Pyro Products Pyro Tower Manuale utente
Pyro Tower Assembly Manual
12/16
WARNING: FOR YOUR SAFETY
1. This appliance is for outdoor use only and should NOT be used in a building, garage, or any other enclosed area.
2. Do NOT use this outdoor fire pit for indoor heating. TOXIC carbon monoxide fumes can accumulate and cause
asphyxiation.
3. This outdoor fire pit is NOT recommended for unsupervised use.
4. This outdoor fire pit is NOT to be operated by children.
5. This outdoor fire pit is NOT to be used in or on boats or recreational vehicles.
6. Always use in accordance with all applicable local, state, and national codes. Contact your local fire department for
details on outdoor burning.
7. When using this outdoor fire pit, exercise the same precautions you would with any open fire.
8. The use of alcohol, prescription or non‐prescription drugs may impair the consumer’s ability to properly assemble or
safely operate this outdoor fire pit.
9. Do NOT use this outdoor fire pit without reading this “Owner’s Manual.”
10. This outdoor fire pit is for use with dry, seasoned hardwood. It will burn hotter, more completely and create less smoke.
11. Do NOT burn manufactured logs, driftwood, trash, leaves, paper, cardboard, plywood, painted or stained or pressure
treated wood. Avoid using soft woods such as pine or cedar that can throw sparks.
12. Do NOT alter this outdoor fire pit in any manner.
13. Do NOT use this outdoor fire pit until it is completely assembled.
14. Do NOT store or use gasoline or other flammable vapors or liquids in the vicinity of this or any other appliance.
15. Do NOT store or use an LPG cylinder within 10 feet of this outdoor fire pit while it is in operation.
16. Do NOT use this outdoor fire pit near automobiles, trucks, vans or recreational vehicles.
17. Do NOT use in an explosive atmosphere. Keep outdoor fire pit area clear and free from combustible materials, gasoline
and other flammable liquids.
18. Do NOT use this outdoor fire pit under any overhang or near any unprotected combustible constructions. Avoid using
near or under any overhanging trees or shrubs.
19. Always empty this outdoor fire pit before each use once the fire pit has cooled COMPLETELY. Leave a thin layer of ash
to protect the bottom of the base.
20. Do NOT wear flammable or loose clothing when operating this fire pit.
21. Do NOT use in windy conditions.
22. Do NOT use gasoline, kerosene, diesel fuel, lighter fluid or alcohol to light or re‐light fires.
23. Keep all electrical cords away from a hot fire pit.
24. All surfaces of this outdoor fire pit are hot when in operation. To avoid burns, do NOT touch any part of the fire pit until
it has cooled completely. Wear protective gear (i.e. potholders, gloves, BBQ mittens, hot pads, etc.) to handle any parts.
NEVER touch ashes or coals to see if they are hot.
25. Do NOT leave a lit outdoor fire pit unattended, especially around children and pets.
26. Do NOT attempt to move or store this outdoor fire pit until all ashes and coals are completely extinguished.
27. Do NOT remove ashes or coals until they are completely and fully extinguished.
28. Use heat resistant gloves or hot pads when touching any surfaces of the fire pit.
29. Only use the fire tool provided to add or move logs.
30. Do NOT place wood or charcoal directly into bottom of the outdoor fire pit. Place wood only on the LOG grate.
31. Do NOT overload the fire pit. Do not add additional firewood until the fire burns down. NOTE: If any portion of the tower,
lid or spark guard/firescreen of this outdoor fire pit are glowing, your fire is TOO BIG and the fire pit is overloaded.
33. Do NOT lean over this outdoor fire pit when lighting or while in use.
34. Do NOT place a hot spark guard/firescreen or hot fire tool onto a combustible surface such as grass, wood or furniture.
35. Avoid breathing smoke from the fire and avoid getting it into your eyes.
36. This outdoor fire pit should be thoroughly inspected and cleaned on a regular basis.
37. After a period of storage and/or non‐use, check for signs of damage and creosote build‐up. Do NOT operate until
necessary repairs and/or clean up are executed.
38. Death, serious injury or property damage may occur if the above is not followed exactly.
CAUTION: If you intend to use this item on a wooden deck or other combustible surface, or any surface that is not entirely
resistant to high heat, you MUST use the spark screen to prevent sparks or burning material from coming into contact with
the ground or surrounding area. A non‐flammable and heat resistant material such as concrete pavers, brick, or stone
between the fire pit and the surface must also be used if the optional Pedestal Base is not attached.
Hardware List
1
Two bags of hardware are included with your Pyro Tower. The first bag contains
hardware for assembling the four side pieces of the tower. The second bag
contains hardware for assembling the four side pieces to the bottom base.
1/4” Zinc Lock Washer
1/4” Zinc Flat Washer
1/4” Stainless Lock Washer
1/4” Stainless Socket Head Cap Screw
1/4” Zinc Hex Nut
Shoulder Tabs
1/4” Zinc Lock Washer
1/4” Zinc Flat Washer
1/4” Zinc Carriage Bolt
1/4” Zinc Hex Nut
Shoulder Tabs
Tower Bag
Base Bag
Qty. 12
Qty. 12
Qty. 12
Qty. 12
Qty. 12
Qty. 12
Qty. 6
Qty. 6
Qty. 6
Qty. 6
Qty. 6
2
Parts List
Your Pyro Tower is constructed from 3/16” steel and requires four boxes for
safe shipping because of the size and weight of the pieces. Below you will find
a description of the parts contained in each box:
Tower Side Pieces
Tower Back Piece
Tower Front Piece
Removable Shelf
Firewood Basket
Tower Base
3
Base Description
Below is an overview of the various holes and slots on the Pyro Tower Base:
Drain Holes
Carriage Bolt Holes
Slots for Tower Pieces
Slots for optional
Pedestal Legs
4
Tower Front/Rear Description
Slots for Removable
Shelf
Tabs
Bolt Hole
Slot for Shoulder Tab
Air Vents
Bolt hole for
optional vent
louvre (comes
with cooking kit)
5
Tower Side Pieces Description
Slots for Front/Back Panel Tabs
Slot for Shoulder Tabs
Tabs
6
Tab and Slot Design
The Pyro Tower is designed with a unique tab and slot assembly that will align
all of the pieces in position before being secured together with the included
hardware.
Tab on Tower Front
Corresponding Slot
on Tower Side Piece
7
Shoulder Tabs
The Shoulder Tabs are inserted into the smaller slots on the Tower Side Pieces.
The hole in the Shoulder Tab will align with the hole on the Front and Rear
Tower Pieces where a bolt is inserted to secure the pieces together.
Shoulder Tab
Corresponding Bolt
Holes
Shoulder Tab Alignment
Shoulder Tab Inserted
Insert Bolt Here
8
Bolt Hardware Sequence
Below is a description of the proper assembly sequence to secure the Pyro
Tower hardware:
Bolt
Flat Washer
Shoulder Tab
Flat Washer
Lock Washer
Hex Nut
Indice
