ProfiDrum 65 Manuale utente
ProfiDrum Page 1 van 20 © 2013
User Manual
Manufacturer information:
ProfiDrum
Lopik
Tel: +31 (0) 348-551801
www.profidrum.com
ProfiDrum Page 2 van 20 © 2013
Index
Introduction 3
Adjustments 3
Factory information 4
Contents of the package 4
Profile drumfilter 5
Connection to supply and drain pipes 6
Pump-fed arrangement 8
Connecting the waste disposel container on the sewer 10
Connecting the high pressure pump and spraybar 11
Controlbox 13
Connecting engines 10
Standard controlbox with opened case 14
Adjusting level probes and low water protection 16
Managing the controlbox 16
Test run after connecting the components 17
Intervals between rinses 17
Maintenance 17
Statement of marked points 17
Disclaimer 18
Important safety warnings 18
Final accountability 19
ProfiDrum Page 3 van 20 © 2013
Introductie
Congratulations with the purchase of your ProfiDrum filter!
With the purchase of this drum filter you now own a high quality product which
was built with the utmost care and precision.
Please read carefully and follow all instructions and tips before you install the
drum filter.
If you have any questions, please do not hesitate to contact your dealer.
This manual is a simple guide to installing your drum filter.
We recommend making a copy of the manual to keep in the immediate vicinity of
your drum filter.
Our drum filters are suitable for gravity-or pump-fed lines.
Adjustments
Drum filters are in collaboration and marked with independent consultancy
Euronorm BV, CE.
Adjustments to Profi Drum drum filters that are made without the prior permission
of the manufacturer are not covered by the guarantee. When adjustments are
done without permission the CE marking,and guarantee expire.
Use only original spare parts supplied by us for repairs.
Spare parts can be ordered from the manufacturer or your dealer.
ProfiDrum Page 4 van 20 © 2013
Factory information
You can find the type / model designation on the rating plate of your drum filter.
EC declaration
Manufacturer
ProfiDrum Holland
Sluisweg 5
3412 LA Lopik
Model Type: ProfiDrum 45/55/65/65E/75E
ProfiDrum model designation on the label on the drum filter
Applied CE Directives:
- New Machinery Directive (2006/42/EC)
- Low Voltage Directive (2006/95/EC)
- EMC Directive (2004/108/EC)
Applied standards:
- NEN-EN-ISO 12100-1
- NEN-EN-IEC 60204-1
The manufacturer declares to have complied with the safety requirements which
are determined from the safety requirements of the Machinery Directive. This
product also overlaps with the safety requirements from the LVD and EMC
directives.
Contents of the package
Your drumfilter is supplied with automatic control.
On all models a standard high pressure pump is supplied.
ProfiDrum Page 5 van 20 © 2013
Profile drumfilter
1 Drummotor
2 Sensor
3 By-Pass
4 Waste disposel
5 Water imports, from pond
6 Water exports, to pump(s)
7 Drum with panels
8 Nozzles
9 Seal
ProfiDrum Page 6 van 20 © 2013
Connecting your drumfilter in GRAVITY arrangement
Place the drum filter on a solid surface that is completely level. You can then
connect the supply and return pipes * 1 of the drum to the pond or your filter. They
easily connect with sleeves and / or bends with a collar, or a rubber sock. The
size of the required PVC materials is 110 mm. It is advisable to place the landing
on the front side of the drum filter to provide a slide valve. Note: Always switch
off the control!
Set the drum so that the water level is even with the top of the silicone sealing
strip. By setting the water level at this height you use the most surface are of the
screen of the drum filter.
Water level adjustment
If you do not have enough supply piping, or the bends in the piping cause too
much resistance, there is the option to place the drum in such a way that the
water level is slightly above the top of the silicon strip (gravity situation) state.
Please note that all pumps are off.
ProfiDrum Page 7 van 20 © 2013
GRAVITY arrangement, not flush situation, probe touches water
GRAVITY arrangement, flush situation, probe is dry
Darkblue is not filtered water.
Blue is filtered water.
ProfiDrum Page 8 van 20 © 2013
Pump-fed arrangement
1. Place the drum mesh tray on a solid surface that is completely level.
2. Connect a number of inputs to the front of the drum filter.
3. Then connect the pump(s) to one of the remaining input(s). If necessary,
you have to get an adapter to the connector of the pump you are using.
4. Then, extend the outputs on the back of the drumfilter in such a way that
the top of the outflow bend is at the same height of the top of the horizontal
beam at the front. Move the probe level of the back of the drum to the front
side of the drum in the collecting compartment.
ProfiDrum Page 9 van 20 © 2013
Pump-fed arrangement, not flush situation, probe is dry
Pump-fed arrangement, not flush situation, probe touches water
ProfiDrum Page 10 van 20 © 2013
Connecting the waste disposel container on the sewer
After connecting the supply tubes connect the tube * 2 (waste) to a drain pipe to
the sewer.
Front ProfiDrum Eco range.
Front of the drum connection with waste disposal,
top tube.
Questo manuale è adatto per i seguenti modelli
4
Indice
