Probe PMA-H2000 Manuale utente
In/Outdoor Camera
HD-SDI PTZ
Ver. 0.6 / 2011.04
User’s Manual
Safety Information
This symbol indicates that dangerous voltage
consisting a risk of electric shock is present within
this unit.
Warning Precaution
This exclamation point symbol is intended to alert the
user to the presence of important operating and
maintenance (servicing) instructions in the literature
accompanying the appliance.
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION:
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN.
To prevent damage which may result in fire or electric shock
hazard, do not expose this appliance to rain or moisture.
Be sure to use only the standard adapter that is specified in
the specification sheet. Using any other adapter could cause
fire, electrical shock, or damage to the product.
Incorrectly connecting the power supply or replacing battery
may cause explosion, fire, electric shock, or damage to the
product.
Do not connect multiple cameras to a single adapter.
Exceeding the capacity may cause abnormal heat generation
or fire.
Securely plug the power cord into the power receptacle.
Insecure connection may cause fire.
When installing the camera, fasten it securely and firmly.
A falling camera may cause personal injury.
Do not place conductive objects (e.g. screw drivers, coins,
metal things, etc.) or containers filled with water on top of
the camera. Doing so may cause personal injury due to fire,
electric shock, or falling objects.
Do not install the unit in humid, dusty, or sooty locations.
Doing so may cause fire or electric shock.
If any unusual smell or smoke come from the unit, stop
using the product. In such case, immediately disconnect the
power source and contact the service center. Continued use
in such a condition may cause fire or electric shock.
If this product fails to operate normally, contact the nearest
service center. Never disassemble or modify this product in
any way.
When cleaning, do not spray water directly onto parts of the
product. Doing so may cause fire or electric shock.
WARNING
WARNING
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
Precautions
Operating
t Before using, make sure power supply and others are
properly connected.
tWhile operating, if any abnormal condition or malfunction
is observed, stop using the camera immediately and then
contact your Special dealer.
Handling
tDo not disassemble or tamper with parts inside the camera.
tDo not drop or subject the camera to shock and vibration as
this can damage camera.
tCare must be taken when you clean the clear dome cover.
Especially, scratch and dust will ruin your quality of camera.
Installation and Storage
tDo not install the camera in areas of extreme temperature,
which exceed the allowable range.
tAvoid installing in humid or dusty places.
tAvoid installing in places where radiation is present.
tAvoid installing in places where there are strong magnetic
elds and electric signals.
tAvoid installing in places where the camera would be subject
to strong vibrations.
tNever expose the camera to rain and water.
Important Safety Instructions
1. Read these instructions. - All these safety and operating instructions should be read before the product is operated.
2. Keep these instructions. - The safety, operating and use instructions should be retained for future reference.
3. Heed all warnings. - All warnings on the product and in the operating instructions should be adhered to.
4. Follow all instructions. - All operating and use instructions should be followed.
5. Do not use this apparatus near water. - For example: near a bath tub, wash bowl, kitchen sink, laundry tub, in a
wet basement; near a swimming pool; etc.
6. Clean only with dry cloth. - Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. - Slots and
openings in the cabinet are provided for ventilation, to ensure reliable operation of the product, and to protect it
from over-heating. The openings should never be blocked by placing the product on bed, sofa, rug or other similar
surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper
ventilation is provided and the manufacturer’s unstructions have been adhere to.
8. Do not install near any heat sources such as radiators, heat registers, or other apparatus (including ampliers)
that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with
one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade
or the third prong are provided for your safety. If the provided plug does not t into your outlet, consult an
electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and
the point where they exit from the apparatus.
11. Only use attachments/accessories specied by the manufacturer.
12. Use only with cart, stand, tripod, bracket, or table specied by the
manufacturer, or sold with the apparatus. When a cart is used, use
caution when moving the cart/apparatus combination to avoid
injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualied service personnel. Servicing is required when the apparatus has been damaged
in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been
dropped.
Disposal of Your Old Appliance
1. When this crossed-out wheel bin symbol is attached to a product it means the product is covered by
the European Directive 2002/96/EC.
2. All electrical and electronic products should be disposed of separately from the municipal waste
stream via designated by the government or the local authorities.
3. The correct disposal of your old appliance will help prevent potential negative consequences for
the environment and human health.
4. For more detailed information about disposal of your old appliance, please contact your city oce,
waste disposal service or the shop where you purchased the product.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user
will be required to correct the interferenece at his own expense.
Contents
6
7
Product & Accessories
Parts Name & Functions
4 Precautions
1. Introduction
8
9
10
11
12
13
Installation Using Surface Mount Bracket
Installation Using Flush Mount Ring Bracket(Option)
Installation Using Ceiling Mount Bracket(Option)
Installation Using Wall Mount Bracket(Option)
Installation Using Wall Mount Bracket with Junction Box(Option)
Terminal Block
2. Installation
14
15
16
17
18
19
20
22
23
24
25
Check Points before Operation
OSD -
ROOT MENU & SYSTEM INFORMATION
OSD -
MOTION SETUP
OSD -
FUNCTION SETUP > PRESET SETUP
OSD -
FUNCTION SETUP > SCAN SETUP
OSD -
FUNCTION SETUP > PATTERN SETUP
OSD -
FUNCTION SETUP > GROUP SETUP
OSD -
CAMERA SETUP > WB SETUP
OSD -
CAMERA SETUP > AE SETUP
OSD -
CAMERA SETUP > OTHER SETUP
OSD -
SYSTEM SETUP
3. OSD Menu
26
27
Dimensions
Dimensions of Option Brackets
4. Specification
Product & Accessories
Introduction -
1
Main Body
Camera module, screws, terminal block slot and DIP
switches are included.
Surface Mount Bracket
- It is used when installing the camera right on to the
ceiling.
- To install the camera with the surface mount bracket,
the bracket needs to be separated from the main body,
then needs to be re-assembled the bracket and the
main body according to the order.
Screw & Plastic Anchor
- Screws are used to fix the surface mount bracket to
the ceiling.
- Plastic anchors are used to tighten the screws to the
hole by inserting them into the holes in advance.
Terminal Block
Power, video, communication and alarm input cables
are connected through the terminal blocks.
Torx Wrench
It is used to screw/unscrew the fixed screws on the
main body.
Rubber Gasket
It is installed between the surface mount bracket and
wall/wall mount bracket to prevent the water leakage.
Manual CD
It is included Manual and ‘IP Search’ program.
Quick Manual
It gives a concise explanation of the installation of
Camera.
Please check if all the camera and
accessories are included in the package.
2
1
5
3
4
8
6
7
IN2
POWER
IN1
COM
VIDEO OUT
9P Terminal Block
4
Main Body + Surface Mount Bracket
21
Rubber Gasket
6
Quick Manual
Screw & Plastic Anchor-4pcs
3
Manual CD
7
Torx Wrench
5
User’sManual
Speed Dome Camera
Anti-vandal
HD
x
10
8
Part Name & Functions
Introduction -
1
Dome Cover
-
Protects the camera module from outside environment.
- Do not detach protection film from the dome cover
before finishing all installation processes to protect
dome cover from scratches or dust.
Lockup Screw
Fixes main body to the surface mount bracket.
Fan
Fan for temperature control.
HD-SDI Cable
Main video output cable.
9P Terminal Block Slot
Power, keyboard controller, Alarm input and relay out
cables are connected to this terminal block.
LED & Reset Button
LED for active(yellow light), power(red light) status
and Reset button for reset camera.
ID Setup Switch
Specify the camera ID.
Mounting Hole
This is used to attach the surface mount bracket to the
ceiling.
¾” Pipe Mounting Hole
- This is used to pass the cables to the cameras.
- When water protection is needed, connect the ¾” pipe
through this hole, then pass the cables through the
pipe.
2
1
5
3
4
6
7
8
9
Main Body
1
2
Bottom of Main Body
3
4
5
7
8
9
6
Installation Using Surface Mount Bracket
Installation -
2
Drilling the Hole on the Ceiling
Fix the Main Body
Connect Wire the Cables,
Terminal Blocks
Detach the Protection Film
Fix the Surface Mount
Bracket
2
Drilling the Hole on the Ceiling
To pass cables through the ceiling, drill a hole (30mm
diameter) on the ceiling panel.
Fix the Surface Mount Bracket
Pass the cables to the ¾” pipe hole, and screw the surface
mount bracket to the ceiling.
Rubber Gasket
- Before installing the gasket, the hole in the center is
to be cut by knife when only necessary.
- When installing gasket, the protrusion of the gasket
should be matched with the groove joint of the bottom
of the surface mount bracket.
Connect Wire the Cables, Terminal Blocks
Connect the terminal blocks to the main body.
See the section 2 ‘Installation-Terminer Block’ for detail.
Fix the Main Body
Screw the main body to the surface mount bracket by
screwing 4 lock-up screws.
Detach the Protection Film
Detach the protection film from the dome cover.
2
1
3
5
4
2
1
5
3
4
Rubber Gasket
Installation Using Flush Mount Ring Bracket (Option)
Installation -
2
Drilling the Hole on
the Ceiling
Fix the Main Body
Connect Wire the
Cables and
Terminal Blocks
4
Fix the Flush Mount
Ring Bracket to the
Main Body
3
Separate the
Lock-up Screws
from the Main Body
2
2
3
4
5
1
2
1
5
3
4
6
Drilling the Hole on the Ceiling
To pass cables through the ceiling, drill a hole(70mm
diameter) on the ceiling.
Separate the Lock-up Screws from the Main Body
Separate the 4 lock-up screws from the main body in
advance.
Fix the Flush Mount Ring Bracket to the Main Body
Fix the flush mount ring bracket to the main body
using torx screws.
Connect Wire the Cables, Terminal Blocks
- Connect the terminal blocks to the main body.
- Refer the previous page for detailed information.
Fix the Main Body
Screw the main body with the surface mount bracket
to the ceiling using the screws on the surface mount
bracket.
Detach the Protection Film
Detach the protection film from the dome cover.
Installation Using Ceiling Mount Bracket (Option)
Installation -
Rubber Gasket
Rubber Gasket
2
Connect Wire the
Cables and
Terminal Blocks
Fix the Surface
Mount Bracket
Fix the Ceiling
Mount Bracket
2
3
4
5Fix the Main Body
6Detach the
Protection Film
2
1
2
1
5
3
4
6
Drill the Ceiling and Fix the Anchor Bolts
On the ceiling, drill a hole (6mm diameter/ 50mm depth),
and fix the anchor bolts.
Fix the Ceiling Mount Bracket
1.
Drill a hole (20mm diameter) on the pipe of the bracket
to pass the cables.
2. On the fixed anchor bolts, attach the rubber gasket
and screw the ceiling mount bracket.
Drill the Ceiling
To pass cables to upside of ceiling, drill a hole (30mm
diameter) on the ceiling.
Fix the Ceiling Mount Bracket
Pass the cables into the ceiling mount bracket, and
screw the ceiling mount bracket to the ceiling.
Fix the Surface Mount Bracket
Pass the cables through the hole of the surface mount
bracket, screw the surface mount bracket to the ceiling
mount bracket.
Connect Wire the Cables, Terminal Blocks
- Connect the terminal blocks to the main body.
- Refer the 8 page for detailed information.
Fix the Main Body
Screw the main body to the surface mount bracket.
(Screws are included in the main body.)
Detach the Protection Film
Detach the protection film from the dome cover.
1. Installing on the Concrete Ceiling
2. Installing on the Wooden Ceiling
Drill the Ceiling and
Fix the Anchor Bolts
1
Indice
Altri manuali Probe Telecamera di sicurezza
