ProHD DT-X53F Manuale utente
1
Model: DT-X53F
5.5’’ Full HD Camera-top LCD Monitor
User Manual
Ver: B
Please read this User Manual
throughout before using.
2
Preface
1. All internal technologies of this product are protected, including device, software and trademark.
Reproduction in whole or in part without written permission is prohibited.
2. All brands and trademarks are protected and other relative trademarks in this user manual are the
property of their respective owners.
3. Due to constant effort of product development, SWIT Electronics reserves the right to make
changes and improvements to the product described in this manual without prior notice.
4. The warranty period of this product is 2 years, and does not cover the following:
(1) Physical damage to the surface of the products, including scratches, cracks or other damage to
the LCD screen or other externally exposed parts;
(2) The LCD dot defects are not over three;
(3) Any damage caused by using third-party power adaptors;
(4) Any damage or breakdown caused by use, maintenance or storage not according to the user
manual.
(5) The product is disassembled by anyone other than an authorized service center.
(6) Any damage or breakdown not caused by the product design, workmanship, or manufacturing
quality, etc.
3
Maintenance
Warning
1. In order to reduce the risk of fire and electrical shock, do not lay this product in rain or damp
places.
2. Please keep away from the strong magnetic field; it may cause the noise of the video and audio
signals.
The power
1. Please use the power adapter provided or recommended by the manufacturer in order to avoid
damage.
2. For a third party power adapter, please make sure the voltage range, supplied power, and
polarity of power lead are fit.
3. Please disconnect the power cable under the following situations:
(A). If you do not operate this monitor for a period of time;
(B). If the power cable or power adaptor is damaged;
(C). If the monitor housing is broken.
The monitor
1. Please don't touch the screen with your fingers, which would probably deface the screen.
2. Please don't press the screen; the LCD is extremely exquisite and flimsy.
3. Please don't lay this product on unstable place.
Cleaning
1. Please clean the screen with dry and downy cloth or special LCD cleanser.
2. Please do not press hard when cleaning the screen.
3. Please do not use water or other chemical cleanser to clean the screen. The chemical may
damage the LCD.
4
Contents
Preface .................................................................................................................................................................. 2
Maintenance ......................................................................................................................................................... 3
Contents ................................................................................................................................................................ 4
Packing list ............................................................................................................................................................ 4
Operation Instructions ......................................................................................................................................... 6
·OSD .............................................................................................................................................................. 7
·Zoom-in and mapping ................................................................................................................................ 8
Main menu........................................................................................................................................................... 10
Sub-Menu ............................................................................................................................................................ 11
Specification ........................................................................................................................................................ 18
Trouble-shooting................................................................................................................................................. 19
Packing list
Basic package includes:
1x Foldable sun hood
1x SSL-JVC battery plate
1x D-tap to lockable pole-tap DC cable
1x Pole-tap to lockable pole-tap DC cable
1x Cold shoe & Screw mounting arm trestle
1x 50cm BNC video cable
Professional package includes additional:
1x AC-DC lockable power adaptor
1x Lockable HDMI cable (60cm)
1x Carrying case
5
Dimension
The main body (mm)
Sun hood installation
⑴ Take out the sun hood from the flannel bag, see pic1;
⑵ Push out the sun hood as pic2, unfold as pic3;
⑶ Fold the two bottom parts inward as pic3, with the internal magnets attached and fixed as pic4;
⑷ Install the sun hood on the monitor, see as pic5.
1 2 3 4 5
Battery plate installation
Install the battery plate on the back panel of the monitor as shown above, fix with four screws,
then insert the power connector with lock to the rear housing power port, and twist the latch
portion clockwise to the end. Mounting the battery to the plate can power the monitor.
Screw 1
Screw 2
Screw 4
Screw 3
Power plug
6
Operation Instructions
⑴ F1 - F3: User definable function keys
User can set F1, F2, F3 keys to corresponding function for quick operation. For details please
refer to “Sub Menu - 4.Function key”.
When user press and hold the function keys for more than 3 seconds, it will pop-up a definable
function list menu, user can rotate and press to select functions. If no operation exceeds 3
seconds, the monitor will automatically save the selection and Exit.
When the menu system is on, press F3 to directly exit the menu at any time.
⑵ Menu Knob
Press the Menu knob to open the menu system on the left top of the screen;
Rotate the knob up and down to select menu items and press the knob to enter or confirm.
⑶ Micro USB port: Connect external storage device, for firmware upgrades.
⑷ PHONE: 3.5mmheadphone jack, output SDI/HDMI embedded audio.
⑸ SPEAKER: SDI/HDMI embedded audio output (will not work if headphone is connected)
⑹ DC IN: Pole DC power input socket (Outer: Negative, Inner: Positive)
⑺ POWER: Switch on/off the power
⑻ SDI-OUT: When current display signal is SDI, it will loop through output SDI signal;
When current display signal is HDMI, it will convert HDMI to SDI output.
* The HDMI to SDI conversion doesn’t support SD signal.
⑼ SDI-IN: 2K/3G/HD/SD SDI input (BNC)
⑽ HDMI-IN: HDMI 1.3 input (HDMI-A type)
⑾ Battery plate installation area
7
·OSD
⑴ Timecode (SDI)
Under SDI input, it can display Timecode. If no Timecode information is detected, it will be
displayed as “TC: UNLOCKED”.
User can set function keys F1 -F3 as “Timecode” to turn on or off this function
⑵ UMD
Display the source title. Set up under “UMD” submenu.
⑶ AFD (SDI)
User can set function keys F1 -F3 as “AFD” to turn on or off this function. If no relevant information
is detected, it will be displayed as “AFD: UNLOCKED”.
⑷ Audio meters
Monitor the audio information. User can set function Keys F1 -F3 as “Audio” to turn on or off this
function. The audio meter position, audio channels and blending, etc can be set under “Audio”
submenu.
⑸ Histogram
User can set function Keys F1 -F3 as “Histogram” to turn on or off this function.
⑹ Vector
User can set function Keys F1 -F3 or GPI pins as “Vector” to turn on or off this function.
The Vector position, Vector color and Vector blending, etc. can be set under “Vector” submenu.
⑺ Waveform
User can set function Keys F1 -F3 or GPI pins as “Waveform” to turn on or off this function.
The Waveform position, type, color and blending, etc can be set under “Waveform” submenu.
8
Zoom-in and mapping
Set “Zoom-in” to function keys, and enable zoom-in mode, the OSD displays as above.
⑴ Zoom-in steps operation
Scroll the Menu key up and down, to quick adjust zoom-in steps among: 1.2x, 1.5x, 1.8x, 2.0x,
2.4x, 2.6x, 2.8x and 3.0x. The zoom-in indication window is displayed on bottom right of the
screen.
⑵ Left and Right mapping
Press Menu key, the button is highlighted. Scroll the Menu key up and down to move the
video left and right.
⑶ Up and Down mapping
Press Menu key again, the button is highlighted. Scroll the Menu key up and down to move the
video up and down.
⑷ Peaking precision adjust
Press Menu key again, the peaking precision number is highlighted. S croll the Menu key up and
down to adjust the peaking focus assist precision from 0-9.
⑸ Mapping indication window
Under zoom-in mode, the mapping indication window is displayed on bottom right of the screen,
and indicates the zoom-in rate, up/down/left/right position.
9
Introduction of audio and video functions
16-ch embedded audio meters
The monitor can display max 16 channels audio meters for SDI embedded audio, and 2 channels
meters for HDMI embedded audio. The audio meter is green, and will turn yellow when audio
exceeds -20dB, and turn red when audio exceeds -9dB.
Audio alarm
If the embedded audio value is too low or no embedded audio, it will display “MUTE” or
“UNLOCKED” in the audio bar.
Timecode（ ）SDI
Under SDI input, it can display the SMPTE timecode (VITC1, VITC2 or LTC) on the top of the
screen. If no Timecode information is detected, it will be displayed as “UNLOCKED”.
Waveform (Y, Cb, Cr, R, G, B and single line)
Under SDI and HDMI input, Y, Cb, Cr, R, G, B and single line waveforms can be selected to
display
Vector
The displayed vector scope pattern is available under both SDI and HDMI, represents saturation
as distance from the center of the circle, and hue as the angle, in standard position, around it.
Histogram (R, G, B)
The histogram is a bar graph that shows the distribution of luminance values in the picture.
There’re R, G, B histograms that individually displayed simultaneously, available under both SDI
and HDMI.
Internal Color Bar
Under SDI and HDMI input, it has 100% internal color bar which helps to analyze the monitor color
and adjust the display parameter.
Peaking focus assist (red/blue switch)
The Peaking focus assist function is to mark the sharpest edges of the image with red or blue
color under SDI and HDMI input, for users to check if the subjects are focused.
Zebra stripes
Zebra Stripes are used to check if the image is over exposed or not by showing black and white
lines on the monitor. It is considered over exposed when luminance value exceeds 90%.
Freeze Frame
The freeze frame is to capture and display the current broadcast frame.
R/G/B/Mono
R/G/B/Mono is to display only the blue/red/green primary signal or the luminance signal only so as
to monitor the image noise.
False Color
The false color is used to aid in the setting of camera exposure. Under false color mode, there’s a
color chart on the bottom of screen for reference. The color from the dark to the bright will be
displayed as blue, cyan, green, yellow, orange and red in a consecutive way.
AFD (SDI)
It is the abbreviation of active format description. AFD is to display the SDI embedded AFD
information graphically on the screen.
H/V Delay (SDI)
Under SDI input, H/V Delay can be used to display line/field blanking signal, and to observe the
horizontal and vertical synchronous signal.
Flip and Rotate
The image can be set up/down flip, or left/right mirror display, like:
Normal Left to right Up to down 180° Rotate
10
Main menu
DT-X53F has OSD to adjust the parameters and settings, for example: Picture, color temp., function
keys, etc.
1. Press “MENU” button, the main menu will pop-up from the left top of the screen. The selected main
menu highlights in yellow.
2. Revolve “MENU” to select submenu, the selected submenu highlights in yellow, press “MENU” to
apply and enter into the selected submenu’s items.
3. Revolve “MENU” to select the item which needed to adjust, press “MENU”, the selected item and its
parameters will be highlighted in yellow.
4. Revolve “MENU” to change the selected item’s parameter, press “MENU” to apply and save the
settings.
5. Revolve “MENU” to select “Exit”, press “MENU” to quit submenu. Select “Exit & Status” under the
Main Menu and press to quit Main Menu.
Notice:
* The items in gray cannot be set up.
* If there is no operation under the set time, the menu will automatically save settings and quit.
* If the key inhabit function is turned on, except key inhibit function, all other items are in grey. Please
turn off the key inhibit function to adjust the items.
Indice
Altri manuali ProHD Monitor
ProHD
ProHD DT-X92F Manuale utente
ProHD
ProHD ProHD DT-X71F Manuale utente
ProHD
ProHD ProHD DT-X71C Manuale utente
ProHD
ProHD DT-X51Hx3 Manuale utente
ProHD
ProHD DT-X16H Manuale utente
ProHD
ProHD DT-N17H Manuale utente
ProHD
ProHD DT-X7HUx2 Manuale utente
ProHD
ProHD DR-N17F Manuale utente
ProHD
ProHD DT-X93H Manuale utente
ProHD
ProHD DT-N21H Manuale utente
