Prosilica GE650 Manuale utente
Prosilica Inc. www.prosilica.com tel: 604.875.8855 fax: 604.875.8856
© 2009 Prosilica Inc. All rig ts reserved.
prosilica
USER MANUAL
July 22, 2009
GE650
GE650C
GE650 User Manual
70-0014A-D
Prosilica Inc.
ii
Table of Contents
Table of Contents............................................................................................................................ ii
Introduction.................................................................................................................................1
Precautions ..................................................................................................................................1
Warranty......................................................................................................................................1
Specifications ..............................................................................................................................2
Supported Features......................................................................................................................3
Mechanical ..................................................................................................................................4
Connections.................................................................................................................................5
Cleaning the Sensor...................................................................................................................10
Adjusting the C-mount..............................................................................................................11
Camera Installation....................................................................................................................12
System Optimization.................................................................................................................17
Trouble Shooting.......................................................................................................................19
Addendum......................................................................................................................................22
GE IO Schematic.......................................................................................................................23
Hirose 12-pin Trigger Schematic..............................................................................................24
Mini-SMB Trigger Schematic...................................................................................................25
Trigger Timing Diagram ...........................................................................................................26
Notes on Triggering...................................................................................................................27
GE650 User Manual
70-0014A-D
Prosilica Inc.
1
Introduction
The GE650 series of cameras are sensitive, 90 frames per second, VGA, Gigabit Ethernet
cameras based on the Sony ICX424AL and ICX424AQ CCD sensors.
Precautions
READ INSTALLATION GUIDE CAREFULLY.
This document contains specific information which is necessary for the correct operation and
treatment of this product.
DO NOT OPEN THE CAMERA. WARRANTY IS VOID IF CAMERA IS OPENED.
This camera contains sensitive components which can be damaged if handled incorrectly.
KEEP SHIPPING MATERIAL.
Poor packaging of this product can cause damage during shipping.
VERIFY ALL EXTERNAL CONNECTIONS.
Verify all external connections in terms of voltage levels, power requirements, voltage polarity,
and signal integrity prior to powering this device.
CLEANING.
This product can be damaged by some volatile cleaning agents. Avoid cleaning the image sensor
unless absolutely necessary. Please see instructions on sensor cleaning in this document.
DO NOT EXCEED ENVIRONMENTAL SPECIFICATIONS.
See environmental specifications limits in the Specifications section of this document.
Warranty
Prosilica provides a 2 year warranty which covers the replacement and repair of all Prosilica
parts which are found to be defective in the normal use of this product. Prosilica will not
warranty parts which have been damaged through the obvious misuse of this product.
GE650 User Manual
70-0014A-D
Prosilica Inc.
2
Specifications
Sensor Type Sony ICX424AL CCD (ICX424AQ for color)
Sensor Shutter Type Progressive Interline
Image Resolution 659 x 493 pixels
Pixel Size 7.4µm x 7.4µm
Optical Format 1/3 inch
Lens Mount C-mount with adjustable back focus
Color Sensor Filter Pattern
†
Bayer
Full Resolution Frame Rate 90 fps
Frame Rate (320 x 240 ROI) 164 fps
I/O 1 isolated TTL compatible input, 3 isolated TTL
compatible outputs, RS-232 input/output
Power Requirements Less than 3.2W
††
. 12V nominal.
Digitization 12 Bits
Trigger latency* 1.1us
Trigger Jitter* ±30ns
Tpd* 90ns
Operating Temperature 0 to 50 Celsius***
Operating Humidity 20 to 80% non-condensing
Size 39mm (height) x 51mm (width) x 80mm (length)
Weight 170g
Hardware Interface Standard IEEE 802.3 1000BASE-T, 100BASE-TX
Software Interface Standard GigE Vision Standard 1.0
Regulatory Conforms to CE, FCC
† Applies to GE650C only.
†† Power consumption will increase with reduced ROI imaging. Add 2.3W for Version A cameras.
††† Nominal operating voltage is 12V. Cameras have been tested at 12V.
* See Notes on Triggering in the Addendum.
***DUE TO THE SMALL PACKAGING AND HIGH SPEED OF THE GE CAMERAS, SPECIAL
CARE IS REQUIRED TO MAINTAIN A REASONABLE OPERATING TEMPERATURE. IF THE
CAMERA IS TO BE OPERATED IN A WARM ENVIRONMENT, IT IS SUGGESTED THAT THE
CAMERA BE MOUNTED ON A HEAT SINK SUCH AS A METAL BRACKET AND THAT
THERE IS SUFFICIENT AIR FLOW.
GE650 User Manual
70-0014A-D
Prosilica Inc.
3
Supported Features
Imaging Modes free-running, external trigger, fixed rate, software trigger
Fixed Rate Control 0.001 fps to maximum frame rate
External Trigger Delay 0 to 60 seconds in 1 microsecond increments
External Trigger Event rising edge, falling edge, any edge, level high, level low
Exposure Time 10 microseconds to 60 seconds in 1 microsecond increments
Gain 0 to 19dB
Region of Interest (ROI)
independent x and y control with 1 pixel resolution
Horizontal Binning 1 to 8 pixels
Vertical Binning 1 to full resolution of sensor
Pixel Formats Mono8, Mono16*, Bayer8, Bayer 16, RGB24,
YUV411, YUV422, YUV444,
BGR24, RGBA24, BGRA24
Sync Out Modes trigger ready, trigger input, exposing, readout, imaging, strobe,
GPO
*On monochrome versions only.
GE650 User Manual
70-0014A-D
Prosilica Inc.
4
Mechanical
79.6*
50
20.1*
26
26
M3
3MM DEEP
6 PLCS TYP
51.3
39.1
All dimensions are in mm.
* Add 0.3mm or color cameras due
to addition o IR blocking ilter.
Figure 1. GE SERIES mechanical dimensions.
GE650 User Manual
70-0014A-D
Prosilica Inc.
5
Connections
1
5
6
2
3
4
7
Figure 2. GE SERIES connection diagram.
GE650 User Manual
70-0014A-D
Prosilica Inc.
6
Ite 1: GIGABIT ETHERNET PORT
This port conforms to the IEEE 802.3 1000BASE-T standard for Gigabit Ethernet over copper.
It is recommended that CAT5E or CAT6 compatible cabling and connectors be used for best
performance. Cable lengths up to 100m are supported.
Ite 2: General Purpose I/O PORT
PIN FUNCTION
1 Trigger Input
2 Sync Out 2
3 Sync Out 3
4 RS-232 RXD
5 RS-232 TXD
6 DNC
7 DNC
8 DNC
9 DNC
10 Isolated Ground
1
2
3
4
5
6
7
89
10
11
12
11 Isolated Ground
Figure 3. General Purpose I/O Pin out. Camera rear view. 12 Isolated Ground
The General Purpose I/O port uses a Hirose HR10A-10R-12SB connector on the camera side.
The mating cable connector is Hirose HR10A-10P-12P. This connector can be purchased from
Prosilica or from http://www.digikey.com.
See Addendum for more detail.
DO NOT EXCEED 5.5V ON SIGNAL INPUTS.
All inputs and outputs are galvanically isolated from the internal camera circuitry.
TRIGGER INPUT
This input signal allows the camera to be synchronized to some external event. The camera can
be programmed to trigger on the rising or falling edge of this signal. The camera can also be
programmed to capture an image at some programmable delay time after the trigger event.
GE650 User Manual
70-0014A-D
Prosilica Inc.
7
Sync Out 2 and Sync Out 3
These signals only function as outputs and can be configured as follows:
Exposing Corresponds to when camera is
integrating light.
Trigger Ready Indicates when the camera will accept a
trigger signal.
Trigger Input A relay of the trigger input signal used
to “daisy chain” the trigger signal for
multiple cameras.
Readout Valid when camera is reading out data.
Imaging Valid when camera is exposing or
reading out.
Strobe Programmable pulse based on one of the
above events.
GPO User programmable binary output.
Any of the above signals can be set for active high or active low.
RS-232 RXD and RS-232 TXD
These signals are RS-232 compatible. These signals allow communication from the host system
via the Ethernet port to a peripheral device connected to the camera.
ISOLATED GROUND
These signals are internally connected to isolated ground. At least one of these signals must be
connected to the users external circuit ground. However, it is good practice to provide a
dedicated ground return for each signal used. For example, a good cable design would connect
the required signal on one conductor of a twisted pair and the isolated ground on the second
conductor of the same twisted pair.
DNC
These signals are reserved for future use and should be left disconnected.
Ite 3: Mini-SMB Trigger Input
The Mini-SMB port on the camera uses an Amphenol 903-406J-51R connector. A suitable
mating cable connector is Amp 413985-3 which can be used with RG174 coaxial cable. Contact
Prosilica to purchase cabling.
The Mini-SMB Trigger Input is internally connected to the Trigger Input (Pin 1) of the General
Purpose I/O Port (Item 2 above). Therefore see this section for more detail.
GE650 User Manual
70-0014A-D
Prosilica Inc.
8
Ite 4: Mini-SMB Sync Out 1
This Mini-SMB port on the camera uses an Amphenol 903-406J-51R connector. A suitable
mating cable connector is Amp 413985-3 which can be used with RG174 coaxial cable. Contact
Prosilica to purchase cabling.
This connector is particularly useful for triggering multiple cameras in a “daisy chain” fashion.
The Sync Out 1 signal can be configured as follows:
Exposing Corresponds to when camera is
integrating light.
Trigger Ready Indicates when the camera will accept a
trigger signal.
Trigger Input A relay of the trigger input signal used
to “daisy chain” the trigger signal for
multiple cameras.
Readout Valid when camera is reading out data.
Imaging Valid when camera is exposing or
reading out.
Strobe Programmable pulse based on one of the
above events.
GPO User programmable binary output.
Any of the above signals can be set for active high or active low.
Ite 5: Status LED 1
LED COLOR STATUS
Solid Green Ethernet link established.
Flashing Green Ethernet activity.
Ite 6: Status LED 2
LED COLOR STATUS
Solid Green Normal operation.
Solid Orange Firmware missing.
Flashing Orange Unrecognizable error.
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Prosilica Macchina fotografica digitale
Prosilica
Prosilica GC750 Manuale utente
Prosilica
Prosilica GS2450 Manuale utente
Prosilica
Prosilica GC1600 Manuale utente
Prosilica
Prosilica GC1380H Manuale utente
Prosilica
Prosilica GE1380 Series Manuale utente
Prosilica
Prosilica GC660 Series Manuale utente
Prosilica
Prosilica GC1020 Manuale utente
Prosilica
Prosilica GC Series Manuale utente
Prosilica
Prosilica EC655 Manuale utente
Prosilica
Prosilica GC1290C Manuale utente
