Pullman Holt Gloss Boss GB-1500X Guida all'installazione

Save For Future Reference

WARNING

RISK OF FIRE. Do not use with a flammable

or combustible liquid to clean a floor.

“Gloss Boss” Burnisher GB-1500X

Operation & Care Instructions

This 1500-RPM burnisher is a high quality, precision made product. All parts used in the

manufacturing of this burnisher have passed rigid quality control standards prior to assembly,

and an "each unit" final inspection prior to packaging is your assurance of proper assembly.

This burnisher was protectively packed to prevent possible damage in transit. Should damage

occur,please notify the transporting carrier immediately for loss and/or claim.

IMPORTANT SAFEGUARDS

GROUNDING:

This burnisher must be grounded while in use to protect the

operator from electric shock. The burnisher is equipped with

an approved three-conductor cord and three-prong grounding

type plug to fit the proper grounding type receptacle. The

green (or green and yellow) conductor in the cord is the

groundingwire. Neverconnectthegreen(orgreenandyellow)

wire to a live terminal.

If your unit is for use on less than 150

volts, it has a plug like that shown in

Figure A.

If it is for use on 150 to 250 volts, it has a

plug like that shown in Figure D.

An adapter (Figures B&C) is available for connecting Figure A

plugs to two-prong receptacles. The green-colored rigid ear,

lug etc., must be connected to a permanent ground such as a

properly grounded outlet box. No adapter is available for a

plug as shown in Figure D. Adapter shown in Figure B & C is

not for use in Canada.

MOTOR:

This burnisher is powered by a 1-1/2 HP AC motor. Be sure

your power supply agrees with the voltage marked on the

name plates. A voltage decrease of more than 10% will cause

the motor to slow down, thus increasing the current draw and

opening the circuit breaker.

EXTENSION CORDS:

Burnishers that have 3 wire cords requiring grounding must

only be used with extension cords that have 3-prong

grounding type plugs and 3-pole receptacles.

To determine the minimum wire size required, refer to the

chart below:

Minimum Wire Size (AWG) of Extension Cord

Nameplate Total Extension Cord Length (Feet)

Rating-Amps 25 50 75 100 125 150 175 200

0-10.0 18 18 16 16 14 14 12 12

10.1-13.0 16 16 14 14 14 12 12 12

13.1-15.0 12 12 12 12 12 12 12 –

Before using an extension cord,inspect it for loose or exposed

wires, damaged insulation and defective fitting.

CAUTION

Always disconnect power cable from outlet

when working on this burnisher.

ABOUT THE MACHINE

TO ADJUST HANDLE:

This burnisher is packaged with the handle folded forward and

the foot pedal in the up position.

1. Depress the foot pedal then raise the handle until the open-

ing in the bottom of the handle is centered over the handle

lock.

2. Return the foot pedal to the up position, which allows the

centerlock to position inside the handle. The handle is now

LOCKED for travel.

3. When ready to operate, depress the foot pedal,then lock by

pushing forward. The handle is now FREE FLOATING.

Note: The handle on this burnisher MUST BE FREE FLOATING

to permit proper operation.

TO ATTACH PAD:

1. With handle locked in the upright position, tilt burnisher

back on the handle until the underside is fully exposed.

2. Remove the plastic pad lock by turning clockwise.

3. Install pad.

4. Lock center device by turning counter-clockwise.

NOTE: Never Operate the Burnisher without a pad.

TO START:

The normal position of this burnisher, with the pad stationary,

is tilted back on the four wheels with the pad off the floor.

1. Remove cable completely from cable hooks.

2. With the handle in free float position and the power cable

plugged into the proper outlet, squeeze the switch bar

beneath the handle grips.

3. As the motor reaches full speed (1-2 seconds),the pad will

slowly fall to the floor due to the partial vacuum between

the pad and the floor created by the high speed pad rota-

tion.

TO OPERATE:

For best result,use a clean pad and change frequently as pad

loads up. A motor overload could result from a dirty, loaded

pad. If the built-in circuit breaker trips, wait five (5) seconds,

then depress button on the side of the switchbox. Change the

pad.

Operate the burnisher in a straight-line path. Avoid continuous

operation inonespot,assuchoperationmaydamage thefloor.

CARE AND MAINTENANCE:

Thisburnisher will afford you may years of trouble-freeservice

provided it is given proper care. Throwing, dropping bumping

across the thresholds and other misuse may result in a

damaged unit and invalidate the warranty. When storing your

burnisher, always remove the pad. Pads can be cleaned by

washing in warm water with mild detergent,rinsing,and hung

up to dry.

Itis not necessarytolubricate this burnisher. Allbearingshave

been pre-lubricated and permanently sealed at the factory.

10702 N 46th Street •Tampa, FL 33617

(813)971-2223 •toll free (800) 237-7582

fax (813) 971-6090 •order entry fax (800) 833-8875

www.pullmanholtcorp. com B703523 1/04

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Pullman Holt Macchina per pavimenti

Pullman Holt

Pullman Holt StoneCare B16F-SC-AT Manuale utente

Pullman Holt

Pullman Holt B16F-HW Manuale utente

Pullman Holt

Pullman Holt Gloss Boss GB-2000DC Guida all'installazione

Pullman Holt

Pullman Holt Gloss Boss GB-1500F Guida all'applicazione

Pullman Holt

Pullman Holt B13B Manuale utente

Pullman Holt

Pullman Holt ES2000 Manuale utente

Pullman Holt

Pullman Holt Gloss Boss GB-1500 Manuale utente

Pullman Holt

Pullman Holt Gloss Boss GB-2000DC Manuale utente

Pullman Holt

Pullman Holt ES2000 Guida all'installazione

Pullman Holt

Pullman Holt DS-20 Guida all'applicazione

Pullman Holt

Pullman Holt SC400 Guida all'installazione

Pullman Holt

Pullman Holt B13B Guida all'applicazione

Pullman Holt

Pullman Holt ES2000 Guida all'applicazione

Pullman Holt

Pullman Holt DS-20F Manuale utente

Pullman Holt

Pullman Holt SC400 Manuale utente

Pullman Holt

Pullman Holt B13E Guida all'applicazione

Pullman Holt

Pullman Holt DS-20 Guida all'installazione

Pullman Holt

Pullman Holt Gloss Boss GB-1500F Guida all'installazione

Pullman Holt

Pullman Holt Floor Machine Guida all'installazione

Pullman Holt

Pullman Holt GB-1090 Manuale utente

Pullman Holt

Pullman Holt Gloss Boss GB-1090F Guida all'applicazione

Pullman Holt

Pullman Holt B16F-HW Guida all'installazione

Pullman Holt

Pullman Holt Gloss Boss GB-1090F Guida all'installazione

Pullman Holt

Pullman Holt Gloss Boss GB-1500X Guida all'applicazione

Manuali Macchina per pavimenti popolari di altre marche

Nilfisk-Advance

Nilfisk-Advance Advance SC370 17B Manuale utente

Numatic

Numatic ET 4045 Manuale utente

HAWK ENTERPRISES

HAWK ENTERPRISES HP1513-180BRUTE Manuale utente

Mytee

Mytee 8070 Mytee-Lite Manuale utente

Kärcher

Kärcher B 140 R Manuale utente

Triple S

Triple S Ace 26T1 Manuale utente

Nilfisk-Advance

Nilfisk-Advance SW 750 Manuale utente

Tornado

Tornado Marathon 2000 98190 Manuale

Windsor

Windsor ADMIRAL Admiral 8 Manuale utente

Numatic

Numatic TTB 1117/100 Manuale utente

Tennant

Tennant 8210D Manuale utente

Nobles

Nobles Frontier Manuale del prodotto

lavina

lavina 21-X Manuale utente

KENT

KENT Edge 28B Manuale utente

Tennant

Tennant 215 Manuale del prodotto

Windsor

Windsor BDP 51/2000C Manuale utente

CleanFreak

CleanFreak DURA-18HD Manuale utente

Nilfisk-Advance

Nilfisk-Advance Warrior 34RST Guida per l'amministratore