Prokit’s TE-3210B Manuale utente
TE-3210B
DC To AC Power Inverter
1000W 50Hz Modify Sine Wave
TE-3210B: DC12V to AC220V~240V
AC OUTPUT
AC
OUTLET
ON
OFF
User’s Manual
1st Edition,2016
©2016 Copy Right by Prokit’s Industries Co., Ltd
1
Instruction Manual
Please read user manual before use.
USEFUL APPLICATIONS
RUN NOTEBOOK COMPUTERS, RADIOS, TVS, VCRS, LAMPS, FANS, FAX,
DRILL . . . . . . ETC.
SPECIFICATION
Input voltage range : DC 10~15V (12V)
Input full load current : 100A(12V)
Standby input current : <0.6A (12V)
Output voltage (AC) : 220V~240V
Output waveform : modify sinewave
Output frequency : 50Hz or 60Hz
Continue output power : 1000W
Peak output power : 2400W
Efficiency : 85~90%
Battery low pre-alarm : 10.5 ± 0.5V (12V)
Battery low shutdown : 10 ± 0.5V (12V)
Thermal protect : 60 ± 5℃(microcontroller)
Auto-operation fan(Temperature or Load)
Overload protection : YES (microcontroller)
Output short protection : YES (microcontroller)
Battery ex. 12V protection : YES (microcontroller )
Battery polarity protection : YES (by fuse )
Fuse : 20A*6PCS (12V)
Transger time : 16m sec.
Charger current : MAX. 10A (12V)
Dimension ( L*W*H) mm : 430 * 135 * 79
Weight : 3.1 kg
TROUBLESHOOTING
If the inverter does not appear to be functioning properly, there are several
reasons why the inverter may not be responding.
1) Poor contact
*Cleaning contact parts thoroughly.
2) Receptacle has no power
*check fuse, replace damaged fuse.
*check receptacle wiring. repair if necessary
3) Fuse is blown
2
*The fuse is located inside the DC plug. Please replace fuse with a new
equivalent value fuse.
4) Overload caused AC output reduce
*Reduce the wattage of loading to lower than 1000 watts.
5) Thermal caused AC output reduce
*Under heavy loads for extended periods of time. The AC inverter will
reduce output to prevent damage to excess heat. If this happened,
please proceed as below:
(A) Switch off the power of this inverter.
(B) Decreases the load of this machine i. e. disconnect some of the
appliances or wait until this inverter become cool.
(C)Switch on the power of this inverter.
6) Low-battery shutdown
*Recharge your battery and resume operation.
FAN
TERMINAL
( + )
TERMINAL
( - )
WARNING:DC INPUT
DO NOT REVERSE INPUT
POWER SWITCH
AC OUTPUT SOCKET
AC OUTPUT
AC
OUTLET
ON
OFF
MAIN POWER
IN FUSE
CAUTION : DO NOT REVERSE INPUT. USE RED BATTERY CORD TO
CONNECT (+) OF A DC BATTERY TO (+) TERMINAL. AND THEN, USE
BLACK BATTERY CORD TO CONNECT (-) BATTERY TO (-)
TERMINAL.
BATTERY
RED
BLACK
3
WARNING SIGNAL
Condition Warning signal cycle Shutdown signal cycle
Low battery alarm: BI BI BI (pause) BEE BEE BEE (pause)
Over heating alarm: BI BI (pause) BEE BEE (pause)
Over load alarm: BI BI BI BI BI BI Continuous tone
Note: BI is a short beep, and BEE is a longer beep.
※ USE INVERTER
STEP1:SET THE POWER SWITCH AT THE OFF
ON
OFF
AC
OUTLET
STEP2:
WHEN CONNECTED TO ANY APPLIANCE, BE SURE TO TURN ON
INVERTER FIRST. AND THEN, TURN ON THE POWER SWITCH OF THE
APPLIANCE.
TURN ON
FIRSTLY
TURN ON
SECONDLY
DO NOT USE THE INVERTER EXCEED ITS MAXIMUM OUTPUT
POWER, WHEN CONNECTED TO ANY APPLIANCE. MAKE SURE
THE TOTAL STARTING POWER CAPACITY DOES NOT EXCEED THE
MAXIMUM OUTPUT POWER OF THE INVERTER.
BATTERY
4
※ AS UPS
IF YOU WANT TO USE THIS UNIT AS U.P.S. FUNCTION , TURN ON THE
SWITCH OF THE INVERTER AT FIXED POSITON FIRSTLY.
WHEN THE BLACK OUT OCCURS IN THE MEANTIME, THE INVERTER
WILL DIVERT AUTOMATICALLY FROM HOME ELECTRICITY INTO THE
BATTERY TO SUPPLY THE POWER FOR APPARATUS USE
CONTINUALLY.
ON
OFF
BATTERY
HOME MAIN SOCKET
※
5
※ CHARGER
CONNECT AC INPUT POWER CORD TO HOME MAIN SOCKET
THEN USE RED BATTERY CORD TO CONNECT (+) OF DC
BATTERY TO (+) SINDING POST.AND USE BLACK BATTERY
CORD TO CONNECT (-) BATTERY TO (-) SINDING POST.
BATTERY
HOME MAIN SOCKE
T
AC
OUTLET
POWER SWITCH ON POWERSWITCH
OFF
OFF
ON SLOWLY
CHARGING QUICK
CHARGING
6
BATTERY LED DARK/LIGHT INDICATIVE CHART.
12V 13.5V
A
14.5V13V12.5V
BATTERY
LED
LIGHT
BATTERY
LED
BLINKS
BATTERY
LED
LIGHT
BATTERY
LED
LIGHT
14V
:CHARGER CURRENT
(24V)
0A
5A
4A
3A
2A
1A
7A
6A
8A
10A
9A
0A
2.5A
2A
1.5A
1A
0.5A
3.5A
3A
4A
5A
4.5A
(24V) (28V)(27V)(26V)(25V) (29V)
V 0.4(24V)
V 0.2(12V)
INDICATING SIGN
NORMAL LIGHTED LED : POWER SWITCH “ ON ” , INVERTER
STANDBY
NORMAL UNLIGHTED LED : POWER SWITCH “ OFF ”
CHARGER LIGHTED LED : BATTERY CHARGING
CHARGER LED BLINKS : FULL BATTERY
AC IN LIGHTED LED : MAIN POWER IN
ON
NORMAL
CHARGER
AC
OUTLET
7
IF THE TOTAL WATTS OF ELECTRICAL APPLIANCES EXCEEDS
THE OUTPUT CAPACITY OF INVERTER. OR AFTER OPERATING
FOR A PERIOD OF TIME. IF THE TEMPERATURE OF THE
INVERTER REACHES 60℃, THE INVERTER SHALL BE REDUCED
AC OUTPUT BY THE PROTECTION CIRCUIT.
0
60 C
.
CAUTION
* ALWAYS PLACE THE INVERTER IN
AN ENVIRONMENT WHICH IS :
( A ) WELL VENTILATED
( B ) NOT EXPOSED TO DIRECT
SUNLIGHT OR HEAT SOURCE
( C ) OUT OF REACH FROM CHILDREN
( D ) AWAY FROM WATER/MOISTURE,
OIL OR GREASE
( E ) AWAY FROM ANY FLAMMABLE
SUBSTANCE
※WARNING※FLUORESCENT LAMP
DO NOT USE THIS DEVICE WITH FLUORESCENT LAMPS.
BALLASTS
Glow switch
Lamp
AC IN
Power Factor
Capacitor
ab
.
Indice
