Puretec D Series Manuale utente
For correct operation & installation it is essential to observe these instructions.
DEC2019
WMTS105:2016
Certicate No. 23291
Australian Certication
Services
User Guide
Freestanding Water Chiller System
D Series
2Installation & Operation Manual Copyright © Puretec Pty Ltd 2019
What's Inside
Product Information
Distributor:
Installer:
Phone:
Date Installed:
What's Inside
Puretec Customer Service ................................................................................................. 3
Introduction................................................................................................................................. 3
Cartridge Replacement ......................................................................................................... 3
Parts Diagram............................................................................................................................ 4
Installation Requirements................................................................................................... 5
Installation................................................................................................................................... 6
Operation & Maitenance...................................................................................................... 7
Cartridge Changout................................................................................................................. 7
Use Guidelines........................................................................................................................... 8
Electrical Diagram................................................................................................................... 8
External Filter Installation................................................................................................... 9
Troubleshooting ..................................................................................................................... 10
Performance Data ................................................................................................................ 10
Warranty .................................................................................................................................... 11
3
D SERIES | Freestanding Water Chiller System
Puretec Customer Service
Thank you for purchasing a Puretec Freestanding Water Chiller System. Your system is
a proven performer manufactured from only quality materials and components and will
give years of spring-like water, if maintained properly.
The Puretec lter supplied with the Freestanding Water Chiller System needs regular
cartridge replacement to maintain optimum performance. This is a simple procedure
when following instructions. For cartridge replacements contact your nearest Puretec
stockist.
Customer Service Helpline 1300 140 140 (Australia) 0800 130 140 (New Zealand).
Introduction
The Puretec Freestanding Water Chiller System is designed to run economically for many
years, dependent on the initial installation and periodical maintenance.
Flush systems for 10 minutes aer any period of non-use more than 2 days.
The Freestanding Water Chiller System is designed to operate with mains water.
Installation Note: A water lter system/tap, like any product, has a limited life and may
eventually fail. Also sometimes failure happens early due to unforeseen circumstances.
To avoid possible property damage, this product should be regularly examined for
leakage and/or deterioration and replaced when necessary. A drain pan, plumbed to an
appropriate drain or outtted with a leak detector, should be used in those applications
where any leakage could cause property damage, and/or the water supply should be
turned o if no one is home/present.
Cartridge Replacement
To maintain the high quality of the puried water the cartridges need changing every
6 - 12 months, dependent on water quality and usage. You can obtain replacement
cartridges from your local Puretec dealer. To maintain performance standards and
warranty, use only genuine Puretec replacements.
Replacement cartridge code for D Series model: Z1-R
Puretec Customer Service
4Installation & Operation Manual Copyright © Puretec Pty Ltd 2019
Parts Diagram
Fig. 1 Parts Diagram
Main Shell
Power Cord
Flexible Drain
Pipe
Top Panel
Bubbler Tap
Carafe Filler
(specied
models only)
Cold Water Tank
with Insulation
Z1 Filter
Cartridge*
Waste
Trap
Front Panel
Bubbler Tap Push-t
Connector
Carafe Filler Push-t
Connector
Fan
Drain Plug
Power Cable
Terminal
Condenser
Compressor
Terminal
Box
Cold Water
Thermostat
* Only D10I, D10IC, D20I, D20IC, D30I & D30IC Models have Z1 Filter installed internally on bubbler.
5
D SERIES | Freestanding Water Chiller System
Installation Requirements
Installation Requirements
The following is a guide but the installer is responsible to comply with any local
regulations that may be applicable to this type of installation.
1. Install near a convenient place to connect to a mains pressure water supply of
drinking water quality and 220 - 240V/50Hz electrical supply.
2. Avoid areas exposed to excessive heat, humidity, rain, saltwater or snow or direct
contact with water spray or splashing.
3. Avoid positions of direct sunlight or solar heat.
4. Install only on at, level and well supported surfaces.
5. Avoid tilting the machine during installation. If the machine has been tilted
excessively for more than a few minutes during or before installation, leave to
stand for approximately one hour before switching on.
6. Allow an air gap of at 100 mm each side and at the front of the machine.
1080
865
300
Installation option when the filter
installed externally
Min. 300mm from the ground level
Flexible Drain Pipe:
Outside Diameter: ø 40mm
Min/Max Length: 300 - 830mm
Note: A rubber flexible connector is
recommended to connect hose to drain.
Connected to the mains water
supply
Fig. 2 Installation Diagram
6Installation & Operation Manual Copyright © Puretec Pty Ltd 2019
Installation
Installation
1. Once positioned and levelled remove the front panel
2. Assemble the carafe ller by inserting the gooseneck outlet into the carafe ller
base that comes installed on the sink. Ensure the gooseneck outlet is pushed in
hard until properly sealed.
3. An access port for the drain is provided at the rear of the cabinet and there is a
closed rubber grommet pre-tted which can be cut or opened to access the drain
connection
4. Unscrew the compression nut from the waste trap outlet and place the rubber seal
and the compression nut over the end of the exible drain line. Insert the exible
drain line into the waste trap outlet and tighten the compression tting for a tight
waterproof seal.
5. Connect the inlet water supply to the ¼” tube tting at the rear of the cabinet and
ensure there is an easily accessible shuto valve on the water supply line. Fit a
pressure reducing valve to regulate the water pressure if required - max 520 kPa.
6. Switch on the water and check all tubing and ttings for water leaks.
7. Open the quarter turn spindle on the carafe ller until water dispenses and then run
the water for 1 minute to clear air pockets and ush the lter.
8. All Puretec freestanding chillers are supplied with a Puretec lter to ensure water
of the highest quality. I models have the lter pre-installed internally. E models are
supplied with the lter seprately and will need to be installed (see External Filter
Installation on page 9).
9. When new it may take up to 1 minute to ll the system prior to dispensing water
10. Connect the power cord to a standard 240V powerpoint and switch on the electrical
supply.
11. Ret the front panel.
12. Allow 1 hour for the water to cool before the water reaches its operational
temperature.
13. To protect the compressor, allow the unit to stand for at least 1 hour aer moving
before switching it back on.
7
D SERIES | Freestanding Water Chiller System
Operation & Maintenance
Operation & Maintenance
• Frequently clean the fountain using warm soapy water. Avoid all abrasive and corrosive
cleaning materials.
• Do not pour any waste cleaning water down the drain to avoid blocking the drain trap.
• If the chiller is not used (e.g. more than 3 days) the power can be switched o to
conserve energy.
• We recommend that the fountain is cleaned aer any period of disuse.
• It will be necessary to change the lter aer an extended period of disuse (e.g. more
than 2 weeks).
• Keep the area surrounding the fountain clean and dry. In the event of any leakages,
switch o the water and power and call Puretec.
Cartridge Changeout
Replacement cartridge code for D Series systems: Z1-R
1. Turn o the water supply at an external shut o valve.
2. Remove all packaging from the new cartridge, including any wraps or caps (if
applicable).
3. Rotate the old cartridge counter-clockwise 1/4 turn, pull it out and dispose of it.
4. Insert the new cartridge into the lter head and rotate clockwise 1/4 turn.
5. Turn on the water supply and check for leaks.
6. If leaks occur, repeat step 2 & 3.
7. If leaks persist discontinue use and call Puretec.
8. Open the quarter turn spindle on the carafe ller until water dispenses and then run
the water for 1 minute to clear air pockets and ush the lter.
8Installation & Operation Manual Copyright © Puretec Pty Ltd 2019
Use Guidelines
Use Guidelines
• Use for mains water supply.
• Minimum operating pressure 200 kPa.
• Maximum operating pressure 520 kPa.
• Do not allow exposure to temperatures below 0 °C, protect from freezing.
• Maximum operating temperature 38 °C.
• Nominal ow rate 5.5 Lpm.
• System must be installed according to local plumbing codes on the cold water line only.
• This system requires regular replacement of the lter cartridge to maintain proper
operation. Varying chlorine, sediment, or organic substance levels may aect
• replacement frequency.
• Be sure to change the lter cartridge every 6 - 12 months or whenever you detect a
change in taste, odour, or decrease in ow.
Caution: Do not use with water that is microbiologically unsafe or of unknown quality
without adequate disinfection before the chiller.
Cold Thermostat
Compressor
Fan
Fuse
Fig. 3 Electrical Diagram
9
D SERIES | Freestanding Water Chiller System
External Filter Installation
1. Select suitable location that is close to the Freestanding Water Chiller System.
Remember to allow access room for changing lters and a suitable place where
water spillage will not cause damage. Location should not be in direct sunlight.
2. Isolate water supply. Uninstall the connections on the cold water line and connect
the tubing, a Smart Tee™ (sold separately) is recommended. Reinstall the previous
connection to the tee valve.
3. Connect a pressure limiting MultiValve (sold separately) to the tee valve with a
length of White Tubing.
6. Install lter cartridge by positioning it in the desired location, marking the
position of xing hole and xing with bracket screw. The Z1 lter can be mounted
horizontally or vertically. Allow room for the connecting tubes. Ensure ow arrow
on the head is in direction of the water ow.
7. Fit tubing into connectors. Allow slack in the tubing.
8. Restore the water supply and check for leaks.
9. When new it may take up to 1 minute to ll the system prior to dispensing water.
Run the system for at least 5 minutes to remove carbon nes. Water may appear
milky, but this is normal and is only tiny air bubbles that will clear aer a short
period.
Fig. 4 External Filter Inlallation Diagram
External Filter Installation
Chiller
Cold Water
Supply
Tee Valve
(sold separately)
MultiValve
(sold separately)
Z1-R Filter Cartridge
Filter Head
& Bracket
Tubing
10 Installation & Operation Manual Copyright © Puretec Pty Ltd 2019
Troubleshooting Guide
Troubleshooting Guide
In the event of any other breakdown, please call Puretec
Fault Possible Cause Suggested Action
Not cooling. The compressor is not running. Check the power is switched on.
The power is on but not cooling. The thermostat is set too high. Reduce the thermostat
temperature setting.
Water leakage. The pipes or connections are
leaking.
Switch o power, turn o water
and call your service engineer.
Slow water ow. The lter is blocked. Change the lter.
No water dispenses from the
taps.
Water inlet valve(s) closed or
other blockage.
Open and/or reset the water
inlet valve(s) and check water
supply pipe
Drainage waste blocked. Debris has blocked up the
waste system. Clear the obstruction.
Performance Data
Model Function Voltage Frequency
Max
Cooling
Power
Cooling
Capacity
Refrigerant
Type
Refrigerant
Charge
D10E
D10EC
D10I
D10IC
Cooling 220 - 240 50 Hz 85 W 10 Lph R134a 110g
D20E
D20EC
D20I
D20IC
Cooling 220 - 240 50 Hz 120 W 20 Lph R134a 160g
D30E
D30EC
D30I
D30IC
Cooling 220 - 240 50 Hz 200 W 30 Lph R134a 180g
Questo manuale è adatto per i seguenti modelli
12
Indice
Altri manuali Puretec Refrigeratore
