Protocol Dronium Two AP Manuale utente
INSTRUCTION MANUAL
dronium TWO AP
DRONE with camera
TM
WWW.PROTOCOLNY.COM
Thank you for your purchase of Protocol’s Dronium Two AP
With Camera. You are about to experience the best of what
remote control ight has to oer. We strongly recommend
that you take the time to read this manual thoroughly. It
contains many tips and instructions on how to get the most
out of this aircraft and maintain it for a long life.
As with any aircraft, this is a precision ying machine. Treat
it well and enjoy all the fun it has to oer, ight after ight.
THANK YOU.
TABLE OF CONTENTS
01 Safety & Precautions
02 Parts
05 Remote Battery Installation
06 Installing the Blade Guard & Landing Gear
07 Charging the Drone
09 Power-On Procedure
10 Operation - Mode 1
12 Operation - Mode 2
14 Tips on 360° Flips
15 Speed Modes
16 Trim Adjustment - Mode 1
17 Trim Adjustment - Mode 2
18 Troubleshooting
19 Flying Outdoors
20 Shooting Photo/Video
21 Replacement Parts & Limited Warranty
�
Read and follow instructions on how to synchronize
electronics before each flight.
�
To prolong engine life, allow a cool-down period between flights.
1
REMOTE
1. Antenna
2. Indicator Light
3. 3D Stunt
4. Right Direction Lever (4-way directional)
5. Trim Forward/Backward
6. Mode Switch/ Trim Bank Left/Right (Mode 1)
a. Trim Turn Left/Right (Mode 2)
7. LCD Display
8. Trim Turn Left/Right (Mode 1)
a. Trim Bank Left/Right (Mode 2)
9. Photo/Video
10. Throttle/Turn Left/Right
11. Power Switch
12. Speed Mode Selector
PARTSPARTS
DRONE
1. Canopy
2. Blade
3. Blade Guard
4. Landing Gear
5. Battery Compartment
6. Camera
23
REMOTE BATTERY INSTALLATION
1. Install batteries carefully.
2. Do not mix old and new batteries.
3. Do not mix dierent types of batteries.
Unscrew and remove battery cover from controller. Insert 4 x ‘AA’ batteries
according to indicated polarities. Replace and screw back in battery cover.
45
PARTS
LCD SCREEN
01. Trim: Side-to-side Banking (defaults to center on start-up)
02. Trim: Forward/Backward (defaults to center on start-up)
03. Trim: Turn Left/Right (defaults to center on start-up)
04. Throttle (remains at center)
05. Throttle (defaults to zero on start-up)
06. Directional Display (defaults to center on start-up)
07. Banking Movement to Right
08. Backward Movement
09. Banking Movement to Left
10. Right Turn Movement (defaults to zero on start-up)
11. Left Turn Movement (defaults to zero on start-up)
12. High Speed Mode Active
13. Low Speed Mode Active
14. Controller battery Level Indicator
15. Flight Mode 1 Active (Default); To change to Mode 2, press and
hold Mode Switch to the right while turning on the transmitter.
16. Remote control signal strength
17. Indicates positive communication lock with the Dronium Two AP
4 x ‘AA’ Batteries
Battery Cover
If not already installed, install the included blade guards to every corner
and tighten the screws. Make sure the blade guards are secure and snug.
NOTE: Loose blade guards may interfere with propeller movement and
cause a crash. If the drone crashes, double check to make sure the blade
guard is not loose. If it is, re-tighten before ying.
INSTALLING THE BLADE GUARD & LANDING GEAR
1. Push the on/o switch of the drone to OFF and open the battery cover.
2. Pull out the battery wire from the power port.
3. Connect the USB charging cable to the battery wire.
4. Plug the charger into a USB port. The USB will light up while charging
and will turn o once fully charged.
5. Reconnect the battery wire to the power port and close the battery cover.
Charging time: approximately 75 minutes --- Flying time: approximately
7 minutes
CHARGING THE DRONE
*Battery: Li-Po, 7.4V, 350mAh
If you purchased extra batteries, allow the engines to cool between ights in
order to prolong engine life.
If not already installed, install the included landing gear.
67
POWER-ON PROCEDURE
NOTE
1. While the drone is in process of synchronizing, the lights will ash.
When the process is completed, the lights will remain steady. This is
your indication that the process is completed.
2. If after 30 seconds, it has not recognized the drone, turn o the
controller and repeat Power-On prodedure.
Before ying, the drone and transmitter must be turned on in sequence and
synchronized.
1. Turn on the drone and place it on an even surface.
2. Turn on the remote control.
3. Both indicators on the drone and the remote will ash.
4. Push the throttle up and then down to sync. You will hear two beeps and
the lights will go steady.
Tip: When syncing your drone keep it in a horizontal position for stable ight.
CHARGING THE DRONE BATTERY
CAUTION WHEN CHARGING
1. When charging, place product on a dry, well-ventilated surface and
keep away from heat sources.
2. Always use adult supervision while charging.
3. In order to increase battery longevity, avoid repeat charging and
excessive discharging.
4. As battery temperature is high immediately after ight, charge after
cooling down for higher eciency.
5. Do not strike or subject battery to hard impacts or sharp surfaces.
6. Do not use any other charger than that which is supplied with
this item.
7. Do not use or leave battery near a heat source such as re or space
heater; exposure to heat may result in reduced performance or in
some cases dangerous conditions.
8. If battery is left in charging state for an extended period of time after
being fully charged, the battery may automatically discharge.
9. Never leave the battery unattended during charging.
10. Do not disassemble battery.
11. Do not submerge battery in water.
89
OPERATION (MODE 1)
FIRST TIME FLYERS!!! TAKE YOUR TIME! GO SLOW!
Practice hovering until you are comfortable with ight before attempting
any other maneuvers. Make small movements letting the stick return to
the center. If you start to lose control, don’t panic. Just press land.
STARTING THE ENGINE; ENGINE IDLE
1. After synchronizing the drone, gently push the throttle up and release to
go into idle mode.
OR
2. Pull the throttle and direction sticks to the center at the same time and
release to go into idle mode. The blades will rotate but the drone will
not lift.
TAKE-OFF
1. Gently advance the throttle up to a desired height and release. The drone
will hover at that height.*
LANDING
1. Push down on the throttle until the drone is on the ground.
Pull the throttle left or right,
the drone turns to the left or right.
Push the direction lever up or down,
the drone ies forward or backward.
Pull the direction lever to the left or right,
the drone banks to the left or right.
10 11
OPERATION (MODE 1)
NOTE:
- The engine will shut o if you choose to hold the throttle down for
3 seconds.
- EmergencyShutO:Wheninight,
pull the throttle and direction stick
to the center at the same time and
thedronewillshuto.
* The drone may drift a bit, especially in the rst 30 seconds until the
altitude sensor gets a good x on the position. Some drift is normal.
OPERATION (MODE 2)
Pull the throttle left or right,
the drone banks to the left or right.
Push the direction lever up or down,
the drone ies forward or backward.
OPERATION (MODE 2)
12 13
STARTING THE ENGINE; ENGINE IDLE
1. After synchronizing the drone, gently push the throttle up and release
to go into idle mode.
OR
2. Pull the throttle and direction sticks to the center at the same time and
release to go into idle mode. The blades will rotate but the drone will
not lift.
TAKE-OFF
1. Gently advance the throttle up to a desired height and release. The drone
will hover at that height.*
LANDING
1. Push down on the throttle until the drone is on the ground.
FIRST TIME FLYERS!!! TAKE YOUR TIME! GO SLOW!
Practice hovering until you are comfortable with ight before attempting
any other maneuvers. Make small movements letting the stick return to the
center. If you start to lose control, don’t panic. Just press land.
Pull the direction lever to the left or right,
the drone turns to the left or right.
NOTE:
- The engine will shut o if you choose to hold the throttle down for
3 seconds.
- EmergencyShutO:Wheninight,
pull the throttle and direction stick
to the center at the same time and
thedronewillshuto.
* The drone may drift a bit, especially in the rst 30 seconds until the
altitude sensor gets a good x on the position. Some drift is normal.
TIPS ON 360° FLIPS
Once you are familiar with the basics of drone ight, you can try some
advanced maneuvers! At a height of at least 10 feet, press and hold the
Flip Mode button and move the direction lever in any desired direction to
execute the ip.
Stunt Button
SPEED MODES
The Dronium Two AP features multiple speed modes. Choose the speed
based on ight experience and level of comfort. At higher speeds, the drone
will pitch more than at lower speeds. The Dronium Two AP is quite fast at its
highest speed and requires more piloting skills to y competently. For safety
take time to develop advanced skills by practicing at lower speeds rst. Press
the Speed Selector button to change the speed mode. The remote control
indicator will beep once at slowest speed mode and multiple times as speed
mode is increased.
Speed Button
14 15
* The drone will gain altitude as it goes into the ip.
Indice
Altri manuali Protocol Quadricottero
