Promaker PRO-TP550 Manuale utente
Lavadora de Alta Presión
Manual del Usuario
Modelo No.: PRO-H1400
High Pressure Washer
User’s Manual
Model No.: PRO-H1400
HAMMER DRILL
User’s manual
Model No.: PRO-TP550
English: 2 I Español: 11
2
THANK YOU FOR BUYING OUR PRODUCT.
To ensure your safety and satisfaction, carefully read through this OWNER’S MANUAL
before using the product.
General power tool safety warnings
WARNING Read all safety warnings, instructions, illustrations and specications provided with
this power tool. Failure to follow all instructions listed below may result in electric shock, re and/or
serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-
operated (cordless) power tool.
1) Work area safety
a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the presence of ammable liquids, gases or
dust. Power tools create sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with
earthed (grounded) power tools. Unelectric shock.
b) Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There
is an increased risk of electric shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric
shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away
from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable
for outdoor use reduces the risk of electric shock.
f) If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected
supply. Use of an RCD reduces the risk of electric shock.
a) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a
power tool while you are tired or under the inuence of drugs, alcohol or medication. A moment of inattention
while operating power tools may result in serious personal injury.
b) Use personal protective equipment. Always wear eye protection. Protective equipment such as a dust mask,
nonskid safety shoes, hard hat or hearing protection used for appropriate conditions will reduce personal
injuries.
c) Prevent unintentional starting. Ensure the switch is in the off-position before conecting to power source and/
or battery pack, picking up or carrying the tool. Carrying power tools with your nger on the switch or energising
power tools that have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool
in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair and clothing away from moving parts.
Loose clothes, jewellery or long hair can be caught in moving parts.
g) If devices are provided for the connection of dust extraction and collection facilities, ensure these are
3) Personal safety
3
connected and properly used. Use of dust collection can reduce dustrelated hazards.
h) Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool
safety principles. A careless action can cause severe injury within a fraction of a second.
a) Do not force the power tool. Use the correct power tool for your application. The correct power tool
will do the job better and safer at the rate for which it was designed.
b) Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/or remove the battery pack, if detachable, from
the power tool before making any adjustments, changing accessories, or storing power tools. Such
preventive safety measures reduce the risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of children and do not allow persons unfamiliar with the
power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of
untrained users.
e) Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage
power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused
by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into
account the working conditions and the work to be performed. Use of the power tool operations different
from those intended could result in a hazardous situation.
h) Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and
grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.
a) Have your power tool serviced by a qualied repair person using only identical replacement parts.
This will ensure that the safety of the power tool is maintained.
SAFETY WARNINGS
1. Wear ear protectors when hammer drilling. Exposure to noise can cause hearing loss.
2. Use the auxiliary handle(s). Loss of control can cause personal injury.
3. Brace the tool properly before use. This tool produces a high output torque and without properly bracing
the tool during operation, loss of control may occur resulting in personal injury.
4. Hold the power tool by insulated gripping surfaces, when performing an operation where the cutting
accessory may contact hidden wiring or its own cord. Cutting accessory contacting a “live” wire may make
exposed metal parts of the power tool “live” and could give the operator an electric shock.
5. Never operate at higher speed than the maximum speed rating of the drill bit. At higher speeds, the bit
is likely to bend if allowed to rotate freely without contacting the workpiece, resulting in personal injury.
6. Always start drilling at low speed and with the bit tip in contact with the workpiese. At higher speeds,
the bit is likely to bend if allowed to rotate freely without contacting the workpiece, resulting in personal injury.
7. Apply pressure only in direct line with the bit and do not apply excessive pressure. Bits can bend
causing breakage or loss of control, resulting in personal injury.
8. Make sure drill bit is securely mounted. An incorrectly mounted bit is extremely dangerous since it can y
off or break during drilling.
9. Do not wear cloth gloves or a necktie since they could become caught in a rotating bit.
10. Never touch the chuck or metal body parts when drilling walls, oors or other surfaces covering
electrical wiring. Hold the drill only by the plastic handle to prevent electric shock.
11. While operating the workpiece must be held with the vise or the clamp etc. securely, for preventing to move
it by the drill rotation.
4) Power tool use and care
5) Service
4
INSTRUCTIONS FOR SAFE HANDLING
1. Make sure that the tool is only connected to the voltage marked on the name plate.
2. Never use the tool if its cover or any bolts are missing. If the cover or bolts have been removed, replace
them prior to use. Maintain all parts in good working order.
3. Always secure tools when working in elevated positions.
4. Never touch the blade, drill bit, grinding wheel or other moving parts during use.
5. Never start a tool when its rotating component is in contact with the workpiece.
6. Never lay a tool down before its moving parts have come to a complete stop.
7. ACCESSORIES: The use of accessories or attachments other than those recommended in these
instructions might present a hazard.
8. REPLACEMENT PARTS: When servicing use only identical replacement parts.
DESCRIPTION
1. Drill chuck
2. Switch
3. Lock button
4. Reversing lever
5. Hammer shifting knob
6. Adjustment stopper
7. Aux. handle
8. Chuck key
9. Drill bit
10. Speed control dial
SPECIFICATIONS
Voltage: 120 V ~ 60 Hz
Input power: 550 W
No lsad speed: 0- 3000pm
Chuck size: 13 mm
Diling capacity:
Steel: 13 mm
Concrete: 13 mm
Wood: 25 mm
STANDARD ACCESSORIES
Aux. handle, Adjustment stopper, Chuck key
APPLICATIONS
(Use only for the purposes listed below.)
1. Drilling wood, metal and resin boards.
2. Drilling concrete (hammer drill only).
MOUNTING OF BIT (Fig. 1)
When mounting the drill bit (9), insert the bit into chuck (1) as far as it will go and tighten securely using the
chuck key (8) provided. There are three holes into which the chuck key should be inserted. Tighten each one
equally in turn.
The bit can be removed by following the above method in reverse.
5
SWITCH (Fig. 2)
This tool starts and stops by depressing and releasing the switch(2).
The speed can be adjusted from 0 through 3000 RPM by regulating the trigger-squeezing force.
For continuous operation, press the lock button(3) while switch is depressed. Depress again to release the lock.
The speed control dial(10) allows setting a limit on the desired speed.
CHANGING DIRECTION (Fig. 2)
To reverse the direction of rotation, stop the drill by releasing the trigger and push the reversing lever (4) to the
right or left.
When the reversing switch is in the position marked “F”, the direction of rotation will be clockwise when viewed
from the handle end of the drill. When the reversing switch is in the position marked “R” , the direction of
rotation will be counter-clockwise.
OPERATION OF PERCUSSION GEAR (Fig. 3)
An hammer shifting knob (5) has been provided on top of the gear case.
DRILLING Shift the hammer knob to the symbol indicating
“ ” for rotation without hammer action.
IMPACT MODE Shift the hammer knob to the symbol indicating
“ ” for hammer drilling.
OPERATING (Fig. 4)
NEVER COVER AIR VENTS SINCE THEY MUST ALWAYS BE OPEN FOR PROPER MOTOR
COOLING.
DRILLING IN WOOD
To prevent ugly splits around the drillhole on the reverse side of the workpiece, place a scrap
piece of lumber beneath the material to be drilled.
DRILLING IN METAL
Metals such as steel brass, aluminum sheets, stainless steel, and pipe may also be drilled. Mark
the point to be drilled with a nail or a punch.
DRILLING IN CONCRETE
Rock and masonry are generally drilled in the hammer mode.
When drilling delicate materials such as wall tiles, it is essential to start with ordinary drilling and once the tile is
pierced, to continue with hammer drilling.
In deep boreholes the drill bit should be pulled out occasionally in order to remove the dust and chips from the
hole.
6
AUX. HANDLE AND ADJUSTMENT STOPPER
Install the aux. handle (7) on the head of the housing and insert the adjustment stopper (6) in the hole
provided.
The aux. handle can swivel 360° for the most comfortable position and easiest operation.
The stopper helps keep an accurate depth when drilling holes.
MAINTENANCE
After use, check the tool to make sure that it is in top condition. It is recommended that you take this tool to an
Authorised Service Centre for a thorough cleaning and lubrication at least once a year.
DO NOT MAKE ANY ADJUSTMENTS WHILE THE MOTOR IS IN MOTION.
ALWAYS DISCONNECT THE POWER CORD FROM THE RECEPTACLE BEFORE CHANGING
REMOVABLE OR EXPENDABLE PARTS (BLADE, BIT, SANDING PAPER ETC.), LUBRICATING OR
WORKING ON THE UNIT.
WARNING!
To ensure safety and reliability, all repairs should be performed by an AUTHORISED SERVICE CENTRE or
other QUALIFIED SERVICE ORGANISATION.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
WARNING To reduce the risk of injury, user must read instruction manual
Class II construction tool in which protection against electric shock does not rely on basic
insulation only, but in which additional safety precaution, such as double insulation or reinforced insulation,
are provided.
NOTES
NOTES
NOTES
www.promakertools.com
Indice
Lingue:
Altri manuali Promaker Trapano
