PV-ezRack PostMount 6-A Manuale tecnico

PostMount 6-A for XL Panels

Code-Compliant Planning and Installation Guide V 2.0

Complying with AS/NZS 1170.2: 2021

Last Updated - Mar. 2023

Installation Guide / PostMount 6-A for XL Panels

1Code-Compliant Planning and Installation Guide V 2.0 - Complying with AS/NZS1170.2-2021

Introduction

Complying with all applicable local or national

building codes, including any updates that may

supersede this manual;

Ensuring that PVezRack® and other products are

appropriate for the particular installation and the

installation environment;

Using only PVezRack® parts and installer supplied

parts as specified by PVezRack® project plan

(substitution of parts may void the warranty and

invalidate the letter of certiﬁcation);

Recycling: according to the local relative statute;

Ensuring that there are no less than two professionals

working on panel installation;

Ensuring the installation of related electrical

equipment is performed by licenced electricians;

Ensuring safe installation of all electrical aspects of

the PV array, including providing adequate earth

bonding of the PV array and PVezRack® PostMount

components as required in AS/NZS 5033: 2021.

•

The installer is solely responsible for:

Clenergy PVezRack® PostMount 6-A for XL Panels (up to

2100 x 1100 mm) is a ground mounting system suitable

for large scale commercial and utility scale installations.

PVezRack ® PostMount 6-A for XL Panels has been

developed to fit any PV module in the outdoors and

uneven ground areas. PVezRack ® PostMount 6-A for XL

Panels have good compatibility for the different region

via the angle adjustment (10°~ 60°). Using high quality

engineered components PostMount 6-A for XL Panels

saves developers and installers, time and money when

delivering large scale projects.

Please review this manual thoroughly before installing

PostMount 6-A for XL Panels. This manual provides the

following contents:

1) Installation planning;

2) Installation instructions.

- Introduction -

The PVezRack® PostMount 6-A for XL Panels parts,

when installed in accordance with this guide, will be

structurally adequate and meet the AS/NZS 1170.2:

2021 standard. During installation, and especially

when working on the ground, please comply with the

appropriate occupational health and safety regulations.

Please also pay attention to other relevant regulations

in your local region. Please check that you are using the

latest version of the installation manual by contacting

Clenergy via email on www.clenergy. com.au or

contacting your local distributor.

Product Warranty:

Please refer PVezRack® Product Warranty on our

website.

List of contents

Introduction

Tools & Components

System Overview

Installation Instruction

Certiﬁcation

03 - 05

06 - 11

12 - 16

Installation Guide / PostMount 6-A for XL Panels

Code-Compliant Planning and Installation Guide V 2.0 - Complying with AS/NZS1170.2-2021

- Tools and Components -

Tools and Components

Tools

Allen Key

6 mm

String & Marker Pen

Spanner

Anchoring Kit

Torque

Wrench

Mixing Nozzles

Tape

Components

C-U/30/46-G

Universal Clamp x 4

ER-R-ECO/XXXX

ECO-Rail x 6

ER-AP-PM6/8/A-LP

PM6-A, PM8-A

Kit x 1

ER-RT-100/2200

PM6-A Rectangular

Tube-Master x 1

ER-RT-70/3170

PM6-A&PM8-A

Rectangular Tube-

Landscape x 3

ER-P-152/3000

Pipe x 1

ER-SC-PM6

PM6-A, PM8-A Steel Cap

Assembly x 1

ER-RT-100/576

PM6-A, PM8-A Steel Cap

Assembly x 1

EZ-GL-ST/UC

Grounding Lug x 4

ER-I-05/CM

Tin Interface

with Click Module

Installation Guide / PostMount 6-A for XL Panels

3Code-Compliant Planning and Installation Guide V 2.0 - Complying with AS/NZS1170.2-2021 - System Overview -

System Overview

Overview of PVezRack® PostMount 6-A for XL Panels

Side view drawing of PVezRack® PostMount 6-A for XL Panels is shown below. The panels tilt angle and embedment

depth below are for reference only. Please refer to Certiﬁcate Letter to obatin the certiﬁed max panels tilt angle and

min embedment depth for different wind regions and different soil types.

1.Universal Clamp 2. ECO-Rail 3. PM6-A Rectangular Tube- Landscape 4. PM6-A Rectangular Tube-Master

5. Steel Cap Assembly 6. PM6-A Adjustable Tube 7. Pipe 8. PM6-A Kit

Installation Guide / PostMount 6-A for XL Panels

Code-Compliant Planning and Installation Guide V 2.0 - Complying with AS/NZS1170.2-2021

- System Overview -

Precautionary Measures for Stainless-Steel Fastener Installation

Improper operation may lead to the deadlock of bolts and nuts. Follow the steps below to reduce this risk.

Reduce the friction coefﬁcient

(1) Ensure that the thread surface is clean (no dirt or contaminant).

(2) Apply lubricant (grease or 40# engine oil) to fasteners prior to tightening to avoid galling or seizing in the threads.

Precautionary Measures for Stainless-Steel Fastener

Installation

Installation Guide / PostMount 6-A for XL Panels

5Code-Compliant Planning and Installation Guide V 2.0 - Complying with AS/NZS1170.2-2021 - System Overview -

General installation instructions

(1) Apply force to fasteners in the direction of thread.

(2) Apply force uniformly to maintain required torque.

(3) Professional tools and tool belts are recommended.

(4) Avoid using electric tools for ﬁnal tightening.

(5) Avoid working at high temperatures.

Safe Torques

Please refer to safe torques deﬁned in this guide as shown in the ﬁgure below. If power tools are required, Clenergy

recommends the use of low speed only. High speed and impact drivers increase the risk of bolt galling (deadlock). If

deadlock occurs and you need to cut fasteners, please make sure that there is no load on the fastener before you cut it.

Avoid damaging the anodized or galvanized surfaces.

Installation Dimensions

All drawings and dimensions in this installation guide are for generic reference. The PVezRack® PostMount 6-A for XL

Panels is to be optimized to suit specific conditions for each project and documented in engineering drawings. As

a result, major components of the PVezRack® PostMount 6-A for XL Panels may be provided in sectional sizes and

lengths that vary from those shown in this guide. The installation operations detailed in this instruction guide remain

the same regardless of the component size. In case you need to do any on-site modifications or alteration of the

system in a way that would be different from engineering drawings, please provide marked up drawings/sketches for

Clenergy’s review prior to modiﬁcation for comment and approval.

Installation Guide / PostMount 6-A for XL Panels

Code-Compliant Planning and Installation Guide V 2.0 - Complying with AS/NZS1170.2-2021

- Installation Instruction -

Installation Instruction

Dig a hole with the diameter of 300mm .

Place the pole into the middle of the hole and ﬁll it with

concrete (min 25 MPa strength). Maintain the position of

the post. The allowed vertical tolerance is ±2°. Keep the

axle of the 2- Ø22 holes parallel to East-West; keep the

vertical angle deviation within ±5°. For more than one

system on one site maintain all the axles of 2- Ø22 holes

aligned.

Connect the Pipe to the corrugated washer and Steel Cap Assembly with M20*210 hexagonal bolt, spring washer 20,

M20 nut.

Combine two Steel Caps with M20*160 hexagonal bolt, spring washer 20, M20 hex nut.

Notes:

1) Do not fasten the Bolt prior to complete the assembly of PM-A Rectangular Tube-Master.

2) Keep all the Bolt head aligned.

Pipe Installation

Steel Cap Installation

Installation Guide / PostMount 6-A for XL Panels

7Code-Compliant Planning and Installation Guide V 2.0 - Complying with AS/NZS1170.2-2021 - Installation Instruction -

Notes:

1) Adjust the angle of the allation, the angle of the Rectangular

Tube-Master with 10°(6 holes from up to bottom corresponds

to 10° to 60° tilt angle) in order to make the assembly process

run smooth.

2) Using adjustable washers to fill gaps between the

Rectangular Tube-Master and the Adjustable Tube and Steel

Cap. Image on the right shows adjustable washers inserting

between the Rectangular Tube-Master and Steel Cap.

Fix the Rectangular Tube-Master at Steel Cap Assembly

with M20*160 hex bolt, M20 nut, plain washer 20, and spring

washer 20. See the mark (1).

Fix the Adjustable Tube at Rectangular Tube-Master with

M20*160 hex bolt, plain washer 20, and spring washer 20,

M20 nut. See the mark (2).

Fix the Adjustable Tube at Steel Cap Assembly with M20*160

hex bolt, M20 nut, plain washer 20, and spring washer 20. See

the mark (3).

Realized the angle adjustment by position the bolt in the

differrent holes.

Fasten the Steel Cap Assembly to Pipe with M20*210,

M20*160 Hex Bolt, keep the Rectangular Tube-Master parallel

to the south-north by adjust the

Steel Cap Assembly

Recommended torque for M20 bolts is 210~220 N·m.

PM6-A Rectangular Tube-Master Installation

Installation Guide / PostMount 6-A for XL Panels

Code-Compliant Planning and Installation Guide V 2.0 - Complying with AS/NZS1170.2-2021

- Installation Instruction -

Fix the 3 pcs PM6-A Rectangular Tube-Landscapes at Rectangular Tube-Master on pre-welded L proﬁle angle bracket

with 2 pcs M12*100 hex bolts, 2 pcs M12 nuts , 2 pcs plain washers 12 and 2 pcs spring washers 12. Do not fasten the

Nut until 3 Rectangular Tube-Landscapes aligned.

Recommended torque for M10 bolts is 35~40 N·m.

Fix the ECO-Rail to Rectangular Tube-Master with M8*20 hex socket bolt, Z module, Spring washer 8, Washer 8.

Note:

Make sure that the rail ends align horizontally and that the rails are parallel to each other.

Recommended torque for M8 bolts is 18~20 N·m

Rectangular Tube- Landscape Installation

ECO-Rail Installation

Installation Guide / PostMount 6-A for XL Panels

9Code-Compliant Planning and Installation Guide V 2.0 - Complying with AS/NZS1170.2-2021

Apply one pre-assembled Grounding Lug per Rail. Click the Grounding Lug into to the rail channel and insert the

Copper Wire. (the maximum size is 10 mm2) Fasten the bolt M6*14 with 5~6 N.m and the bolt M8*25 with 16~20 N.m.

End Clamp Inter Clamp

- Installation Instruction -

PV Module Installation

Fix the PV panel to Rail, via Universal Inter Clamps and

End Clamps step by step until all the panels complete.

Recommended torque for M8 bolts is 18~20 N·m

Note:

The Universal Clamp can be used both as a End Clamp

and a Inter Clamp, and the height can be adjusted from

30 to 46 mm.

When the side of the Universal Clamp close the narrow

side of the Universal Clamp Buckle, it can be used as

End Clamp, and when the side of the Universal Clamp

close the wide side of the Universal Clamp Buckle, it can

be used as Inter Clamp, as shown in the figure on the

right. The Universal Clamp can be directly rotated to the

position of required End or Inter Clamp.

Recommended torque for M8 bolts when it is Inter Clamp

is 18~20 N·m

Recommended torque for M8 bolts when it is End Clamp

is 13~14 N·m

Altri manuali PV-ezRack Rack e supporto

PV-ezRack

PV-ezRack PostMount 8-A Manuale tecnico

Manuali Rack e supporto popolari di altre marche

Salamander

Salamander Acadia AC/W/L400/WH Manuale utente

Fohhn

Fohhn VAT-09 Guida utente

ricoo

ricoo FS0522 Manuale utente

AMSOIL

AMSOIL BMK-22 Guida rapida

Kargo Master

Kargo Master 48220 Manuale utente

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuale utente

ricoo

ricoo S1222 Manuale utente

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuale utente

VidaBox

VidaBox VB MNT FFS2 Manuale utente

Welch Allyn

Welch Allyn 48960 Manuale utente

Arkon

Arkon CM035-ST-2 Manuale utente

PROEL

PROEL PLWIN60C Manuale utente

Agilent Technologies

Agilent Technologies E2609B Manuale utente

Mustang

Mustang MV-ARM4 Manuale utente

Mounting Solutions

Mounting Solutions WRM-320 Manuale utente

Pyle

Pyle PMKSPAD1 Manuale utente

ShelterIt

ShelterIt 21208 Manuale utente

SPL

SPL RackPack?4 1040 Manuale utente