Pyle PPBCM22 Manuale utente
Model: PPBCM22
COMPACT BODY CAMERA
INSTRUCTION MANUAL
2
PRODUCT DIAGRAM
Note: For the reset button,open the USB rubber plug and you will nd a hole for the
reset button.
3
Remote Control Key - Optional
LCD SCREEN
REMOTE INDICATOR
PHOTO BUTTON
VIDEO BUTTON
AUDIO BUTTON
4
Press and hold the Power button (located on the bottom-right of the device) for
about 3 seconds, the unit will vibrate with sound and a green indicator on top
of the unit will turn on. The camera and LCD display will turn on and enter into
standby mode. The video preview mode is displayed on the LCD.
Tip: The LCD screen will turn off automatically in about 3 minutes if there is no
operation on the device.
VIDEO RECORDING:
A. To record a video, press the Video Recording button located on the top of
the left side of the device. The unit will vibrate once briey. The red dot symbol
on the LCD display will indicate the camera is currently recording.
B. To mark the video, short press OK button in video recording mode, the lock
icon will be shown on LCD.
C. To record videos at night or in the dark, press Up/Night Vision button once.
Videos recorded in night-vision will be black and white.
D. Press the Video Recording button again to stop recording. The camera
will vibrate once and the red dot symbol will disappear. The camera will stop
recording and save the video.
TAKING PHOTOS:
A. To take a photo, press the Camera button located on the top of the right side of
the device.
B. To take photos at night or in the dark, press Up/Night Vision button once.
Photos taken in night-vision will be black and white.
AUDIO ONLY RECORDING:
To record only audio, press the Audio Recording button located below the
Video Recording button. The unit will vibrate once briey and a microphone
icon will appear on the LCD display. Press the Audio Recording button again to
stop recording. The audio recording will be saved as an audio le.
Getting Started:
5
Camera Use
Power:
Green = On/Standby
Battery:
Video:
Blinking Red = On/Standby
Audio:
Blinking Yellow: Recording
CHARGING:
Via USB:
- You can charge the camera using the
included USB cable and wall charger via any
power outlet.
- You can also charge the camera by plugging
the camera into your computer via the USB
cable.
B. Via single charging dock
- Put the camera into the dock, connect the
dock to power via USB cable.
6
VIDEO, PHOTO, AND AUDIO PLAYBACK:
A. Press the Playback/OK Function button to enter into the Playback Menu.
B. Use the Up/Down button to select the desired icon, and then press the OK
button to display all saved recording les of that type.
C. Select the le to view by using the Up/Down buttons. Press the OK button
on the desired le to view in full screen.
D. To return to the Playback Menu, press the OK button.
E. To return to the preview display, press the Power button.
Tip: While viewing video, press the Up button to rewind and the Down button to
fast forward, both at 2X to 64X speed.
MENU SETTINGS:
To enter into the menu from video preview mode, long press the Audio button.
There are 3 sub-menus: Video Setup, Camera Setup, and System Settings.
Short press the Audio button to move from one tap to the next. And then press
the Menu button to enter into the sub-menu. Press the Audio button when it is
at the System Settings, it will return to the video preview mode.
VIDEO RESOLUTION:
A. In the Video Setup Menu, select the option that displays the current
resolution and press the OK button.
B. There are seven resolution options to select from:
a. 2560×1080 30fps 21:9
b. 2304×1296 30fps 16:9
c. 1920×1080 30fps 16:9
d. 1920×1080 45fps 16:9
e. 1280×720 60fps 16:9
f. 1280×720 30fps 16:9
g. 848×480 30fps 16:9
C. Select the resolution you prefer and press the OK button.
D. Press the OK button again to return to the previous menu.
Camera Use
7
VIDEO QUALITY:
A. In the Video Setup Menu, select “Quality” and press the OK button.
B. There are three options to select from:
a. S.Fine
b. Fine
c. Normal
C. Select the option you prefer and press the OK button.
Tip: This refers to the video bit rate. The higher the setting, the better the video
quality and the larger the video size. To achieve the most battery life, please set
to Normal,
Pre-recording:
A. In the Video Setup Menu, select “Pre-record” and press the OK button.
B. There are two options to select from:
a. On = camera will re-record up to 1min(length depends on the video resolution)
b. Off = pre-recording will be disabled
C. Select the option you prefer and press the OK button.
Tip: When Pre-recording is on, press the Video Recording button to enable pre-
recording, press Video Recording button again to start normal recording.
DELAY-RECORDING:
1. In the Video Setup menu, select “Delay-Record” and press the OK button.
2. There are two options to select from:
a. On = camera will continue recording up to 10sec after stopping
recording(time depends on the video resolution)
b. Off = delay-recording will be disabled
C. Select the “Delay-Record” option you prefer and press the OK button.
STAMP:
1. In the Video Setup menu, select “Stamp” and press the OK button.
2. There are two options to select from:
a. On = camera will record videos with date, time, ID numbers watermark on.
b. Off = stamp will be disabled
Camera Use
8
Camera Use
MOTION DETECTION:
A. In the Video Setup Menu, select “Motion Detection” and press the Menu
button.
B. There are two options to select from:
a. On = device will automatically begin recording when it senses motion.
b. Off = motion detection will be disabled.
C. Select the Motion Detection option you prefer and press the Menu button.
PHOTO RESOLUTION:
A. In the Camera Setup Menu, select the option that shows the current
resolution and press the OK button.
B. There are seven options to select from:
a. 4M( 2688×1512 16:9 )
b. 16M( 5376×3024 16:9 )
c. 18.5M( 4976×3732 4:3 )
d. 20M( 5120×3840 4:3 )
e. 23M( 6400×3600 16:9 )
f. 30M( 6400×4800 4:3 )
g. 32M( 7552×4248 16:9 )
CAMERA QUALITY:
A. In the Camera Setup Menu, select “Quality” and press the OK button.
B. There are three options to select from:
a. S.Fine
b. Fine
c. Normal
C. Select the Camera Quality you prefer and press the OK button.
9
Camera Use
MULTI CAPTURE:
A. In the Camera Setup Menu, select “Multi Capture” and press the OK button.
B. There are four options to select from.
a. Multi Capture 1
b. Multi Capture 5
c. Multi Capture 10
d. Multi Capture 20
C. Select the Multi Capture setting you prefer and press the OK button.
STAMP:
A. In the Photo Setup menu, select “Stamp” and press the OK button.
B. There are two options to select from:
a.On = camera will take photos with date, time, ID numbers watermark on.
b.Off = stamp will be disabled
LANGUAGE SETTING:
A. In the System Setting Menu, select “Language Setting” and press OK
button.
B. There are four options to select from:
a. English
b. Chinese (Simplied)
c. Chinese (Traditional)
d. Russian
C. Select the language option you prefer and press the OK button.
CARD VOLUME:
A. In the System Setting Menu, select “Language Setting” and press OK
button. Camera will show the SD card status. For example as below:
Card Volume
Total: 61471MB
Used: 1302MB
Reserved: 60169MB
B. Press OK button or Audio Recording button to return to System Setting
Menu.
10
Camera Use
RECORD MODE SETTING:
A. In the System Setting Menu, select “Record Mode Setting” and press OK
button.
B. There are two options to select from:
a.Auto Record(camera will start recording automatically the moment camera is
turned on )
b.Manual Record
C. Select the Record Mode Setting option you prefer and press the OK button.
LOOP VIDEO:
A. In the System Setting Menu, select “Loop Video” and press OK button.
B. There are two options to select from:
a.on = once the memory is full the device will begin overwriting the oldest les
b.off
C. Select the Loop Video option you prefer and press the OK button.
DATE AND TIME:
A. In the System Setting Menu, select the current date and time and press OK
button.
B. Press OK button to select the Year/Month/Date/Hour/Minute options.
C. Press Up/Down button to set the time.
D. Press OK button to get to next item and back to previous menu.
DISPLAY SETTING:
A. In the System Setting Menu, select the “Display Setting” and press OK
button.
B. Press OK button to select the LCD Brightness.
C. There is a brightness selecting slide(slide from 0 to 15), press Up/Down
button to set the LCD Brightness you prefer.
D. Press OK button to get back to previous menu, press Audio Recording
button to return to System Menu Setting.
AUTO POWER OFF:
A. In the System Setting Menu, select the “Auto Power Off” and press OK
button.
B. There are three options to choose from:
a.Off = device only powers off manually
b.3min
c.5min
C. Select the Auto Power Off option you prefer and press the OK button.
Indice
Altri manuali Pyle Accessori
Pyle
Pyle PPBCM16 Manuale utente
Pyle
Pyle PPBCM28 Manuale utente
Pyle
Pyle PBC5200 Manuale utente
Pyle
Pyle PBPK42 Manuale utente
Pyle
Pyle Nutrichef PKELKN16 Manuale utente
Pyle
Pyle nutrichef PKESPR26 Manuale utente
Pyle
Pyle PSLBRP4 Manuale utente
Pyle
Pyle Nutrichef PKTCEC4BL Manuale utente
Pyle
Pyle PAD20MXU Manuale utente
Pyle
Pyle PAD15MXU Manuale utente
