Puch Mini maxi Manuale utente
OWNER'S
MANUAL
Dear
Puch Owner,
This
is
your riding, maintenance and warranty guide. By following
the
in-
structions described in this booklet, we
at
Puch know
you
will enjoymany
miles
of
pleasurable Moped Riding.
Should
a need ever exist
for
parts
or
service, simply
contact
your
Puch
dealer. He also
has
available for
your
purchase a Service Manual.
Thank
you
for
joining
the
Puch family, please ride safely and have fun.
Vehicle
Identification
Numbers
Carburetor
Choke,
Primer
Brakes
Brake
lever
Adjustment
Engine
stop
Switch
Fuel
Valve
Gas
Tank
Gas
Oil
Mixture
Head
light
Helmet
holder
Light
and
horn
switch
Starter
lever,
adjustment
Steering
lock
Transmission
fluid
Tire
pressure
Riding
Instructions
INDEX
General
Maintenance
and
Lubrication
Consumer
Information
Warranty
see
page
3
5
5
7
8
6
5
4
12
14
4
6
11
4
13
11
17
19
24
25
VEHICLE IDENTIFICATION NUMBERS
The vechicle identification number
(VIN)
is
located on the steering head
tube.
The frame identification number ist stamped into
the
steering head tube
above the vehicle identification number.
The
engine serial number
is
stamped on
top
of
the right engine case.
Important: Please checkthese numbers
at
the time
of
sale and compare
them whith your sales receipt
or
manufacture statement
of
origin.
3
Fig. 2 Fig. 1
4
Steering lock (Fig. 1
/1)
helmet holder (Fig. 1
/2)
To lock: Turn handlebar
to
the
right, insert key and push lock into
position
by
turning the keycounterclockwiseatthesametime.
The
lock
should stay in its position after turning
the
key
clockwise.
Pull
the
key off.
To unlock: Turn
lock
counter clockwise
to
free
front
fork.
Shouldyou decide
to
lockandsecureyourhelmetwithyourmoped,simply
place helmet strap into position (Fig. 1/2) before turning front
fork
to
the
right.
Gas tank (Fig. 2)
The gas tank
is
located underneath your seat.
To fill gasolinejust
tilt
seat forward
to
gain accesss
to
filler cap (Fig.
2)
and
storage compartment.
A
tool
set (Fig. 2/1) and measuring
cup
(Fig. 2/2) is included.
Fuel Valve (Fig. 3)
The fuel valve
is
positioned onthe
I.
h.
side
of
your seat bench.
Position 1 = closed
Position 2 = open
Po
sition 3 = reserve
Carburetor
(fig
.
4)
Ch
oke
(Fig. 4/1). Push down
to
ac
tuate it. The
choke
will be released au-
tomatically (see riding instructions).
Primer (Fig.4/2).The primer button has
to
beheld down in order
to
flood
the carburetor.
St
op
priming
as
soon
as
gas drips from carburetor.
Fig. 3 Fig. 4
5
Fig. 6 Fig. 5
6
Light and Horn Switch (Fig.
5)
The light and horn switch is located on
the
left hand side
of
the handlebar.
Position 1 = light
off
Position 2 = light on
Press button
to
actuate horn.
Engine stop switch (Fig.
6)
The engine stopswitch is
locat_ed
on the right hand side
of
thehandlebar.
To operate moped, the switch has
to
be
in
RUN
position.
Switch
to
OFF
in
order
to
turn
off
the
ignition, which stops the engine.
Brakes (Fig.
7)
The brake levers are mounted on both sides
of
the
handlebar.
The leftlever (Fig. 7/1) controls
the
rear wheel brake.
The right lever (Fig. 7/2) controls
the
front wheel brake.
Fig. 7
7
Fig. 9 Fig. 8
8
ADJUSTMENT
OF
BRAKES
Front Wheel Brake
The brake lever on
the
handlebar should have a play
of
app. 3/4" as
measured at
the
hand brake lever(Fig. 8). Theadjustmentis madewith
the
adjustment screw (Fig.
9/1)
(loosen counternuts!).
Rear Wheel Brake
The brake lever on
the
handlebar should have a play
of
app. 3
/4"
(see
Fig. 1
0).
Th
e adjustment is ra
de
with the ad
ju
stme
nt
screw (Fig. 11/1)
Fig.
10
Fig. 11
9
Altri manuali per Mini maxi
1
Indice
Altri manuali Puch Scooter
