Proteus LDT-8850 Manuale utente
Testing specification :
EN 957-1, EN 957-6.
rd
he GS Mark is a voluntary 3 party inspection and certification scheme for finished products only,
..
according to German Equipment Safety Law - Geratesicherheits - Gesetz.
This label ensures products strictly meet the technical safetyrequirements as stipulated by the GSG
and the current production line is audited.
Features of product with GS-TUV mark :
Mechanical and electrical safety. Symbol of high quality. Reliability assurance.
assigned SGS-TUV Taiwan and Rheinland Taiwan for its range of products to apply
the GS-TUV testing.
Index
INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Introduction / Safety Guideline
Maintenance
Information
Parts List
Exploded Drawing
Parts List
Assembly - Base
Upright Tube Assembly
Assembly - Air Pressure Shaft
Assembly - Monitor
Assembly - Cover
Folding
Adjust The Machine
Mat Alignment
Incline
Pulse
LDT-8850 Monitor
Monitor Functions
About Display
Operation Instructions
Program Function
Program Profile
Warm - Up
01
02~03
04
05~07
08
09
10
11
12
13
14
15
16
17
18
19
20
21~25
26~29
30~34
35~40
41~42
43~44
01
1 INTRODUCTION
Thank you very much for choosing PROTEUS products. To secure the safety, pls read the manual and
all suggestions carefully before using the product. While you get everything ready, believe that you
could enjoy the pleasure of exercise and healthy.
2. SAFETY GUIDELINE
Before starting any exercise program consult your Physician.
*Read this users manual and follow the instructions.
*Do not allow children to play on the treadmill.
*Keep the safety key out of reach of the children.
*Inspect the treadmill before use and ensure the power cord is not damaged.
*Place the treadmill on a solid level surface with the rear and side away from any objects.
*Keep hands away from moving parts.
*Do not place any liquids on or near the treadmill.
*Wear appropriate clothing and shoes for exercise.
*Do not wear shoes that will damage the mat.
*Stop your exercise if you feel any pain or abnormal sensations and consult your Physician
*
immediately.
Place both feet on the foot rails before starting the treadmill.
*Do not start the treadmill when you are standing on the mat.
*If you have any questions or concerns, contact dealer.
*Make sure the ground-wire installed, before assemble the machine.
*This is home fitness equipment, not suitable to other place.
*
Introduction / Safety guideline
3 MAINTENANCE :
a. Maintenance
1. Clean and lubricate the bed of the treadmill every 20 hours of use or monthly, which ever
comes first ( SEE TREADMILL LUBRICATION INSTRUCTIONS ). Daily cleaning to the sides
of the running mat will prevent much of the dirt from getting underneath the mat.
2. Prevent the build up of dust beneath the motor cover and under the treadmill body ( any work
involving the removal of the motor cover should be carried out by a qualified technician ). The
surface around and beneath the treadmill should be cleaned weekly. Less dust and dirt
underneath the machine means that less gets into it. Select a floor covering that is not
subject to the build up of dust and also protects the original floor surface.
3. Ensure that fluids are not spilt on the treadmill console or running mat.
4. Have the treadmill serviced. Call your dealer for assistance.
b. Treadmill clean and lubrication instruction
1. Using a clean towel, slide it between the running mat and the bed of the treadmill, at the motor
end, so that one end of the towel hangs over each side of the machine.
2. Grasp each end of the towel and gradually pull it back towards the rear of the machine. ( make
sure the mat does not move ).
3. When you reach the rear roller, push the MAT and towel to the motor end so the towel is back
near the motor cover. Repeat steps 2 and 3 twice. This action cleans the mat and deck of the
treadmill.
4. Take the container of lubricant and apply to the treadmill bed.
5. Walk on the treadmill for two minutes at about 5 km/h, to spread the lubricant.
02
Maintenance
03
6. Mat slippage may be occurred for a short time. If it persists, adjust the running mat tension as
per direction in the owner's manual ( adjust belt tension ). Do not over-tighten, as this will
decrease the life of the mat and place undue stress upon the roller bearings.
7. If you are uncertain of any procedure or lack
of correct tools, please contact your dealer.
We recommend a qualified technician
carry out work involving removal of the
motor cover.
c. Silicon
Silicon spray warning
KEEP OUT OF REACH OF CHILDREN !
If swallowed or sprayed directly on face, seek medical advice immediately.
If spilt, clean up immediately, as slippage hazard may result.
Note : This product may cause damage or loss if used otherwise than strictly in accordance
with the directions for its use.
This product is sold only subject to these conditions and upon the basis that it is used solely at the
purchaser's own risk and the manufacturers and distributors hereby exclude themselves from all
liability in relation to this product howsoever arising.
Maintenance
( clean ) ( instruction )
04
4¡EINFORMATION¡GLDT-8850
a Company information
Proteus Sports Lnc.
Address: 77-3, Nanshin Village, Linkou, Taipei Hsien, Taiwan, R.O.C.
Tel : + 886-2-26093940 26090836
Fax : + 886-2-26093862 26002921
http : //www.proteusfitness.com
Information
Basic spec :
Machine size 190 x 85 x 159cm Electric spec AC 110V 60Hz / 220V50Hz
Folded size 113 x 85 x 159cm Speed range 1km/h ~ 18 km/h
Running surface 50 x 140cm Motor 2.5HP 4000RPM
Thickness of running belt 1.8mm
Thickness of running deck 25.4mm
Machine base section Square tube(40x80) Elevation type Elevation motor
( stepless/16 levels )
Upright tube section Square tube(40x80) Elevation angle 0°~5.5°
Painting Black powder-body Max. user weight 150kg
weight 105kg Folding Foldable
05
LDT-8850 PARTS LIST
1 Main frame 1
2 Cushion 8
3 Square tube cap 6
4 Foot unit 2
5 Front roller set 1
6 Rear roller set 1
7 Motor 1
8 V- belt 1
9 M8 screw 4
10 M8 washer 8
11 Semicircle Hex. screw 3
12 Air Pressure shaft 2
13 Under cover for rear roller ( L ) 1
14 Under cover for rear roller ( R ) 1
15 Top cover for rear roller ( L ) 1
16 Top cover fro read roller ( R ) 1
17 Washer 52
18 Round-headed screw 6
19 Running board 1
Parts List
No. Description Q'ty No. Description Q'ty
20 Side rail 2
21 Running belt 1
22 Rear complete cover 1
23 Front complete cover 1
24 Side Rail fix plate 8
25 Incline socket set 1
26 Bushing 2
27 Hex. screw 2
28 Horizontal shaft for base 1
29 Horizontal shaft for base cover 2
30 Motor cover 1
31 Round-headed screw 4
32 Up right tube unit ( left ) 1
33 Up right tube unit ( right ) 1
34 Washer 16
35 Semicircle Hex. screw 10
36 Semicircle Hex. screw 3
37 Handlebar cover ( outside, left ) 1
38 Handlebar cover ( inside, left ) 1
06
Parts List
No. Description Q'ty No. Description Q'ty
39 Handlebar cover ( inside, right ) 1
40 Handlebar cover ( outside, right ) 1
41 Big flat spider screw 6
42 Top handle bar 1
43 Hex. Screw 2
44 Control board 1
45 Wave filter 1
46 Inductor 1
47 Elevation motor 1
48 Power socket 1
49 Thermo switch 1
50 Power switch 1
51 Base assembly 1
52 Wheel 4
53 Semicircle Hex. Screw 11
54 Nut jacket 2
55 Console combined plate 2
56 Round-headed spider screw 4
57 Console assembly 1
58 Semicircle Hex. Screw 8
59 Console elbow 1
60 Monitor case 1
61 Monitor 1
62 Safety key 1
63 Front cover for base 2
64 Square tube cap 1
65 Retractable outer tube 1
66 Spring pin 1
67 Hollow cap 1
68 Retractable inner tube 1
69 Inner cap for square tube 1
70 Inner cap for round tube 4
71 Fixed socket for water cup 1
72 Nylon anti-loose nut 9
73 Hand pulse sensor 2
74 Hex. Screw 1
75 Nylon anti-loose nut 1
76 Round-headed screw 2
No. Description Q'ty
Parts List
77 Washer 3
78 Spring washer 4
79 Semicircle Hex. screw 8
80 Plastic washer 2
81 Foam grip 2
82 PROTEUS plate 1
83 Fix base for pulse wire 1
84 Sensor shaft 1
A Control wires in upright tube 1
B Elevation wires in upright tube 1
C Hand pulse sensor wires 1
D Control wires on console 1
E Elevation wires on console 1
F Wires on console 1
07
Indice
Altri manuali Proteus Tapis roulant
