ProMaxX Clixx'Pixx DrillPunch Pro2 Manuale utente

1. Unpack machine system and check

Find these items

StudioAlbums

Check that your Drill Punch pack contains all neccessary parts shown above.

Warning: This machine contains sharp cutting dies. Please handle with caution and keep your

ngers away from the cutting area.

Operating instructions EN 06.2014

Clixx’Pixx DrillPunch Pro2 4-12” 56-1012

Page 1

Transport locking belt

Please remove

Machine

Accessories

2 Limiter Blocks

Cleaning Brush

Alignment Block 12”

Alignment Blocks: 4” 5” 6”

Hexagon Key

Tension

Rubber Band

-Spare/Extra-

6 Counter

Pressure

Disks

2 Alignment Blocks A4

Portrait and Landscape

OPTIONAL !

Art.-Nr. 56-1903

Punch

Alignment

Bar

Tension

Rubber

Band

45°

2. Make system ready

Install PunchAlignmentBar and place LimiterBlocks

StudioAlbums

Page 2 Clixx’Pixx DrillPunch Pro2 4-12” 56-1012

Check correct installation of Punch

Alingment Bar and TensionRubber-

Band

New punches, like this one, are equipped

with a PunchAlignmentBar and a

TensionRubberBand. This assures

punching in a perfect line.

Make sure, both parts are in place as

shown.

Check correct position of Counter

Pressure Disks

Use hexagon key wrench to check that

CounterPressureDisks are all the way

back in their correct position.

Place Limiter Blocks

Install LimiterBlocks as shown.

All pictures up to 8” are drill-punched

using the 2 Limiter Blocks in their

appropriate position.

Remove Limiter Blocks only for pictures

12” high.

Always drill a complete book of pictures. Do not drill single pictures.

Please align the stack of pictures carefully and x it with your other

hand while punching.

Put a misprint on top of the stack to avoid unwanted marks on the rst

print by the punch hold down.

Clean the working surface and the counter pressure disks with the

brush after every operation (see picture at right).

Rotate the counter pressure disks a little, if the punchings on the last

sheet do not look OK. (See page 5).

The punch clippings are pushed up inside the hollow drills and fall into

the wastbasket on rear of machine. Empty regularly. (See page 5)

The punch is designed for SilverHalide paper and for DryInk paper with

polyethylen layer only!! If you want to use other type of papers,

please contact us for advice.

After intensive use, cutting might get arduous, because cutting edge of

punch becomes dull.

See page 6 for replacement instructions.

IMPORTANT

BE GENERALLY

CAREFUL:

WATCH SHARP EDGES

OF CUTTING TOOLS!

Drill binding holes 4”(101,6mm) print height:

Drill binding holes 5“ (127mm) print height:

4” Images are punched only one time.

►Arrange all prints of a book in a clean square pile.

►Use the 4” alignment block as shown and punch the

pile once.

5” Images are punched two times.

►Arrange all prints of a book in a clean square pile.

►Use the 5” alignment block as shown and punch the

pile once.

►Rotate the 5” alignment block by 90° and punch the

pile of prints the second time.

StudioAlbums

Page 3 Clixx’Pixx DrillPunch Pro2 4-12” 56-1012

3. Drill binding holes

See dierent procedures for dierent book heights

Drill binding holes 6“ (152,4mm) print height:

6” Images are punched two times.

►Arrange all prints of a book in a clean square pile.

►Use the 6” alignment block as shown and punch

the pile once.

►Rotate the 6” alignment block by 90° and punch

the pile of prints the second time.

►Align the Pile now on the right Limiter Block and

punch the Pile the second time.

12“ Prints are drillpunched 3 times,

with a total of 6 holes

►Arrange all prints of a book in a clean square pile.

►Push stack in the left upper corner and make sure all

sheets stay square in the stack.

►Push handle slowly and punch the pile once.

►Remove Limiter Blocks for Sizes 12” and A4

StudioAlbums

Page 4 Clixx’Pixx DrillPunch Pro2 4-12” 56-1012

Drill binding holes 8”(203mm) print height:

Drill binding holes 12“ (304mm) print height:

8” Images are punched two times.

►Arrange all prints of a book in a clean square pile.

►Use the left Limiter Block as shown and punch the

pile once .

►Now insert 12” alignment block as shown as a spacer

and repeat steps above.

►Now turn 12” alignment block as shown and repeat

steps above.

Drill binding holes A4Portrait and Landscape:

A4 Portrait has 4 binding holes, A4 Landscape has 3 binding holes.

Insert A4 Portrait alignment block as shown as

a spacer and arrange all prints of the book in a

clean square pile.

Push stack in the left upper corner and make sure

all sheets stay square in the stack.

Push handle slowly and punch the pile once.

Insert A4 Landscape alignment block as shown

as a spacer and arrange all prints of the book in a

clean square pile.

Push stack in the left upper corner and make sure

all sheets stay square in the stack.

Push handle slowly and punch the pile once.

Turn the alignment block as shown and repeat

punching.

Turn the alignment block as shown and re-

peat punching.

StudioAlbums

Page 5 Clixx’Pixx DrillPunch Pro2 4-12” 56-1012

4. Periodical machine care

Please always observe

Counter pressure disk

If the last pictures in a stack are not

cut cleanly, the counter pressure disk

must be rotated. Use hexagon key

wrench to pull it towards you, rotate

it by around 30 degrees to an unused

position and push it in backwards

again rmly.

Emptying the tray

The cut-outs are collected in the back

tray. About every 500 punchings you

have to empty the tray. Tap on the side

of the machine, so that all remains falls

into the tray. Then pull out towards

you and empty. Put back in position.

PortraitLandscape

Replace the counter pressure disk, if

there is no space for further punch-

ings left (like on picture above).

Hint: To remove the counter pressure

disk, push it towards you using the

hexagon key wrench.

1 2

StudioAlbums

Page 6 Clixx’Pixx DrillPunch Pro2 4-12” 56-1012

5. Exchange punching dies

7 8 9

5 6

Pull PunchAlignmentBar down and

towards you, so it gets out of your

way, as shown on picture 2.

This is how you remove PunchHolder

and punch from the machine.

The head of the punch must glide into

the rail as indicated.

Push in PunchHolder hard

and tighten screw rmly. Then

rearrange PunchAlignmentBar and

TensionRubberBand. Make sure is it

arranged as on picture on page 2 top

picture.

Important: Both punches are

calibrated in the machine. The right

position Punch holder is marked

with a red dot. Do not switch to the

left position!

Tilt PunchHolder again like shown and

carefully move assembly into machine.

Now replace the old punch with a new

one.

Loosen PunchHolderScrew as

indicated..... and tilt the PunchHolder a

little towards you.

This is legal information to potential licensees and business partners and not intended to be an advertising message:

PROMAXX® reserves all rights to the design, function and materials of these photo systems to the extent international patent laws allow. German utility models have been applied in

DE covering the PhotoBook covers, the Clixx‘Pixx Ring System and other proprietary features to allow for worldwide patent protection of these proprietary technologies. PROMAXX®

and Clixx´Pixx® are registered trademarks of PROMAXX® Innovative PC Print Media GmbH, Dietersheim / Munich, Germany. Potential business partner‘s contacts welcome.

All statements, technical Information and recommendations about PROMAXX® products are based upon tests believed to be reliable but do not constitute a guarantee or warranty. In

no event shall PROMAXX® be responsible for claims beyond the replacement value of the defective product or in any way liable or responsible for consequential or incidental dama-