PROPOINT 9081548 Manuale utente
V1.0 9081548
Please read and understand all instructions before use. Retain this manual for future reference.
SHOP PRESS
PNEUMATIC/HYDRAULIC
This page is intentionally left blank.
SPECIFICATIONS
Press Capacity 40,000 lb
Press Type Pneumatic/hydraulic
Ram Travel 6 in.
Working Range 3-5/16 to 18-1/8 in.
Bed Width 19-11/16 in.
Overall Height 39-13/16 in.
Pressure Rating 110 to 120 PSI
Material Steel Construction
INTRODUCTION
The workshop press is designed for light industrial use or for home
use. Perform straightening, stamping and bending with this powerful
hydraulic press. Features an H-frame design that makes it perfect for
removing or installing bearings, bushings, gears, ball joints, pulleys,
universal joints and more.
The press features a pneumatic foot control .
SAFETY
WARNING! Read and understand all instructions before
using this tool. The operator must follow basic precautions
to reduce the risk of personal injury and/or damage to the
equipment.
HAZARD DEFINITIONS
Please familiarize yourself with the hazard notices found in this manual.
A notice is an alert that there is a possibility of property damage, injury
or death if certain instructions are not followed.
DANGER! This notice indicates an immediate and specific hazard that will
result in severe personal injury or death if the proper precautions
are not taken.
WARNING! This notice indicates a specific hazard or unsafe practice that could
result in a serious injury if the proper precautions are not taken.
V1.0 PNEUMATIC/HYDRAULIC SHOP PRESS 9081548
Page 3 Assistance available at www.princessauto.com or 1-800-665-8685
CAUTION! This notice indicates a potentially hazardous situation that may
result in minor or moderate injury if proper practices are not taken.
NOTICE! This notice indicates that a specific hazard or unsafe practice will
result in equipment or property damage, but not personal injury.
WORK AREA
1. Operate in a safe work environment. Keep your work area clean,
well-lit and free of distractions. Place lights so you are not working
in a shadow.
2. Keep anyone not wearing the appropriate safety equipment away
from the work area.
3. Store unused tools properly in a dry, safe and secure location to
prevent rust, damage or misuse.
PERSONAL SAFETY
WARNING! Wear personal protective equipment approved
by the Canadian Standards Association (CSA) or American
National Standards Institute (ANSI).
PERSONAL PROTECTIVE EQUIPMENT
1. Always wear impact safety goggles that provide front and side
protection for the eyes. Eye protection equipment should comply
with CSA Z94.3-07 or ANSI Z87.1 standards based on the type of
work performed.
2. Wear the appropriate type of full-face shield in addition to safety
googles, as the work can create chips, abrasive or particulate
matter.
3. Wear protective clothing and gloves designed for the work
environment, materials and tools.
4. Wear steel toe footwear or steel toe caps to prevent a foot injury
from falling objects.
5. The tool may contain high pressure. Use safety glasses and gloves
for protection during operation. Keep hands clear of the exposed
rubber portions of the hose.
6. The air source used with this tool may cause hearing damage.
Wear ear protection gear to eliminate or reduce the noise.
9081548 PNEUMATIC/HYDRAULIC SHOP PRESS V1.0
Assistance available at www.princessauto.com or 1-800-665-8685 Page 4
PERSONAL PRECAUTIONS
Control the tool, personal movement and the work environment to avoid
personal injury or damage to tool.
1. Do not operate any tool when tired or under the influence of drugs,
alcohol or medications.
2. Avoid wearing clothes or jewelry that can become entangled with
the moving parts of a tool. Keep long hair covered or bound.
3. Avoid unintentional starts. Be sure that the regulator/throttle switch
is in the neutral or OFF position when not in use and before
connecting it to any air source.
4. Never point the air stream or tool at any point of your body, other
people or animals. Debris and dust ejected at high speed can
cause an injury.
5. Serious injury or death may occur from inhaling compressed air.
The air stream may contain carbon monoxide, toxic vapors or solid
particles. Never inhale compressed air directly from the pump or
air tool.
SPECIFIC SAFETY
WARNING! DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence to the
tool safety rules. If you use this tool unsafely or incorrectly,
you can suffer serious personal injury.
1. Use the correct tool for the job. This tool was designed for a
specific function. Do not modify or alter this tool or use it for an
unintended purpose.
2. The maximum load is 20 tons. Do not exceed this rated capacity.
Never apply excessive force to a workpiece and always use the
pressure gauge to accurately determine the applied load.
3. Inspect the press before each use. Do not use if any component
is bent, broken, cracked, leaking or showing other damage. Do not
use the press after a shock load until a qualified technician has
examined the press.
4. Check to ensure that all bolts and nuts are tight.
V1.0 PNEUMATIC/HYDRAULIC SHOP PRESS 9081548
Page 5 Assistance available at www.princessauto.com or 1-800-665-8685
5. Only use this shop press on a surface that is stable, level and not
slippery. The surface must be capable of sustaining the weight of
the shop press and the load.
6. Ensure that the workpiece is center-loaded and secure. An
unbalanced load may slip off the heel blocks or bed frame.
7. Keep hands and feet away from the bed frame area at all times.
8. Do not use the shop press to compress a spring or any other item
that could disengage and cause a potential hazard. Never stand
directly in front of a loaded press and never leave a loaded press
unattended.
9. Do not allow an untrained person to operate the press.
10. Do not use brake fluid or other improper fluid in place of hydraulic
oil. Avoid mixing different types of oil when adding hydraulic oil.
Only good quality hydraulic jack oil can be used.
11. Do not expose the press to rain, snow or inclement weather.
12. Bolt the press to the floor if it is to be used on bulky or
unstable items.
POWER TOOL PRECAUTIONS
1. Do not use any power tool with a malfunctioning power switch
or control. A power tool that fails to respond to the controls is
dangerous and can cause an injury. A qualified technician must
repair and verify the power tool is operating correctly, before it can
be used.
2. Shut the power off and disconnect the press from the power
supply (if possible) before making any adjustments, changing
accessories, cleaning, servicing or when storing. Such preventive
safety measures reduce the risk of starting the tool accidentally.
3. Check if the press's moving parts are misaligned or binding before
each use. Correct the issue before using the press to avoid an
injury or damage to the tool.
4. Avoid unintentional starts. Be sure that the regulator/throttle switch
is in the neutral or OFF position when not in use and before
connecting it to any air source.
9081548 PNEUMATIC/HYDRAULIC SHOP PRESS V1.0
Assistance available at www.princessauto.com or 1-800-665-8685 Page 6
HYDRAULIC PRECAUTIONS
DANGER! Seek immediate medical attention if hydraulic
fluid under pressure penetrates your skin. See Injection
Injury precautions for instructions before using a
pressurized hydraulic system.
1. Do not touch or handle, hydraulic hoses or components while
under pressure. Hydraulic fluid escaping under pressure has
sufficient force to penetrate your clothing and skin. A pinpoint hole
may inject hydraulic fluid into your body. Seek immediate medical
attention if this occurs (see Injection Injury).
2. Never exceed the hydraulic system’s load capacity (see
Specifications).
3. Do not adjust the hydraulic system’s relief setting. The settings are
preset by the factory.
4. Hydraulic oil under pressure is hot and can cause a burn injury
if touched, sprayed or spilled. Allow the hydraulic system to cool
before conducting maintenance.
5. Hydraulic components require regular inspection. Release all
pressure from the system before you inspect it. Replace damaged
hydraulic parts with identical manufacturer's components.
6. Do not attempt makeshift repairs to a hydraulic system. Such
repairs can fail suddenly and create a hazardous condition.
7. A damaged or disconnected hydraulic hose under pressure may
whip around and inflict personal injury or damage the work area.
Secure the hose to a fixed or permanent structure with clamps or
cable ties.
8. Hydraulic fluid has a combustible flash point of 200°F (93°F). Do
not expose the fluid to an ignition source.
9. Change your clothing immediately if sprayed with hydraulic fluid.
Store clothing or rags contaminated with hydraulic fluid in an
approved metal safety can with a spring-closing lid and venting
designed to contain a fire.
10. Only use hydraulic fluid in the pump. Do not substitute or mix
brake fluid, or any other fluid, with the hydraulic fluid. This can
V1.0 PNEUMATIC/HYDRAULIC SHOP PRESS 9081548
Page 7 Assistance available at www.princessauto.com or 1-800-665-8685
result in a pump failure and injure the user or bystander. It may
also damage the pump.
INJECTION INJURY
DANGER! Seek immediate, professional medical treatment
if fluid penetrates your skin. It may feel like a pricking or
sting. Do not wait for the appearance of symptoms. A toxic
reaction can occur from the exposure. Delay in treatment
can lead to amputation or death.
Inform the medical staff that you have a fluid penetration injury as soon
as you arrive at the medical facility. The severity of the symptoms will
depend on the type of fluid injected. Bring the Safety Data Sheet for the
fluid with you to the medical facility if possible.
INJECTION PRECAUTIONS
Fluid can penetrate the skin at 100 PSI pressure. Fluid escaping under
pressure from the tool has sufficient force to penetrate your clothing
and skin. Follow the precautions below to avoid an injection injury.
1. Always check for leaks wearing a face shield, safety goggles,
rubberized gloves and protective clothes.
2. Release all pressure from the system before you inspect it.
3. Do not use your hands to detect a leak. Use a large piece of wood,
cardboard or paper and watch for discolouration.
4. Replace damaged parts with identical manufacturer's components
to ensure it is rated to handle the pressure.
AIR TOOL PRECAUTIONS
1. Use only clean and dry compressed air as a power source.
Contaminated or moist air will gradually damage the tool.
2. Install an in-line shutoff valve or regulator to allow immediate
control over the air supply in an emergency, even if a hose is
ruptured.
3. Discontinue tool use if it does not work properly or air is leaking.
Tag or mark the tool as ‘defective’ or ‘out of service’ until repaired.
4. Check the manufacturer’s maximum pressure rating for air tools
and accessories. Compressor outlet pressure must be regulated
9081548 PNEUMATIC/HYDRAULIC SHOP PRESS V1.0
Assistance available at www.princessauto.com or 1-800-665-8685 Page 8
to never exceed the maximum pressure rating of the tool (see
Specifications). Exceeding the maximum PSI rating can create a
bursting hazard, causing injury and property damage.
a. The tool does not regulate the pressure level. The power
output is in direct proportion to the air pressure available. An
external air pressure regulator is required to safely use this
tool.
5. Never use oxygen, combustible gas or any other bottled gas as
a power source. Any power source other than an air compressor
could cause an explosion and serious personal injury.
6. Turn OFF the valve and discharge any remaining air pressure after
each use or before adjusting the tool.
7. Do not leave the air tool unattended with its compressed air supply
on. Turn off the compressed air supply and bleed the air tool of any
remaining compressed air before leaving the air tool unattended.
8. Serious injury may occur from loose debris being propelled at
high speeds from the compressed air stream. Always wear OSHA
approved safety glasses to protect the eyes during operation of the
air compressor.
9. Always turn off the air compressor and drain tank pressure
completely before attempting maintenance or attaching air tools.
Release pressure slowly from the system.
10. Do not cover the air vents.
AIR HOSE PRECAUTIONS
1. Inspect the tool's air hose for cracks, fraying or other faults before
each use. Discontinue use if the air hose is damaged or hissing
is heard from the air hose or couplers. Replace the defective air
hose.
2. Do not allow people, mobile equipment or vehicles to pass over the
unprotected air hose. Position the air hose away from high traffic
areas, in a reinforced conduit or place planks on both sides of the
air hose to create a protective trench.
3. Prevent damage to the air hose by observing the following:
a. Keep the air hose behind the tool and out of the tool's work
path.
V1.0 PNEUMATIC/HYDRAULIC SHOP PRESS 9081548
Page 9 Assistance available at www.princessauto.com or 1-800-665-8685
b. Keep the air hose away from heat, oil, sharp edges or moving
parts.
c. Do not wrap the air hose around the tool as sharp edges may
pierce or crack the air hose. Gently coil the hose and either
hang on a hook or fasten with a device to keep hose together
when storing.
4. A damaged or disconnected air hose under pressure may whip
around and inflict personal injury or damage the work area. Secure
the compressor's air hose to a fixed or permanent structure with
clamps or cable ties.
UNPACKING
WARNING! Do not operate the tool if any part is missing.
Replace the missing part before operating. Failure to do so
could result in a malfunction and personal injury.
Remove the parts and accessories from the packaging and inspect for
damage.
ASSEMBLY&INSTALLATION
INSTALL AN AIR COUPLER PLUG
Prepare a standard 1/4 in. NPT coupler plug (sold separately) for use
with your tool.
1. Wrap the external threads of the coupler plug with sealant tape.
a. Wrap tape in a clockwise direction so it will not unravel.
b. Do not tape all the threads. Leave several leading threads
unwrapped for easier alignment.
2. Screw the coupler plug into the tool's air inlet and tighten with a
wrench until snug.
3. Run the compressor at a low volume and check the connection for
air leaks. Do not use the tool until all air leaks are repaired or the
faulty component is replaced.
9081548 PNEUMATIC/HYDRAULIC SHOP PRESS V1.0
Assistance available at www.princessauto.com or 1-800-665-8685 Page 10
Indice
Lingue:
Altri manuali PROPOINT Utensili elettrici
PROPOINT
PROPOINT 8844185 Manuale utente
PROPOINT
PROPOINT 8836363 Manuale utente
PROPOINT
PROPOINT 8843880 Manuale utente
PROPOINT
PROPOINT 9028002 Manuale utente
PROPOINT
PROPOINT 8354482 Manuale utente
PROPOINT
PROPOINT 8727729 Manuale utente
PROPOINT
PROPOINT 8968299 Manuale utente
PROPOINT
PROPOINT 9027525 Manuale utente
PROPOINT
PROPOINT TOOL SHARPENER Manuale utente
PROPOINT
PROPOINT JPC60 Manuale utente
