Pvelectronics Spectrum 1040 Guida rapida

Stainless Steel Case - Spectrum 18 / 1040

Issue 1 (20 July 2016)

www.pvelectronics.co.uk

Assembly N tes

Stainless Steel Case

F r Nixie Cl ck

Type Spectrum 18 / 1040

Stainless Steel Case - Spectrum 18 / 1040

Issue 1 (20 July 2016)

www.pvelectronics.co.uk

REVISION HISTORY

Issue

Number

Date Reas n f r Issue

1 20 July 2016 New document

1. APPLICABILITY

This case is suitable for the following versions of the Spectrum

Ni ie clock:

Spectrum 18: PCB date 1 October 2015, Assembled according

to Issue 6 instructions

Spectrum 1040: PCB date 5 November 2015, Assembled

according to Issue 6 instructions

Stainless Steel Case - Spectrum 18 / 1040

Issue 1 (20 July 2016)

www.pvelectronics.co.uk

2. PACK CONTENTS

Stainless Steel Case - Spectrum 18 / 1040

Issue 1 (20 July 2016)

www.pvelectronics.co.uk

3. ASSEMBLY GUIDE

3.1 Prepare the PCB

D4, D6 (5mm Yell w LED)

D5 (5mm Green LED)

LEDs D4, D5 and D6 need to be mounted as shown below (your

PCB may look a little different, but note the bending of the LED

leads). The originally longer lead goes to the pad marked +.

Place a self adhesive rubber foot on the base of the HV module as

shown, to prevent any possibility of contact with the metal case

3.2 Prepare the Case

Carefully remove all protective film from the stainless steel case

components. Peel from one corner.

Stainless Steel Case - Spectrum 18 / 1040

Issue 1 (20 July 2016)

www.pvelectronics.co.uk

3.3 M unt the PCB spacers n the PCB

Mount the components onto the PCB as shown below. Do this for

all si PCB mounting holes.

3.4 Prepare the DS18B20 Temperature Sens r

Separate the 3 way cable as shown and part the 3 leads of the

DS18B20 a little. Also cut 3 small pieces of clear heat shrink

insulation about 10mm long.

Strip 2mm of the insulation from the end of each of the 3 wires,

and tin the e posed copper with solder. Then slip the heat shrink

pieces over as shown below:

Stainless Steel Case - Spectrum 18 / 1040

Issue 1 (20 July 2016)

www.pvelectronics.co.uk

Then solder onto the DS18B20, slip the heat shrink over the

e posed joints and shrink with a heat gun:

Finally, strip the insulation from the other end and solder to the

PCB. Take great care to ensure the IC has the correct orientation

with respect to the PCB markings. There is no need to feed the

wires into the PCB holes, you can just lay the wires over the pads

and solder in place:

Stainless Steel Case - Spectrum 18 / 1040

Issue 1 (20 July 2016)

www.pvelectronics.co.uk

3.5 Apply rear legend

Remove the film from the adhesive side and attach the legend as

shown. At the end of the case assembly, also remove the front film

from the legend.

3.6 Feed the DS18B20 sens r thr ugh

From the inside of the case, feed the DS18B20 sensor through the

5mm rear hole which does not have a legend close to it.

3.7 Place PCB in case

Start by feeding both neons into their holes in the top part of the

case. Then you can tilt the PCB forwards so that the front he

spaces clear the case. Push forwards, and then tilt the PCB back

again and the rear he spacers will clear the case.

At this point, the PCB will be loosely in the case top part.

It is now necessary to work the 3 LEDs into their respective holes.

Temporarily secure the PCB in the correct position by using 4 of the

6mm screws to attach the 20mm he spacers to the top case part.

Stainless Steel Case - Spectrum 18 / 1040

Issue 1 (20 July 2016)

www.pvelectronics.co.uk

When the LEDs are in their holes, you can remove the screws but

do not allow the PCB to move with respect to the case, or the LEDs

will come out of their holes. If you grip the assembly as shown

below, you can keep the PCB in the correct position whilst you

remove the screws and move to the ne t step:

3.8 Place base c mp nent

Keeping the PCB in position, place the base component, and then

secure using the si M3 6mm screws. Do not overtighten the

screws. Place the 4 rubber feet at the corners of the underside of

the case.

3.9 Final assembly

Install the tubes into their sockets, remove the film from the rear

legend and finally place the glass neon covers over the AM / PM

neon indicators.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Pvelectronics Orologio

Pvelectronics

Pvelectronics Frank 3 Guida alla configurazione

Pvelectronics

Pvelectronics Dink Guida alla configurazione

Pvelectronics

Pvelectronics Nixie QTC Plus Guida alla configurazione

Pvelectronics

Pvelectronics Nixie QTC-Four Guida alla configurazione

Pvelectronics

Pvelectronics WiFi NTP Sync Device Manuale utente

Pvelectronics

Pvelectronics IN-8 Guida alla configurazione

Pvelectronics

Pvelectronics Spectrum 18 Guida alla configurazione

Pvelectronics

Pvelectronics Nixie Large Tube Clock Guida alla configurazione

Pvelectronics

Pvelectronics SN-18 Guida alla configurazione

Pvelectronics

Pvelectronics Nixie Maestro Guida alla configurazione

Pvelectronics

Pvelectronics Nixie Maestro Guida alla configurazione

Pvelectronics

Pvelectronics Nixie QTC Manuale utente

Pvelectronics

Pvelectronics Frank 3 Guida alla configurazione

Pvelectronics

Pvelectronics Elite Nixie Guida alla configurazione

Pvelectronics

Pvelectronics Quattro Guida alla configurazione

Pvelectronics

Pvelectronics Halo Chroma Guida alla configurazione

Pvelectronics

Pvelectronics Frank 3 Guida alla configurazione

Pvelectronics

Pvelectronics Nixie 5750 Guida alla configurazione

Pvelectronics

Pvelectronics Frank 2 IN-16 Guida alla configurazione

Pvelectronics

Pvelectronics Frank 3 Guida alla configurazione

Pvelectronics

Pvelectronics Halo Clock Guida alla configurazione

Pvelectronics

Pvelectronics Nixie FunKlock Guida alla configurazione

Manuali Orologio popolari di altre marche

Silicon Laboratories

Silicon Laboratories SI5324 Manuale utente

Heathkit

Heathkit GC-1005 Manuale utente

Oregon Scientific

Oregon Scientific PRYSMA RMR221P Manuale utente

Andrew O'Malley

Andrew O'Malley DOTKLOK Manuale utente

ALGE-Timing

ALGE-Timing ASC3 Manuale utente

Bodet

Bodet Profil 960 Manuale utente

Nixie Clock

Nixie Clock Divergence Meter Manuale utente

La Crosse Technology

La Crosse Technology WS-8256-AL Manuale utente

Mini Gadgets

Mini Gadgets MCPro Manuale utente

Casio

Casio TMR-200 Manuale utente

Progetti

Progetti ILTEMPOSTRINGE Manuale

BVItech

BVItech BV-101 Manuale utente

Progetti

Progetti KALIMERO Manuale

La Crosse Technology

La Crosse Technology WT-3141b Manuale

La Crosse Technology

La Crosse Technology W86531 Manuale utente

Sharp

Sharp SPC900 Manuale utente

La Crosse Technology

La Crosse Technology 404-50447 Manuale utente

Datexx

Datexx DF0063 Manuale utente