or only use one sensor for the system ambient temperature (priority).

The default setting is SYSTEM AVERAGE, which means all sensors are

averaged to create the system average ambient temperature reading.

The NEXT ZONE key can be pressed to change the priority. The system

information area of the display shows the priority. For Example: There is

a remote connected and it is named REMOTE 1. If the NEXT ZONE key is

pressed until REMOTE 1 is shown, then the REMOTE 1 ambient

temperature reading will be used exclusively for that time period. All

other sensors will be ignored.

Continued on next page...

Programming Programming

The NEXT ZONE key cycles through all sensors connected to your

wireless system.

SYSTEM AVERAGE shows the average ambient temperature of all

connected sensors.

LOCAL shows the ambient temperature of the thermostat only.

The name of the remote sensor will show and the ambient

temperature for that sensor will be displayed.

For more information please refer to the Indoor Remote Sensor User

Guide.

Next Zone (Only if indoor remote is connected)

4. Use the or key to make your time selection for that days

time period. Note: If you want the fan to run continuously during

this time period, select ON with the FAN key.

5. Then use the or key to make your setpoint selection for

that days time period.

6. Press Next Step.

7. Repeat steps 4 through 6 for that day’s other time periods.

Repeat steps 4 through 7 for the remaining days of the week.

The programmable fan feature will run the fan continuousy during

any time period it is programmed to be on. This is the best way to

keep the air circulated and to eliminate hot & cold spots in your

building.

A Note About Programmable Fan

Programming Features

If appears in the display, then the keypad is locked. All or some of

the keys will not work. Hold the and keys for 3 seconds to

remove the lock. Use the same procedure to lock the display

Keypad Lockout Note: Temporary Hold: The thermostat will display HOLD and Run Sched-

ule on the bottom of your screen when you press the or

key. If you do nothing, the temperature will remain at this setpoint

temporarily for 4 hours. After this, the program setpoint will then

replace your temporary setpoint.

Permanent Hold: With a temporary hold set, if you press the HOLD

key at the bottom of your screen, you will see HOLD appear next to

the setpoint temperature in the display. The thermostat will now

permanently stay at this setpoint and can be adjusted using the

or keys.

To Return To Program: Press the Run Schedule key at the bottom of

your screen to exit temporary and permanent holds.

Temporary & Permanent Hold Feature

Altri manuali per T955

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Pro1 Technologies Termostato

Pro1 Technologies

Pro1 Technologies T721i Manuale utente

Pro1 Technologies

Pro1 Technologies T955 Manuale utente

Pro1 Technologies

Pro1 Technologies T801 Manuale utente

Pro1 Technologies

Pro1 Technologies T755WHO Manuale utente

Pro1 Technologies

Pro1 Technologies T805 Manuale utente

Pro1 Technologies

Pro1 Technologies T955WH Manuale utente

Pro1 Technologies

Pro1 Technologies T701i Manuale utente

Pro1 Technologies

Pro1 Technologies T771 Manuale utente

Pro1 Technologies

Pro1 Technologies T721i Manuale utente

Pro1 Technologies

Pro1 Technologies T605-2 Manuale utente

Pro1 Technologies

Pro1 Technologies T621-2 Manuale utente

Pro1 Technologies

Pro1 Technologies T701i Manuale utente

Pro1 Technologies

Pro1 Technologies RZ251W Manuale utente

Pro1 Technologies

Pro1 Technologies T731W Manuale utente

Pro1 Technologies

Pro1 Technologies T721i Manuale utente

Pro1 Technologies

Pro1 Technologies T855SH Manuale utente

Pro1 Technologies

Pro1 Technologies T625-2 Manuale utente

Pro1 Technologies

Pro1 Technologies T705 Manuale utente

Pro1 Technologies

Pro1 Technologies T955S Manuale utente

Pro1 Technologies

Pro1 Technologies T725 Manuale utente

Pro1 Technologies

Pro1 Technologies T631-2 Manuale utente

Pro1 Technologies

Pro1 Technologies RZ251W Manuale utente

Pro1 Technologies

Pro1 Technologies T621-2 Manuale utente

Pro1 Technologies

Pro1 Technologies T731 Manuale utente

Manuali Termostato popolari di altre marche

EWELLY

EWELLY EW-181 Manuale utente

Prolon

Prolon T1100 Istruzioni per l'installazione

Computherm

Computherm Q20 Manuale utente

Heatmiser

Heatmiser neoStat Manuale utente

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manuale utente

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manuale utente

Saswell

Saswell SAS920XWHB-7-S-RF Guida

Aircalo

Aircalo TFP1-ET85P2 Manuale utente

Honeywell

Honeywell CM721 Manuale utente

Carrier

Carrier DEBONAIR 33CS Manuale utente

Lennox

Lennox iHarmony Zone Thermostat Istruzioni per il montaggio

Gemtech

Gemtech GT7000 Manuale di istruzioni

Rollei

Rollei Smartes 45000 Manuale utente

Sinope

Sinope TH1300RF Manuale utente

Honeywell

Honeywell RLV4305 Manuale utente

Honeywell

Honeywell Prestige 2.0 THX9421 Manuale utente

NuTone

NuTone NTBZ48 Istruzioni operative originali

Stelpro

Stelpro MAESTRO ASMT402AD Manuale utente