Pyle PLML51DB Manuale utente
AM/FM/MP3/USB/AUX Stereo Receiver, Single DIN,
30 Preset Memory Stations, LCD Display
with Remote Control (Black)
PLML51DB
StereoReceiverPowerAmplifier
www.PyleUSA.com
2
INSTALLATION
Preparation
The preparation kit is necessary to mount the radio on the dashboard, this kit is
available at electronics stores and car audio specialists, check the installation
kit before using it to make sure it is the right one for your vehicle.
INSTALL THE DEVICE
1. Lift the left or right top corner of the plastic outer trim ring then pull it out to
remove it.
2. Insert the two bracket keys into the left and right side of the chassis to
separate the chassis from the housing.
3. Install the mounting knob on the board. Check the opening size of the sliding
panel to be mounted. If the measurement is not large enough, carefully cut it
until it slips easily on the opening. Do not force the handle in the opening so
as not to bend it. Locate the series of dubbing tabs above, below and all sides
to be mounted. Completely insert it to the opening of the board, bend the
tabs as necessary towards outside to ensure it ts the board.
4. Slide the stereo into the opening in the dash, ensuring that the wires behind
are tucked and not pinched.
5. Follow the wiring diagram carefully. Verify you've connected them correctly.
CAUTION! Connect the unit to a 12 Volt power source with adequate ground.
6. Now that your wires are all completed, attach the front panel and turn ON the
unit (the vehicle must be switched on). If the unit does not work, check the
calibration again until the problem is solved. With the new car stereo secured
into the bracket, all you need to do is plug the wiring harness back into the
stereo and put the assembly back into place.
7. Slide the stereo into the opening in the dash, ensuring that the wires behind
are tucked and not pinched. Sometimes this may take a few times when the
vehicle has a tight dash opening. Tuck the wires back into an opening behind
the unit.
8. Install the plastic outer trim ring
9. Snap all the pieces of trim back into place over the stereo. Double check that
all screws and trim pieces are securely in place.Try out the new stereo.
Turn the car power on again and play around with the stereo and its settings
to be sure everything is in working order.
www.PyleUSA.com
3
WIRING CONNECTIONS
HARDS FREE PUSH-TO-TALK
PUSH-TO-TALK
• Allows you to access SIRI or GOOGLE voice via Wireless BT.
• Your phone must support SIRI or GOOGLE voice. Once connected to BT, your
phone will ask for access to your contact list.
• Now you are ready to use PUSH-TO-TALK. Press the PUSH-TO-TALK icon.
You are ready to talk. Call "(CONTACT NAME)", the system will call without
having to use your phone.
CONTROL PANEL BUTTONS
15
14192
1
11
3 12
12 13 5 6 7 8 9 10 16 21
18
20
17
4
15A
Front RCA Output(Left) Front RCA Output(Right)
Rear RCA Output(Left)
Rear RCA Output(Right)
EXternal MIC
SWC
SUBWOOFER
Antenna Jack
SUBWOOFER
ANT:RADIO ANTENNA JACK
F-L:Front RCA Output(Left)
F-R:Front RCA Output(Right)
R-L:Rear RCA Output(Left)
R-R:Rear RCA Output(Right)
Power/speaker Connector
FUSE 15A
PRECAUTION
+12V DC
NEGATIVE
EARTH
www.PyleUSA.com
4
CONTROL PANEL BUTTONS
1. (Power)/Mode (source) button
2. SEL (select/menu) button and VOL (volume) knob
3. Back to the previous conguration point;
Press /Bass enhances the pulse function
4. Short press button display clock in all mode. In USB mode, Short press to
select All info/Elapsed time/File info/Track info/clock operation.
Press and hold button turn o illumination on panel and touch any button
to turn on illumination.
5. Folder up
6. Folder down
7. RPT (repeat), button 3 preset
8. RDM (random), button 4 preset
9. (pause/start), preset station 5 button
10. INT (intro), preset button 6 station
11. Press and hold BND button to activate SIRI. Short press BND button
to change band. Short press BND button to pick up/cut o phone call.
12. (tune back, search back, crawl back, fast reverse)
13. (tune forward, search forward, crawl forward, fast forward)
14. IR remote control sensor
15. LCD screen
16. AS (automatic storage/preset station search, automatic search)
17. USB port
18. AUX IN (auxiliary input)
19. MIC input (integrated microphone)
20. In power ON mode, press the MUTE button to toggle mute ON or OFF.
21. Release front panel
21. RESET
GENERAL OPERATION
Turn Unit ON/OFF
• Press the power /Mode button on the front panel to turn ON the unit, and
press and hold it again to turn OFF the unit.
• Press the power button on the remote control to turn the unit ON or OFF.
www.PyleUSA.com
5
Adjust Volume (VOL)
Rotate the VOL knob on the front panel or press the VOL+ /VOL- button on
the remote control to increase or decrease the volume level.
FUNCTION
Press the Volume knob and Rotate to select Audio/Display/Tuner/Clock/Beep/
Animation/Demo mode function. Press the Volume knob again to select desire
function mode.
AUDIO MODE
• Press the Volume knob and Rotate to select SW Level/Manual EQ/Q factor/
Preset EQ/Bass boost/Loudness/Subwoofer set/Fader/Balance/X’Over/DTA
Setting/Car type.
• Press and hold Volume knob to select 2 way/3 way X’Over mode.
SW LEVEL
Press the Volume knob and Rotate to select -13 ~ +13 level.
MANUAL EQ
Press the Volume knob and Rotate to select 25 band frequencies level.
Q FACTOR
Press the Volume knob and Rotate to select 1/1.5/2.5/3.5 different Q factor value.
PRESET EQ
Press the Volume knob and Rotate to select user/Natural/Rock/Pop/Easy/
Top 40/Jazz/Powerful.
BASS BOOST
Press the Volume knob and Rotate to select Bass boost level.
LOUDNESS
Press the Volume knob and Rotate to select Loudness level.
SUBWOOFER SET
Press the Volume knob and Rotate to switch ON/OFF.
FADER
Press the Volume knob and Rotate to select Fader position.
BALANCE
Press the Volume knob and Rotate to select Balance position.
www.PyleUSA.com
6
X’OVER
Press the Volume knob and Rotate to select Tweeter/Front HPF/Rear HPF/
Subwoofer LPF.
TWEETER
Press the Volume knob and Rotate to select Frequency/Gain left/Gain right.
FRONT HPF
Press the Volume knob and Rotate to select Frequency/Gain.
REAR HPF
Press the Volume knob and Rotate to select Frequency/Gain.
SUBWOOFER LPF
Press the Volume knob and Rotate to select Frequency/Gain/Phase.
DTA SETTING
Press the Volume knob and Rotate to select Position/Distance/Gain/Data Reset/
Delay Unit.
CAR TYPE
Press the Volume knob and Rotate to select Small/Medium/Large car type.
DISPLAY
Press the Volume knob and Rotate to select Color Select/Spectrum/ID3 tag/
Version/Dimmer.
DIMMER
• Press the Volume knob and Rotate to select ON/OFF/Dimmer Time.
• Press the Dimmer Time to setting ON Time/OFF Time.
LANGUAGE SELECTION
Press Volume button to select language, turn the knob to select English/Russian.
COLOR SELECT
Press the Volume knob and Rotate to select custom R/G/B/ Variable Scan/Red/
Pink/Purple/Blue/Cyan/Green/Yellow/Orange.
www.PyleUSA.com
7
SPECTRUM
Press the Volume knob and Rotate to switch ON/OFF.
ID3 TAG
Press the Volume knob and Rotate to switch ON/OFF.
VERSION
Press the Volume button to check software version.
TUNER
Press the Volume button to select Local Seek/Mono Set/Regional/RDS Set.
LOCAL SEEK
Press the Volume button to rotate switch ON/OFF.
MONO SET
Press the Volume button to rotate switch ON/OFF.
REGIONAL
Press the Volume button to rotate to select country regions.
RDS SET
Press the Volume button to rotate switch ON/OFF.
CLOCK
Press the Volume knob and Rotate to select Clock Format/Clock adjust/Date
Format/Date Set.
BEEP
Press the Volume button to rotate switch ON/OFF.
ANIMATION
Press the Volume knob and Rotate to select ON/OFF and time interval of
animation time.
DEMO MODE
Press the Volume button to rotate switch ON/OFF.
www.PyleUSA.com
8
Set the clock (CLK)
1. To display the Time press the CLK button.
2. To set the time, press and hold the CLK button and the time will start ashing.
3. Press the or button on the front panel or on the remote control to set
the time.
4. Press the CLK button and the minutes will start ashing.
5. Press the or button on the front panel or on the remote control to set
the minutes.
6. Short Press to Increase Bass Level
Change the source mode (SRC)
Press the SRC button to switch between the button RADIO, BT (Wireless BT),
USB (with a USB device inserted), AUX-IN mode (input assistant).
Loudness: LOUD ON/OFF
Press the LOUD button on the remote control to change the loud volume to
boost the bass output frequency, press again, to turn it o.
DSP SMART ANDROID/IOS APP CONTROL
Preset Equalizer (EQ)
Press the EQ button on the front panel or on the remote control to switch
between EQ, OFF, CLASS, ROCK, POP, FLAT.
USB port
The USB port on this stereo device is designed for playing media from USB
memory devices.
Subwoofer Control Time Alignment Control
25 EQ ControlX’Over Control
www.PyleUSA.com
9
GENERAL OPERATION
Integrated Microphone
For voice reception when making a call using the hands-free system.
Auxiliary Input Connector
3.5mm auxiliary input stereo is designed for devices with line output 3.5 mm or
hearing aids.
Reset System
The RESET button is used to reset all factory settings parameters, this function
can be used when the LCD screen does not work properly or if the sound is
distorted, or when some of the controls are disable. Press the RELEASE button
to release the front panel and remove it, use a thin object with a small tip to
press the RESET button over 6 second.
Subwoofer Level Control
Select function to select audio, entry subwoofer, entry sw level, turn the knob
to select level 0-8.
Subwoofer Frequency Control
Select function to select audio, entry subwoofer, entry sw frequency, turn the
knob to select 80Hz/120Hz/160Hz.
RADIO OPERATION
Change Bands (BAND)
Press the BAND button to switch between the AM1, AM2, FM1, FM2, FM3,
WB (weather) bands. Each band stores up to six preset stations.
Manual Tuning ( /)
Press and hold the or button on the front panel or on the remote control
to enter manual tuning mode. In manual tuning mode, press the or
button to move the radio frequency number up or down one step.
Auto Seek Tuning ( /)
In standby mode or while not in manual tuning mode, quickly press the or
button to move to the next/previous available station automatically.
www.PyleUSA.com
10
To Store/Recall Preset Stations
The radio can store 6 pre-set stations for each band (WB, AM1, AM2, FM1, FM2
and FM3) for a total of 36 preset stations.
Memorize a station
• Turn the radio on and select the desired band and station.
• Select a station by or button.
• Press and hold the desired preset button (numbered 1-6 on the face of the
radio) for more than 2 seconds to save the station to that preset number.
To recall a preset station
• Select the desired band.
• Briey press a preset button (numbered 1-6) to recall the corresponding
preset station.
Automatic Store station/Preset station scan (AMS)
Press and hold the AMS button for more than 2 seconds to select six strong
stations and store them in the current band. The radio will automatically scan
the current frequency and enter the six strongest stations into the preset
memory positions for that band. Briey press the AMS button on the remote
control to recall each preset station that saved in the memories in each band.
LOCAL/DX
In urban areas, most stations are strong enough and“LOCAL ON” mode should
be selected. Switch to LOCAL OFF mode to search for stations with weaker
signals. Press the LOC button on the remote control to choose local or distant
reception mode.
STEREO/MONO
FM station is received in stereo mode. However, if the signal is weak or reception
is not as good as you would like, switching to MONO mode usually improves
the overall sound quality. Press the ST button on the remote control to choose
FM STEREO or MONO audio eect.
USB OPERATION
Insert USB
To play les from a USB device, open the USB port cover and insert the USB
device into the port, the songs will begin to play automatically.
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Pyle Amplificatore
Pyle
Pyle PDA5BU.0 Manuale utente
Pyle
Pyle PT4601AIU Manuale utente
Pyle
Pyle PMSA20 Manuale utente
Pyle
Pyle PCM20A Manuale utente
Pyle
Pyle PWMA80UFM Manuale utente
Pyle
Pyle PFA560BT Manuale utente
Pyle
Pyle PTA4 Manuale utente
Pyle
Pyle PFA330BT Manuale utente
Pyle
Pyle PFA330BT Manuale utente
Pyle
Pyle PDA6BU Manuale utente
Pyle
Pyle PWMA150 Manuale utente
Pyle
Pyle PQ1000 Manuale utente
Pyle
Pyle PT250BA Manuale utente
Pyle
Pyle PWMA200 Manuale utente
Pyle
Pyle PCAU25A Manuale utente
Pyle
Pyle PMX401 Manuale utente
Pyle
Pyle PTAU23 Manuale utente
Pyle
Pyle PP444 Manuale utente
Pyle
Pyle PDA5BU Manuale utente
Pyle
Pyle PHE1AW Manuale utente
