Project Source 16439-002 Manuale utente
1
Questions, problems, missing parts?
Departamento de Servicio al Cliente al 1-866-389-8827, de lunes a viernes de
8 a. m. a 6 p. m. y los viernes de 8 a. m. a 5 p. m., hora estándar del Este.
Antes de volver a la tienda, llame a nuestro
ADJUNTE SU RECIBO AQUÍ
Número de serie Fecha de compra
ITEM #0650171
4-HEAD LINEAR
MODEL #16439-002
Lowes.com
AB1532
TRACK KIT
Français p. 9Español p. 1 Français p. 9
Español p. 17
PACKAGE CONTENTS
2
Cover (Preassembled to
Mounting Bracket (A))
Supply Connector
(Preassembled to Mounting
Bracket (A))
Mounting Bracket
(Preassembled to Cover (C))
1
1
1
C
Support Screws
(Preassembled to Mounting
Bracket (A))
2D
B
AScrew (Preassembled to
Mounting Bracket (A)) 2
Track Head Assembly 4G
E
Track Section 1F
4bluBH
QUANTITY
DESCRIPTIONPART QUANTITY
DESCRIPTIONPART
C
B
A
E
D
F
G
H
Lowes.com
SAFETY INFORMATION
CAUTION
• For use with “hbt” series track only.
• Save these instructions and refer to them when additions to or changes to the track configuration
are made.
• ELECTRICAL CONNECTIONS (Required Supply Circuit: 120V, 60Hz)
• Connect the white wire(s) from the fixture to the white wire of the supply circuit. Connect the
black wire(s) from the fixture to the black wire of the supply circuit. Connect the green (or bare
copper) colored wire to the grounding conductor of the supply circuit. Use U.L./CSA Listed wire
connectors suitable for the size, type and number of conductors. No loose strands or loose
connections should be present. Secure wire connectors with U.L./CSA Listed electrical tape.
• To ensure the success of the installation, be sure to read these instructions and review the
diagrams thoroughly before beginning.
• All electrical connections must be in accordance with local codes, ordinances, and the National
Electric Code. If you are unfamiliar with methods of installing electrical wiring, secure the
services of a qualified licensed electrician.
• This system is intended to be supplied by a single 120-volt branch circuit. Before you begin,
check circuit load.
• This system is to be mounted to an electrical junction box at a minimum of 6 ft. above ground
level and 6 in. from any combustible material. The box must be directly supported by the building
structure. Do not pendant mount such as by a cable or stem.
• Before starting the installation, disconnect the power by turning off the circuit breaker or by
removing the appropriate fuse at the fuse box. Turning the power off using the light switch is not
sufficient to prevent electrical shock.
• GENERAL: This system can be expanded upon by purchasing additional "HBT" series
components.
WARNING
• To avoid risk of electric shock or fire, do not modify this lamp, if any modification is made it may
render the product unsafe.
3
HARDWARE CONTENTS
Junction
Box Screws
Qty. 2
Wire
Connector
Qty. 3
AA BB
Toggle
Bolt
CC DD
Qty. 2
Wood
Screws
Qty. 2
EE
Plastic
Anchors
Qty. 2
FF
Suction
Cup
Qty. 1
End Cap
Qty. 2
Lowes.com
GG
4
ASSEMBLY INSTRUCTIONS
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare parts with
package contents list and diagram above. If any part is missing or damaged, do not attempt to
assemble the product. .
Estimated Assembly Time: 45 ~ 60 minutes, add an additional 20 minutes if field cutting and
drilling is required.
Tools Required for Assembly (not included): Stepladder, Phillips screwdriver, Flathead screwdriver,
Wirecutters, Pliers, Safety Goggles, Drill, Handsaw
Helpful Tools (not included): Wire stripper, Electrical tape
1. If you want to field cut the track section (F), mark the
track section (F) at desired length and remove end caps.
Take into consideration the length of the connectors to be
used if any.
Secure the track section (F) and with a blunt instrument tap
on the copper strip on interior buss bars until they are
dislodged. Work on the track section (F) end that will be
cut off and disgarded. Do not remove the buss bars.
Reattach the end caps with the interior buss bars in place
and cut the track section (F) at mark. Make sure the cut is
straight with no burrs.
With one end cap (GG) in place pull the copper strips out
and cut 3/8 in. off of each strip. Push the copper strips back
in and replace other end cap (GG) or make connection to
other track connector.
F
F
F
F
1
3/8 in.
3/8 in.
IMPORTANT SAFETY INSTRUCTIONS – READ AND SAVE
Lowes.com
When installing or using this track system, basic safety precautions should always be followed,
including the following:
a) Read all instructions
b) Do not install this track in damp or wet locations.
c) Do not install any part of a track system less than 5 ft. above the floor.
d) Do not install any fixture assembly closer than 6 in. from any curtain, or similiar combustible material.
e) Disconnect electrical power before adding in or changing the configuration of the track .
f) Do not pendant mount this track such as by stems or wires.
g) Do not attempt to energize anything other than the lighting track fixtures on the track. To avoid
shock, do not attempt to connect power tools, extention cords. appliances, and the like.
GG
GG
5
ASSEMBLY INSTRUCTIONS
2. If you want to field drill the track section (F), mark location
of holes and center on track section (F). Drill a perpendicular
3/16-in. hole at marks and remove burrs. Be sure not to
damage insulators or conductors. Use mounting hardware
(not included) that does not come in contact with the
insulators or conductors to complete job.
Note: A single section of track that is 4 ft. or less in length is
to be provided with one mounting opening spaced a
maximum of 6 in. from each end of the track section (F).
Additional openings might also be provided. A single section
of track that is greater than 4 ft. in length is to be provided
with a mounting opening spaced a maximum of 12 in. from
each end of the track section (F), with additional openings
being placed a minimum of every 4 ft. along the length of the
track section (F).
5. For installing fixture on drywall ceiling, use toggle bolts
(CC). Drill a 5/8 in. hole at each mark on ceiling, insert bolts
through the track and thread toggles 1/2 in. onto bolts. Place
track section (F) against the ceiling and insert toggles into
holes until they spring open. Tighten bolts.
F
CC
Hardware Used
Toggle Bolt x2
CC
2
5
3. Make electrical connections using wire connectors (BB).
Refer to ELECTRICAL CONNECTIONS in the Safety
Information section on page 3. Install the mounting bracket
(A) to the junction box by using junction box screws (AA).
4. Determine location and attach track scetion (F) to
mounting bracket (A) and secure with support screws (D).
Place track section (F) and
supply
connector (B) at desired
location on ceiling, noting location of electrical supply. Mark
ceiling through holes in track section (F) and remove it from
the ceiling.
Hardware Used A
3
4
Junction
Box Screws x2
BB
Wire Connector x3
BB
AA
F
AA
D
F
B
A
Lowes.com
6
ASSEMBLY INSTRUCTIONS
8. Identify ground side of supply connector (B) and track
section (F). Insert supply connector (B) into track section (F)
and twist to secure. Make sure the ground side of supply
connector (B) aligns with ground side of track section (F).
Note: The ground side of connector (B) is the side with the
two metal tabs. The ground side of the track section (F) has
an indented groove on the face and two internal copper bars.
The supply connector (B) can only be assembled if the
ground sides are aligned.
9. Tighten support screws (D). Install cover (C) and secure
with screws (E).
B
C E
D
10. Identify ground side on track head assembly (G) and
track section (F). Insert track head assembly (G) connector
into track section (F) and twist to secure. Make sure the
ground side on track head assembly (G) connector aligns
with ground side of track section (F).
Note: The ground side of track head assembly (G) connector
is the side with the two metal tabs. The ground side of the
track section (F) has an indented groove on the face and two
internal copper bars. The track head assembly (G) can only
be assembled if the ground sides are aligned.
GROUND TAB
GROUND
GROOVE
IDENTATION
8
9
6
7
6. For installing fixture on studs in ceiling or wall, use wood
screws (DD).
DD
F
Wood Screws x2
DD
Hardware Used
7. For installing fixture on drywall in a wall application, use
plastic anchors (EE) and wood screws (DD).
DD
F
Plastic Anchors x2
EE
Wood Screws x2
DD
EE
Hardware Used
F
10
G
F
GROUND TAB
GROUND
SIDE GROOVE
IDENTATION
Lowes.com
7
ASSEMBLY INSTRUCTIONS
11. Attach the suction cup (FF) to the bulb (H), and
secure the bulb (H) to the socket on track head
assembly (G) by twisting and locking correctly. Detach
the suction cup (FF) from the bulb (H) by pulling the
small pin.
12. To remove track head from track, allow track head
to cool down, grasp track head connector and pull
down while twisting until track head disengages.
Hardware Used
Suction Cup x1
FF
11
12
G
G
H
FF
Lowes.com
8
CARE AND MAINTENANCE
• This unit is suitable for indoor use only.
• Clean this unit periodically. Clean only using water and mild soap; dry with a soft cloth.
Never use rough cloth, abrasives or chemical cleaners containing acids or harsh solvents.
LIMITED WARRANTY
Manufacturer warrants all of its lighting fixtures against defects in materials and workmanship for
one (1) year from the date of original purchase.
This warranty does not cover parts becoming defective due to misuse, accidental damage,
improper handling and/or installation and specifically excludes liability for indirect, incidental or
consequential damages. Product found to be defective may or may not be replaced with same or
like type product, contingent on the nature of the defect, and or replacement availability and or
compensated for at a pro rated value. Some states do not allow limitations on how long an implied
warranty lasts, and/or the exclusion or limitation of incidental or consequential damages, so the
above limitations or exclusions may not apply to you. This warranty gives you specific rights and
you may also have other rights, which vary from state to state. Proof of purchase is required to
exercise the warranty.
TROUBLESHOOTING
If you have any questions regarding the product, please call our customer service department at
1-866-389-8827, 8 a.m. - 6 p.m., EST, Monday - Thursday, 8 a.m. - 5 p.m., EST, Friday.
ProblemPossible Cause Corrective Action
Ground side of track
head connector and
track section are not
aligned
Align ground side of track head connector
(side of the connector with two metal tabs) and
track section (indented groove on face and two
internal copper bars)
Bad main supply wiring Consult a certified professional electrician
Defective switch Consult a certified professional electrician
Fuse blows or
circuit trips when
fixture is turned on
Wrong wiring or power
wire is grounding out
Consult a certified professional electrician
Light will not turn on
Printed in China
Lowes.com
Project Source is a registered trademark of LF, LLC. All rights reserved.
®
9
Des questions, des problèmes, des pièces manquantes? Avant de retourner l’article au
détaillant, appelez notre service à la clientèle au 1 866 389-8827, entre 8 h et 18 h (HNE),
du lundi au jeudi, ou entre 8 h et 17 h (HNE) le vendredi.
JOIGNEZ VOTRE REÇU ICI
Numéro de série Date d’achat
ARTICLES #0650171
NÉCESSAIRE DE RAIL
D’ÉCLAIRAGE LINÉAIRE
À QUATRE LUMIÈRES
MODÈLES #16439-002
Lowes.com ®
CONTENU DE L’EMBALLAGE
10
Couvercle (préassemblé au
support de fixation [A])
Connecteur d’alimentation
(préassemblé au support de
fixation [A])
Support de fixation
(préassemblé au couvercle [C])
1
1
1
C
Vis de soutien (préassemblée
au support de fixation [A]) 2D
B
AVis (préassemblée au
support de fixation [A]) 2
Ensemble de projecteur 4G
E
1liaRF
4eluopmAH
Quantité
DescriptionPièce Quantité
DescriptionPièce
C
B
A
E
D
F
G
H
Lowes.com ®
Indice
Lingue:
Altri manuali Project Source Attrezzatura di illuminazione
Project Source
Project Source EC1596WH Manuale utente
Project Source
Project Source UT1056 Manuale utente
Project Source
Project Source 0650141 Manuale utente
Project Source
Project Source 20261-000 Manuale utente
Project Source
Project Source FV05-094-3 Manuale utente
Project Source
Project Source 15678-001 Manuale utente
