Prorack K657 Manuale utente
K657
Fitting Kit
EN Fitting Instructions for Basic Carrier
x 4 x 4 x 8 x 2
x 2 x 4 x 4 x 2
x 2 x 2 x 2
Revision No: 1A 1
Fitting Kit K657
MAX kgs (lbs)
W/P WHD
Hyundai
Santa Fe , 5dr SUV 12-+ ZA 75 kgs (165 lbs) 75 kgs (165 lbs)
Santa Fe , 5dr SUV 12-+ EU 75 kgs (165 lbs) 75 kgs (165 lbs)
Santa Fe , 5dr SUV 12-+ NZ 75 kgs (165 lbs) 75 kgs (165 lbs)
Santa Fe Sport, 5dr SUV 13-+ US 75 kgs (165 lbs) 75 kgs (165 lbs)
Santa Fe , 5dr SUV Aug 12-+ AU 75 kgs (165 lbs) 75 kgs (165 lbs)
2
Fitting Kit EN
K657
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
●Use keys to remove covers.
3
Fitting Kit EN
K657
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment.
●Ensure each end of the crossbar is
adjusted equally.
●Set bars to length (refer to the crossbar
instructions for crossbar adjustment).
●Clamps onto flush roof rail. Pins locate on
inside of rail.
4
Fitting Kit EN
K657
●Tighten adjusting screw to 5 Nm (3.7 ft lb).
●Remove plastic clamp block by gripping bar
leg with fingers and push firmly with
thumbs until clamp block drops out behind
leg.
●Remove both pins from each leg. Use
tapered end of spanner located inside left
hand cover to assist.
5
Fitting Kit EN
K657
●Detach foot from leg. Store loose parts in a
safe place.
●Repeat for all legs.
●Select four feet assemblies and match the
left and right assemblies to the left and
right roof rack legs.
●Assemble foot from kit into leg by pressing
it down.
●Ensure foot interlocks with leg.
●Using short capscrew and washer, secure
assembly onto leg (use Hex Screwdriver
supplied with crossbar to assist)
●Do not over tighten.
●Repeat for all legs.
6
Fitting Kit EN
K657
●Use two M5 x 12 mm self tapping screws to
secure the assembly onto the leg.
●Do not over tighten.
●Apply protective strip as shown.
Trim if required.
●It is important to put the clamps in the
correct position on the vehicle.
●Letters refer to the part numbers stamped
on clamps.
●Clamp Part Number:
A = 915A
B = 929A
7
Fitting Kit EN
K657
Fitment
●Locate three holes at each position along
the inside of the roof rails.
●Place crossbars approximately above
these holes on roof rails.
●Ensure back edge of foot sits flush with the
back edge of vehicle roof rail.
●Place one hand on the leg and apply
downward pressure.
●Slide clamp through opening in leg.
8
Fitting Kit EN
K657
●Ensure the pins of the clamps engage
correctly with the holes in the roof rail.
●Thread the coach bolt through the clamp
and the leg.
●Tighten the red plastic knob.
●Ensure the red plastic knob is in the
position shown when fully tightened.
●Do not over tighten.
●Repeat for all four positions.
●Ensure the clamp engages correctly on
inside of roof rail.
●Use keys to fit and lock covers
●Check crossbar is securely attached to the
vehicle.
9
Fitting Kit EN
K657
CAUTION: Recheck all fasteners immediately after
a load is applied to the crossbars.
Regularly check screws are tight.
10
Indice
Altri manuali Prorack Accessori per automobili
Prorack
Prorack K537 Manuale utente
Prorack
Prorack K502 Manuale utente
Prorack
Prorack K911 Manuale utente
Prorack
Prorack PR3097 Manuale utente
Prorack
Prorack K473 Manuale utente
Prorack
Prorack K1187 Manuale utente
Prorack
Prorack K1027 Manuale utente
Prorack
Prorack T84HALF Manuale utente
Prorack
Prorack K346 Manuale utente
Prorack
Prorack K715 Manuale utente
Prorack
Prorack K544 Manuale utente
Prorack
Prorack K607 Manuale utente
Prorack
Prorack K1001 Manuale utente
Prorack
Prorack K038 Manuale utente
Prorack
Prorack K815 Manuale utente
Prorack
Prorack K387 Manuale utente
Prorack
Prorack K777 Manuale utente
Prorack
Prorack P16 Manuale utente
Prorack
Prorack K188 Manuale utente
Prorack
Prorack K835 Manuale utente
