ProStart CT-3471 TW Manuale utente

TWO-WAY 6-BUTTON LCD AUTOMATIC/MANUAL TRANSMISSION

REMOTE STARTER

CT-3471 TW

User Guide

WARNING

It is the responsibility of the vehicle operator to ensure their vehicle is parked

in a safe and responsible manner.

1. a) Manual transmission: When leaving the vehicle, it is the user’s

responsibility to ensure that the gearshift lever is in the NEUTRAL position and

the parking brake is engaged in order to avoid accidents upon remote starting.

b) Automatic transmission: When leaving the vehicle, it is the user’s

responsibility to ensure that the gearshift lever is in “Park” in order to avoid

accidents upon remote starting.

(Note: Make sure that the automatic vehicle cannot start in "Drive".)

2. It is the user's responsibility to ensure that the remote starter is disabled or put

into valet mode before servicing.

A note concerning the battery inside the transmitter:

Depending on your usage of the transmitter, the battery can last anywhere between 3 to 6 months. When the

battery is low, the transmitter will produce two beeps in a repetitive cycle. At that point you should replace

your battery with a new one. That is why we recommend that you keep a spare battery somewhere handy

such as the glove compartment.

INDUSTRY CANADA USER NOTICE:

Operation is subject to the following two conditions: (1) this device may not cause interference, and (2)

this device must accept any interference, including interference that may cause undesired operation of

the device.

To reduce potential radio interference to other users, the antenna type and its gain should be so chosen

that the equivalent isotropically radiated power (EIRP) is not more than that required for successful

communication.

NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized

modifications to this equipment. Such modifications could void the user's authority to operate the

equipment.

P.2 User Guide

TABLE OF CONTENT

INTRODUCTION .......................................................................................................................3

WHAT IS “ESH”TECHNOLOGY?........................................................................................................3

VEHICLE PRESETS..........................................................................................................................3

HEATER..........................................................................................................................................3

WINDSHIELD WIPERS &RADIO &HEADLIGHTS...................................................................................3

USING THE REMOTE CONTROL.....................................................................................................3

LCDREMOTE FUNCTIONS................................................................................................................3

BASIC VEHICLE OPERATIONS............................................................................................................4

TRANSMITTER MODE SELECTION ......................................................................................................5

HOW TO ACCESS REMOTE’S FUNCTION MENUS:...................................................................................5

TIMER COUNTDOWN ADJUSTMENT....................................................................................................5

ARMING AND DISARMING THE STARTER KILL...........................................................................6

REMOTE-STARTING YOUR VEHICLE.............................................................................................7

SETTING YOUR VEHICLE INTO READY MODE......................................................................................7

REMOTE-STARTING..........................................................................................................................8

DRIVING OFF...................................................................................................................................8

REMOTE STARTER FEATURES......................................................................................................8

REMOTE DOOR LOCKS.....................................................................................................................8

REMOTE TRUNK RELEASE................................................................................................................8

IDLE MODE......................................................................................................................................8

VALET MODES.................................................................................................................................9

PANIC MODE.................................................................................................................................10

QUICK LOCKOUTTM........................................................................................................................10

COLD WEATHER MODE..................................................................................................................10

EXTENDED RUN TIME.....................................................................................................................11

LEDFLASHING..............................................................................................................................11

CONSTANT OUTPUT........................................................................................................................11

MISSING A START OR A STOP CONFIRMATION........................................................................12

ADVANCED FEATURES: INSTALLATION-PROGRAMMABLE OPTIONS..................................12

IGNITION-CONTROLLED DOOR LOCKS..............................................................................................12

SECURE LOCK...............................................................................................................................12

SAFE START..................................................................................................................................13

ENGINE RUN TIME.........................................................................................................................13

TURBO MODE................................................................................................................................13

“HOME VALETTM”MODE.................................................................................................................14

AUX1..........................................................................................................................................14

MULTI-CAR OPERATION..................................................................................................................14

OEM-STYLE ALARM......................................................................................................................15

INTRUSION CODES VIA HORN...........................................................................................................15

MULTI-LEVEL FEATURES .............................................................................................................16

TROUBLESHOOTING POOR TRANSMITTING RANGE...............................................................17

PARKING LIGHT FLASH TABLE...................................................................................................18

PROSTART LIMITED LIFETIME WARRANTY...............................................................................19

User Guide P.3

Introduction 

This is a state-of-the-art remote car starter system. The system is packed with advanced features

such as priority access to the driver’s door (commodity features), the Safe Start children safety

feature and SmartStart™.

SmartStart™ is a groundbreaking technology that enables your remote starter features to be

accessed by your smartphone. Features include keyless entry, trunk release, panic, remote

start/stop toggle and alarm notifications1. Note: SmartStart™ must be professionally installed. For

more information, see your nearest authorised Directed Canada dealer.

With many advanced functions, this product will satisfy any one of your expectations from high-end

commodity and security systems, without neglecting any standard feature commonly offered by

entry-level starters.

Whatis“eSH”Technology?

"eSH" technology uses Manchester decoding, along with advanced custom data filters, to help

reduce data-bit transfer errors. This filtering mechanism minimizes dropped commands by the

transceiver and develops more reliable range. By using narrow band filtering and unique software

driven noise filters, the radio set is able to achieve much better input sensitivity resulting in up to

2,000 feet of operating range.

VehiclePresets

Heater

When leaving the vehicle it is recommended to preset the accessory controls in preparation for the

next remote start. Settings for the blower motor (fan), front and rear, should not be left on HIGH. It

is recommended to leave the settings on LOW or MEDIUM instead.

WindshieldWipers&Radio&Headlights

Certain vehicles require the radio and / or windshield wiper and / or headlight circuits to become

energized while running under remote start. When leaving the vehicle you must ensure that the

windshield wiper and headlight switches are OFF. Leaving the headlight switch ON on certain

types of vehicles could cause them to remain ON even after remote starter shut down, resulting in

a dead battery.

UsingtheRemoteControl

Your remote car starter is equipped with a 6-button multi-channel remote control. It can operate

two independent vehicles equipped with a remote car starter.

LCDRemoteFunctions

The transmitter offers several command-confirmation and timer features. This section explains

some of the key functions available. The next section gives a summary of the button combinations

used to access the functions.

1Certain conditions apply. See your authorized Directed Canada dealer.

P.4 User Guide

Note: If you wish to exit a function while still in the process of accessing it, simply stops and wait at

least 10 seconds: the transmitter will return to its normal state.

The functions of the transmitter are as follows:

BasicVehicleOperations

Function

Button pressed

Icon

Sound

Instructions

description

Lock

1 beep Lock and arm the starter kill

Unlock 2 beeps Unlock and disarm the starter

kill

Trunk or aux 3 1 beep Trunk output

Start *

(see runtime

options below) + Melody Start the engine

Stop None Melody Stop the engine

Back light On for 5 seconds Press once

Cold weather + 1 beep See Cold Weather Mode

section

Remote valet + 1 beep See Vale mode section

Panic None 1 beep See Panic Mode section



Function Button:

. Turns On the backlight

. For accessing Multi-level

functions

UNLOCK Button:

Unlocks all Doors and

disarms the Starter Kill TRUNK Button:

Activates the Trunk

output (AUX3)

LOCK Button:

Locks all Doors and

arms the Starter Kill

START/STOP Button:

Starts or Stops the engine (Normal

functions

)

uxiliary Button:

•Activates

Panic Mode

User Guide P.5

TransmitterModeSelection

Function

Button pressed

Icon

sound

Instructions /description

Vibration mode Press and hold

and then press Vibrates 4x

larm clock mode

on/off + Melody

zPress once to have

alarm clock on

zPress twice to have

alarm clock off

Howtoaccessremote’sfunctionmenus:

User

Transmitter

1.Press until the remote beeps once Îappears on screen.

2.Press a 2nd time for 2 second and release ÎRemote beeps once and

appears on screen.

3.Press a 3rd time for 2 second and release ÎRemote beeps once and

appears on screen.

4.Press and hold button a 4th time until 2

beeps are heard. ÎYou have now accessed the first

function of the remote.

Press the button to toggle between remote’s functions menu:

a. Press the button to increase the value or to activate or deactivate a function or to toggle

through the melodies.

b. Press the to decrease the value or to activate or deactivate a function or to toggle through the

melodies.

c. To save modifications, do not touch any buttons for approx 5 to 10 seconds. There will be a

beep and the display will return to the time.

Function Menu Table:

Function 1:

djust clock time (hour and

minutes) Function

5: Timer

countdown

Function 2:

djust alarm clock (hour and

minutes) Function

Melody selection for timer

countdown

Function 3:

Melody selection for the alarm

Function

Turn ON/OFF timer

countdown

Function 4: Turn ON/OFF alarm cloc

TimerCountdownAdjustment

By pressing Icon

Sound

Instructions / description

+ 1st time

Melody 10 min parking countdown mode

+ 2nd time

Melody 20 min parking countdown mode

+ 3rd time

Melody 30 min parking countdown mode

+ 4th time

Melody 60 min parking countdown mode

+ 5th time

Melody 90 min parking countdown mode

+ 6th time

Melody 120 min parking countdown mode

+ 7th time

Melody Parking countdown off mode

P.6 User Guide

Once the Countdown is activated it will continue counting down until reaching 0:00. If the Timer has not

reached 0:00 and you are starting the vehicle, you should reset your Countdown Timer to 0:00 before starting

your vehicle as to avoid being startled.

ArminganddisarmingtheStarterKill

This added security feature will prevent the vehicle from starting with the Ignition key when the

starter kill is armed. If the system was installed with the starter kill option, you will not be able to

start the vehicle with the key unless the system has been unlocked first or put into Valet Mode

(page-9).

Note: If the Starter Kill is installed, the vehicle will benefit from a protection against starter

motor damage that could occur after remote-starting the engine should the user, by force of

habit, turn the ignition key to the CRANK position.

The Starter Kill (if installed) can be configured by the installer either to Passive Mode (so as to arm

automatically) or Active Mode (so as to require the user’s intervention for arming). By default, your

Remote Car Starter is configured to Passive Mode.

Passive mode:

To arm the Starter Kill, press the button on the transmitter, OR

1. In Passive Mode, the Starter Kill will automatically arm 1 minute (by default) or 3

minutes (if configured this way) after the ignition is turned OFF or once the last door is

closed (if the doors are monitored).

2. The LED on the antenna will flash quickly during the countdown preceding the activation

of the Starter Kill.

3. Once the activation countdown expires, the LED will send a series of quick double

flashes to indicate that the Starter Kill is now armed.

To disarm the Starter Kill, press the button on the transmitter.

•The Starter Kill will automatically rearm itself after 1 minute (by default) or 3 minutes (if

configured this way) if no door is left opened (if the doors are monitored) and the ignition

is not turned ON.

Active Mode:

To arm the Starter Kill, press the button on the transmitter.

1. The parking lights will flash once.

2. The LED on the antenna will flash slowly.

3. If remote door locks are installed, this will also lock the doors and arm the OEM-style

alarm.

To disarm the Starter Kill, press the button on the transmitter.

1. The parking lights will flash twice.

2. The LED on the antenna will remain OFF.

3. If remote door locks are installed, this will also unlock the doors.

User Guide P.7

RemoteStartingYourVehicle

SettingYourVehicleIntoReadyMode

If your vehicle has a manual transmission you must read the following indications. The unit must

first be set to Ready Mode in order to start the vehicle by remote. If the unit is not set to Ready

Mode, it cannot remote start the vehicle.

Please note that Ready Mode can be enabled by the remote or the handbrake, depending on the

option that was selected by your installer. Therefore, you must follow the appropriate procedure

between the two described below in order to set your vehicle into Ready Mode.

Once the system is set to Ready Mode, the vehicle can be remote started and stopped at any time.

The system will exit Ready Mode if a door, the hood or the trunk is opened, if the brake pedal is

pressed, if the parking brake is disengaged or if the ignition key is turned to the IGNITION ON

(RUN) position.

To set the system to Ready Mode:

If Ready Mode is enabled by remote

If Ready Mode is enabled by handbrake

1. Ensure that all the doors, hood and trunk are closed. Make sure that the gear selector is in the

neutral position.

2. With the engine already running, apply the

parking brake once and release the brake

pedal.

2. With the engine already running, apply the

parking brake twice within 10sec.

Make sure to release the brake pedal.

The parking lights will flash 3 times quickly

and remain lit.

Skip to step 4.

3. Within 20 sec. of engaging the parking

brake, press and hold , or on

the transmitter.

The parking lights will flash 3 times quickly

and remain lit.

4. Remove the key: the engine will continue running.

5. Exit the vehicle and close all doors, hood and trunk.

6. Press for approx. 1 second either:

•to lock the doors and shut down the engine;

•to unlock the doors and shut down the engine;

•to shut down the engine without affecting the doors.

7. The icon will appear on your screen.

P.8 User Guide

Remotestarting

1. Press the button. The remote will beep once.

2. Approximately 5 seconds later, the remote will play a start melody to confirm the

remote starter’s activation.

If your vehicle has an automatic transmission and it does not start at the first attempt, the system

will shut down, wait a few seconds and try to start the engine again. There will be 3 start attempts

before the system gives up.

DrivingOff

With the vehicle running under remote control, press the button to disarm the starter kill (if

installed) and unlock the doors. Enter the vehicle and do the following:

•Turn the ignition key to the IGNITION ON (RUN) position. (Do not turn the key to the CRANK

position while the engine is running. This would cause the starter motor to re-engage.)

•Press the brake pedal to disengage the remote starter unit.

You are now ready to drive off.

RemoteStarterFeatures

RemoteDoorLocks

If your system was installed with the Remote Door Locks option, you will have the convenience of

remote keyless entry.

To lock your doors and arm the starter kill (if installed):

1. Press and hold the button for approx. 1 sec.

2. The remote will beep once then display the icon to confirm that the doors have been

locked.

To unlock your doors and disarm the starter kill (if installed):

1. Press and hold the button for approx. 1 sec.

2. The remote will beep twice then display the icon to confirm that the doors have been

unlocked.

RemoteTrunkRelease

If your system was installed with the Remote Trunk Release option, you can open your trunk by

pressing the button until the remote displays on the screen. In addition, this will also

disarm the OEM style alarm.

IdleMode

Convenience feature: Idle Mode allows you to keep the engine running and the doors

locked while you stop, for example, at a convenience store or for a short delivery.

This feature allows you to let the remote starter take over control of the vehicle (i.e. no Key in the

Ignition Switch) while the engine is running.

If your vehicle has an automatic transmission, proceed as follows to set the system to Idle

Mode:

User Guide P.9

1. With the engine running, make sure to release the brake pedal and press the , or

button on the transmitter until the parking lights come ON.

2. Remove the ignition key from the ignition switch.

The engine will continue running.

3. Exit the vehicle and close all doors, hood and trunk.

4. Press the button to lock the doors, to arm the starter kill and to arm the OEM style

alarm.

If your vehicle has a manual transmission, Idle Mode can be activated through the same routine

as that used for Ready Mode (page-7); at the last step, press button to lock the doors, arm the

system and leave the engine running.

Note1: The engine will continue running until the user re-enters the vehicle or until the expiration of

the engine run time.

Note2: If the pre-programmed run-time expires or if the user shuts down the engine by remote

control, the vehicle will enter Ready Mode.

Caution!!! Do not leave children or pets unattended in a vehicle standing in Idle Mode.

ValetModes

When the vehicle is in Valet Mode, the remote starter and alarm functionalities are disabled. If the

vehicle needs to be serviced, or if you park it indoors, the Valet Mode will prevent the engine from

being remote-started accidentally.

Any of the following features will put your remote car starter into Valet Mode:

Ignition Valet: This feature allows you to put your system into Valet Mode by using the

ignition key.

Remote valet: This feature allows you to put your system into Valet Mode by using the

transmitter.

ToputthesystemintoValetMode

To put the system into Valet mode using the KEY (Ignition Valet Mode):

1. Insert the ignition key into the ignition switch. Within 10 sec., turn the key 5 times

successively into the IGNITION/RUN and OFF positions.

2. The parking lights will flash three times.

3. Turn the ignition OFF.

4. The LED on the antenna will come ON solid to indicate that the vehicle has successfully

entered Valet mode.

5. The icon will appear on your LCD remote.

To put the system into Valet mode using the TRANSMITTER (Remote Valet Mode):

1. Press the and buttons simultaneously until the icon will appear on your LCD

remote.

2. The LED on the antenna will come ON solid to indicate that the vehicle has successfully

entered Valet mode.

P.10 User Guide

TotakethesystemoutofValetMode

To take the system out of Valet mode using the KEY (Ignition Valet Mode):

1. Insert the ignition key into the ignition switch. Within 10 sec., turn the key 5 times

successively into the IGNITION/RUN and OFF positions.

2. The parking lights will flash twice.

3. Turn the ignition OFF.

4. The LED on the antenna will flash quickly to indicate that the vehicle is now out of Valet

mode.

5. The icon will disappear on your LCD remote.

To take the system out of Valet mode using the TRANSMITTER (Remote Valet Mode):

1. Press the and buttons simultaneously until the icon will disappear from your

LCD remote.

2. The LED on the antenna will flash quickly to indicate that the vehicle is now out of Valet

mode.

The system will warn you if someone attempts to remote start the vehicle while in Valet Mode:

The parking lights will:

Turn ON then OFF; then

Flash twice.

PanicMode

Note: Panic mode can only be activated if the horn has been adequately configured by the

installer.

In an emergency situation, you can activate panic mode by pressing and holding the AUXILIARY

BUTTON until the horn starts honking. If the vehicle is under a remote start, the engine will

shutdown automatically before setting off the horn. You can stop the horn by pressing:

(this will lock your doors and deactivate panic mode), or

(this will unlock your doors and deactivate panic mode).

Furthermore, the panic mode can be stopped by activating Valet Mode (page-9)

* Panic Mode will automatically shut down after 30sec.

QuickLockoutTM

(Also called Secure Panic.) For fast protection in emergency situations, the system will LOCK all

doors when you press the brake pedal while you hear the sound signal. (Quick Lockout is only

available when panic mode has been set off.)

ColdWeatherMode

If the vehicle has a Manual transmission, Ready mode (page-7) should be set before entering

Cold Weather. When cold weather mode is active, the engine starts every 2 hours and runs for 3

minutes (or for 8 or 20 minutes with diesel engines). Cold weather mode automatically ends after

24 hours. The vehicle must be set in ready mode (manual transmission) before the cold weather

mode can be activated.

To enter Cold Weather Mode:

1. Press the for 1 second and release. The remote will beep once and will

appear on the display.

2. Press and hold the button until the icon will appear on the display.

Altri manuali per CT-3471 TW

Indice

Altri manuali ProStart Avviamento remoto

ProStart

ProStart CT-5072 Manuale utente

ProStart

ProStart CT-3400 TW Manuale utente

ProStart

ProStart ProStart CT-3360 Manuale utente

ProStart

ProStart CT-3271 Manuale utente

ProStart

ProStart CT-5000 Manuale utente

ProStart

ProStart CT-3200 Manuale utente

ProStart

ProStart CT-3371 Manuale utente

ProStart

ProStart CT-3471 TW Manuale utente

ProStart

ProStart CT-3271 Manuale utente

ProStart

ProStart CT-5072 Manuale utente

ProStart

ProStart CT-4311TW Manuale utente

ProStart

ProStart CT-3100 Manuale utente

ProStart

ProStart CT-5000 Manuale utente

ProStart

ProStart CT-4211TW Manuale utente

ProStart

ProStart CT-3460 TW Manuale utente

ProStart

ProStart CT-3371 Manuale utente

ProStart

ProStart 034-0843-4 Manuale utente

ProStart

ProStart CT-3400 TW Manuale utente

ProStart

ProStart ProStart CT-5460TW Manuale utente

ProStart

ProStart CT-3271 Manuale utente

Manuali Avviamento remoto popolari di altre marche

AstroStart

AstroStart 803U Manuale utente

Durite

Durite 0-649-20 Manuale

EINHELL

EINHELL BT-PS 1000 Manuale

Linear

Linear ACCESS AK-21 Specifiche tecniche

Soundstream

Soundstream TARANTULA RS.2 Manuale utente

Jaycar Electronics

Jaycar Electronics MB3752 Manuale utente

Ultra Start

Ultra Start 72 Series Manuale utente

ADS

ADS FLASHLOGIC FLRSVW1 Manuale utente

Selecta

Selecta JS012 Manuale utente

Black Widow Security

Black Widow Security BW RAS 400 Manuale utente

Vector

Vector Power City DK080706 Supplemento

Code Alarm

Code Alarm CA-535 Manuale utente

Ozito

Ozito OJS-800 Manuale utente

Profi-Partner

Profi-Partner 46387 Manuale utente

EZ STARTER

EZ STARTER EZ-45 Manuale utente

Viper

Viper 4204 Manuale utente

Essex Electronics

Essex Electronics KE-1701 Manuale utente

EINHELL

EINHELL EGS 3600 Manuale