Puck KEYSAFE Manuale utente
User and assembly manual 3
Gebruikers- en montagehandleiding 18
Bedienungs- und Montageanleitung 33
Manuel de l’utilisateur et installation 48
3
Manual for the installer and
end user
Dear customer,
Thank you for purchasing the Puck
Keysafe. This manual contains all the
information needed to quickly familiarize
yourself with the product. We kindly
request you to go through this information
carefully, before you start to work with the
product.
This manual is intended for installers and
end users of the Puck Keysafe. This is the
original manual. Keep these instructions
safe!
For more information, please contact your
local Puck Dealer, which you can find on:
www.puck-keysafe.com.
Puck Keysafe
user and assembly manual
Contents
1 Introduction 4
1.1 Intended use 4
1.2 Symbols used 4
2 Main components 5
2.1 Fixings 6
2.2 Operating elements 6
3 Mounting 7
3.1 Mounting the Puck Keysafe 7
on a brick or concrete wall
3.2 Mounting the Puck Keysafe 11
on a door frame
4 Use 14
4.1 Opening the Puck Keysafe 14
4.2 Setting the code 15
5 Maintenance, environment 17
and disposal
6 Guarantee 17
4
User and assembly manual
1 Introduction
With Puck Keysafe you can store your
keys safely where you need them. The
Puck Keysafe has been SKG approved and
graded as **. The Puck Keysafe can be
accessed by entering a four-digit code.
The Puck Keysafe has two safeguards to
keep your secret code from third parties:
1. The Puck Keysafe is equipped with an
anti-reading cap. This cap makes it
more difficult for third parties to look
over your shoulder as you enter your
PIN.
2. When you open the Puck Keysafe, the
code does not remain, but switches to
another number combination.
1.1 Intended use
The Puck Keysafe is a key safe, designed
for you to store your house keys safely in
the home. The Puck Keysafe can be
opened using a four-digit code. You set
this code yourself. Make sure you know
the code before closing the key cabinet of
the Puck Keysafe. Do not share your code
with third parties.
The Puck Keysafe can be mounted on a
stone or concrete wall, or on a door by
means of a mounting bracket.
1.2 Used symbols
The following four marking conventions
are used in this manual:
attention Attention! A note with
additional information to the user.
A note which alerts the user to potential
problems.
Puck Keysafe is certified
according to the assessment
directive SKG IKOB KE 470
with the classification of 2 stars. This
means that an unauthorised person needs
more than 3 minutes to break open the
safe.
5
2 Main components
Figure 1. Main components
1. Anti-read cap
2. Cover
3. Key cabinet
4. Mounting plate
5. Mounting bracket (optional)
21 3 4 5
6
User and assembly manual
2.1 Fixings
Figure 2. Safe fixing
Figure 3. Fixing mounting bracket
1. Hexagon bolt M8 x 40 mm (3x)
2. Wall Anchor (3x)
3. Hex nut M6 (3x) (optional)
4. Wood screw (4.5 x 30 mm) (optional)
5. Coach bolt M6 x 25 mm (3x) (optional)
2.2 Operating elements
Figure 4. Operating elements
1. Figure Wheels
2. Code setting slider
1 2
1
2
4 53
7
3 Mounting
The Puck Keysafe can be mounted in two
ways:
1. Mounting on a brick or concrete wall.
2. Mounted on the frame of a door.
3.1 Mounting the Puck Keysafe on a
brick or concrete wall
attention
• Mounting should preferably be
performed by a qualified installer.
• The wall where the safe is to be
mounted must be flush.
• The wall must be made of brick or
concrete.
To mount the Puck Keysafe on a wall, do
the following:
1. Open the Puck Keysafe. The code is
factory preset to 0000.
• Using the number wheels enter the
code '0000'.
• Turn the lid anti-clockwise and then
pull it toward you.
2. Determine where you want to mount
the Puck Keysafe. The height must be
120-150 cm.
3. Keep the mounting place to the desired
location so that two holes are facing up
and one hole is facing down.
Figure 5. Position the Puck Keysafe
120-150 cm
8
User and assembly manual
4. Mark the holes.
Figure 6. Mark the holes
attention
The holes cannot be drilled into the joints.
5. Drill three 12 mm holes 85 mm deep.
Figure 7. Drill the holes
6. Insert the wall anchors.
Figure 8. Insert the wall anchors
9
7. Activate the wall anchors by turning them with a hexagonal spanner.
Remember that when tightening the wall anchors will be pulled a few millimetres into
the wall.
Figure 9. Activate the wall anchors
8. Mount the key cabinet on the wall with the hexagonal bolts. Tighten the bolts by hand.
Figure 10. Mount the key cabinet on the wall
10
User and assembly manual
9. Change the code. For more information see paragraph 4.2.
10. Place the cover. This is done by firstly sliding it over the key cabinet and then
turning it. You will hear a click.
Figure 11. Place the cover
Well done! You have completed the mounting.
Indice
Lingue:
