Qlogic ISR6200 Manuale utente

[Quick Start Guide ]

QUICK START GUIDE

INTELLIGENT STORAGE ROUTER INSTALLATION

iSR6200

Purchasers of OEM products should consult with the OEM for support.

Please feel free to contact your QLogic approved reseller or QLogic Technical Support at

any phase of integration for assistance. QLogic Technical Support can be reached by the

following methods:

Web http://support.qlogic.com

E-mail support@qlogic.com

The QLogic knowledge database contains troubleshooting information for the QLogic

adapters. Access the database from the QLogic Support Web page,

http://support.qlogic.com. Use the Support Center search engine to look for specific

troubleshooting information.

Quick Start Guide

The QLogic iSR6200 is an Intelligent Storage Router that provides servers with iSCSI connectivity to SAN-attached Fibre

Channel based disk or tape storage.

Suggested Configurations

Figure 1 shows the iSR6200 connecting iSCSI servers to a direct-attached storage array.

Figure 1. iSR6200 in Direct Attach Configuration

Figure 2 shows the iSR6200 connecting iSCSI servers to a SAN-attached array.

Figure 2. iSR6200 in SAN-Attach Configuration

iSCSI

Server

IP Switched

Network

iSR6200

Fibre

RAID-Based Fibre

Channel Storage System

Initiator

Channel

Server

iSCSI

Initiator

iSCSI

IP Switched

Network

iSCSI

iSR6200

Fibre

Fibre Channel

RAID-Based

Fibre Channel

Storage Systems

Channel

Fibre

Channel

SAN

Fibre Channel

SAN

Installation Instructions

This quick start guide provides procedures for installing and configuring your new QLogic iSR6200 router.

■Step 1. Verify the package contents.

■Step 2. Complete the pre-installation checklist.

■Step 3. Mount the router.

■Step 4. As needed, insert additional blade into router.

■Step 5. Install the small form factor pluggables (SFPs).

■Step 6. Apply power to the router.

■Step 7. Install SANsurfer®Router Manager (SANsurfer iSCSI/FC Router Manager).

■Step 8. Configure the iSR6200 management port IP address.

■Step 9. Run the configuration wizard.

■Step 10. Present LUNs to iSCSI initiators.

■Step 11. Configure second blade (if provided).

Step 1. Verify the Package Contents

Verify the contents of the purchased production package, either C12 or B10.

The iSR6200 router production package (C12) includes the following hardware components:

■iSR6200 router chassis with two blades installed

■DB9 to RJ45 cable adapter

■Power cable (6 foot black)

■Rail Mounting Kit, part number 50990-00

■WEEE Conformance card

■Read Me First card

■China RoHs Electronic Info, RoHs Switch/Power/Fan SKUs Toxic Substance (Chinese Vers) 20 Years

■iSR6200 Quick Start Guide (this document)

The standalone blade production package (B10) includes the following hardware components:

■One blade

■SFPs

■WEEE Conformance card

■Read Me First card

■China RoHs Electronic Info, RoHs Switch/Power/Fan SKUs Toxic Substance (Chinese Vers) 20 Years

■iSR6200 Quick Start Guide (this document)

Step 2. Complete the Pre-Installation Checklist

During the initial configuration process, the system prompts you to enter information for each blade contained in the

iSR6200. Use the spaces provided in the following tables to record the IP addresses for each blade.

Table 1. Worksheet for Router Blade 1 (left) Parameters

Symbolic name of the iSR6200 Blade 1

Management port IP address, subnet

mask, and gateway (if not using DHCP)

iSCSI port 1 IP address, subnet mask,

and gateway (GE-1)

IP address of the Internet simple name

service (iSNS) server for iSCSI port 1 (if

iSNS will be enabled)

iSCSI port 2 IP address, subnet mask,

and gateway (GE-2)

IP address of the iSNS server for iSCSI

port 2 (if iSNS will be enabled)

iSCSI port 3 IP address, subnet mask,

and gateway for the optional (FC3, GE-3,

or 10GE-3) port

IP address of the iSNS server for iSCSI

port 3 (if iSNS will be enabled)

iSCSI port 4 IP address, subnet mask,

and gateway for the optional (FC4, GE-4,

or 10GE-4) port

IP address of the iSNS server for iSCSI

port 4 (if iSNS will be enabled)

Table 2. Worksheet for Router Blade 2 (right) Parameters

Symbolic name of the iSR6200 Blade 2

Management port IP address, subnet

mask, and gateway (if not using DHCP)

iSCSI port 1 IP address, subnet mask,

and gateway (GE-1)

IP address of the iSNS server for iSCSI

port 1 (if iSNS will be enabled)

iSCSI port 2 IP address, subnet mask,

and gateway (GE-2)

IP address of the iSNS server for iSCSI

port 2 (if iSNS will be enabled)

Step 3. Mount the Router

To mount the iSR6200 router in the rack, follow the instructions (QLogic 6200 Storage Router Rack Mounting Guide)

provided in the rack mount kit.

Step 4. Insert Additional Blade into Router (As Needed)

If you have purchased an additional blade (B10), insert it into the iSR6200 router as follows:

1. Move the ejector latch handle to a position horizontal to the base.

2. Slide the blade into an open chassis slot.

3. When the blade is completely inserted, raise the ejector latch handle to snap the blade into place.

Step 5. Install the SFPs

An SFP transceiver is required for each router port that will be connected to a Fibre Channel device or switch. SFPs are

included in the package. If you prefer to use SFP transceivers other than the ones provided, purchase one of the QLogic

recommended transceivers listed in Table 3.

To install an SFP transceiver, insert the transceiver into the router port, and then press gently until it snaps in place. The

transceiver will fit only one way. If the transceiver does not install under gentle pressure, flip it over and try again.

iSCSI port 3 IP address, subnet mask,

and gateway for the optional (FC3, GE-3,

or 10GE-3) port

IP address of the iSNS server for iSCSI

port 3 (if iSNS will be enabled)

iSCSI port 4 IP address, subnet mask,

and gateway for the optional (FC4, GE-4,

or 10GE-4) port

IP address of the iSNS server for iSCSI

port 4 (if iSNS will be enabled)

Table 3. Recommended Replacement Transceivers

8Gb Transceivers 10Gb Transceivers

Manufacturer Part Number Manufacturer Part Number

Finisar®FTLF8528P2BCV-QL Finisar FTLX8571D3BCL

JDS Uniphase®PLRXPL-VC-SH4-22-N-Q

PLRXPL-VC-SH4-23-N-QL

JDS Uniphase PLRXPL-SC-S43-22-N

Table 2. Worksheet for Router Blade 2 (right) Parameters (Continued)

Step 6. Apply Power to the Router

The iSR6200 router chassis contains one or two router blades, along with a power cooling module (PCM) for each blade.

Each chassis blade provides light emitting diodes (LEDs) and connectors that face the front of the chassis. Each PCM

provides a power connector, as well as an LED (see Figure 3).

Figure 3. iSR6200 Router Chassis—Front and Back Plates

1. Attach the AC power cord to the power connector, located on the back of the PCM connected directly

behind the router blade.

2. Connect the opposite end of the power cord to the wall outlet or power strip.

3. Check the PCM power LED to make sure the PCM is operational (green = power, yellow = no AC power).

Figure 4 shows the location of the ports and LEDs on one of the blades contained within the iSR6200

unit.

Figure 4. iSR6200 Blade Ports and LEDs

4. Verify that the router’s input power LED is illuminated.

The iSR6200 router runs its self test and begins normal operation—this may take a minute.

5. Verify that the heartbeat LED is blinking (once per second), and that the system fault LED is not

illuminated.

MGMT IOIOI

FC1 FC2

MGMT IOIOI

FC1 FC2

10GbE1 iSR6250

Intelligent Storage Router

10GbE2

10GbE1 iSR6250

Intelligent Storage Router

10GbE2

Front Plate iSR6200 Blade 1 Front Plate iSR6200 Blade 2

Back Plate PCM for Blade 2 Back Plate PCM for Blade 1

PCM Status LED Power Connector PCM Status LED Power Connector

Blade Option Ports Based on Model Blade Option Ports Based on Model

MGMT IOIOI FC1 FC2 GE1 GE2

GE4 GE3 iSR6240

Intelligent Storage Router

iSR6200 System

10GbE1 iSR6250

Intelligent Storage Router

10GbE2

RS232 Port Heartbeat LED Power LED Blade Option Ports Based on Model

Management Port System Fault LED Fibre Channel Ports iSCSI Ports

The iSR6260 router blade (see Figure 5) adds two more Fibre Channel ports to the blade configuration.

Each port has the following capacity:

❑Auto negotiating transmission rates of 2, 4, or 8Gb

❑Hot pluggable SFP Fibre Channel connector

❑N_Port, NL_Port, or transparent port type

Figure 5. Fibre Channel Ports on the iSR6260 Router Blade

The iSR6250 router blade (see Figure 6) adds two 10Gb Ethernet ports to the blade configuration.

Each port has the following capacity:

❑10GbE iSCSI ports that run in full duplex mode

❑Support for jumbo frames

❑IPv4 and IPv6 protocol support

❑iSCSI header and data digest in the software

Figure 6. 10Gb Ethernet Ports on the iSR6250 Router Blade

The iSR6240 router blade (see Figure 7) adds two iSCSI Ethernet ports to the blade configuration.

Each port has the following capacity:

❑Auto negotiating transmission rates of 100 and 1000Mbps

❑Full duplex transmission mode

❑Support for jumbo frames (at 1000Mbps only)

❑RJ45 copper Ethernet connector type

❑iSCSI header and data digest in the hardware

❑IPv4 and IPv6 protocol support

❑iSCSI offload

Figure 7. iSCSI (GE) Ports on the iSR6240 Router Blade

For installation details, diagnostics, and troubleshooting, see the iSR6200 Intelligent Storage Router Installation Guide.

8Gb (Yellow) 4Gb (Green) 2Gb (Amber)

SAN (Green)

LAN (Green)

Activity

Link Status

Step 7. Install SANsurfer Router Manager

Follow these steps to download the SANsurfer iSCSI/FC Router Manager tool from the QLogic Web site and install it on

a PC workstation:

1. Close all programs currently running.

2. Go to the QLogic download site:

http://support.qlogic.com/support/drivers_software.aspx

3. Click the Intelligent Storage Routers icon.

4. Select your iSR62xx model number, and then click Go.

5. On the iSR62xx download page under Management Tools, click the link to the SANsurfer Router

Manager version for your operating system.

6. Read the license agreement, and then click Agree to continue.

7. Follow the system prompts to save the tool to your workstation, and then install it.

Step 8. Configure the iSR6200 Management Port IP Address

1. Using a switch or hub, connect the router’s management port (10/100 Ethernet) to your workstation.

As an alternative, you may directly connect your workstation to the router using an Ethernet crossover

cable.

The iSR6200 management port’s default IP address is 10.0.0.1, subnet 255.0.0.0. Make sure the

workstation connected to the iSR6200 router has Ethernet address 10.0.0.x, where xis other than 1

and subnet mask is 255.0.0.0.

2. From the workstation, open a command window and using a Telnet session, follow these steps:

a. Connect to the iSR6200 using IP address 10.0.0.1.

b. Log in as guest, and use the password password.

The following shows the iSR6200 command line interface (CLI) window.

iSR6200 login: guest

Password:

******************************************************

* *

* ISR6200 *

* *

******************************************************

iSR6200 #> blade 1

iSR6200 <1> #> admin start -p config

iSR6200 <1> (admin) #> set mgmt

A list of attributes with formatting and current values will follow.

Enter a new value or simply press the ENTER key to accept the current value.

If you wish to terminate this process before reaching the end of the list

press 'q' or 'Q' and the ENTER key to do so.

WARNING:

The following command might cause a loss of connections to the MGMT port.

IPv4 Interface (0=Enable, 1=Disable) [Enabled ]

IPv4 Mode (0=Static, 1=DHCP, 2=Bootp, 3=Rarp) [Dhcp ] 0

IPv4 Address [10.0.0.1 ] 172.17.136.55

IPv4 Subnet Mask [255.0.0.0 ] 255.255.254.0

IPv4 Gateway [0.0.0.0 ] 172.17.136.1

IPv6 Interface (0=Enable, 1=Disable) [Disabled ]

All attribute values that have been changed will now be saved.

Connect to host lost.

3. Select the blade you want to configure by entering one of the following CLI commands:

blade 1

blade 2

4. At the prompt, enter the following CLI commands (for blade 2):

iSR6200 (admin)#> admin start (the default password is config)

iSR6200 (admin)#> set mgmt

5. Specify the mode. QLogic recommends using a static address. Select option 0, and then enter the IP

address, subnet mask, and gateway, if applicable.

You will lose the connectivity of the Telnet session at this time.

6. If you want to continue using the CLI, restart the Telnet session with the IP address you just assigned

to the management port.

You now have the management port configured with the appropriate IP address.

7. Connect the management port cable to your Ethernet network. Connect cables to the iSCSI and Fibre

Channel ports (GE1, FC1, and FC2, as well as the blade option ports based on model), as shown in

the configuration diagrams (Figure 1 and Figure 2).

8. If necessary, repeat these procedures to configure your second blade.

Step 9. Run the Configuration Wizard

1. On the computer that will manage the iSR6200, start SANsurfer iSCSI/FC Router Manager that you

installed in Step 7.

You should see the windows shown in Figure 8.

2. On the toolbar, click Connect.

3. In the Connect to Router dialog box, enter the IP address of the iSR6200 you want to configure, and

then click Connect.

4. In the left pane, select the router blade to be configured (Blade 1 or 2).

SANsurfer iSCSI/FC Router Manager prompts you to start the General Configuration Wizard.

5. To start the configuration wizard, click Yes.

Altri manuali per iSR6200

Indice

Altri manuali Qlogic Magazzinaggio

Qlogic

Qlogic SANbox 8200 Manuale

Manuali Magazzinaggio popolari di altre marche

QNAP

QNAP TS 32PXU Series Manuale utente

LaCie

LaCie RUGGED RAID Manuale utente

Freecom

Freecom CLS DOCK Manuale utente

PNY

PNY Attache P-FD64MBATT3 Manuale utente

HP StorageWorks MSL2024 Manuale utente

OLT

OLT 6x6 Maximizer Manuale utente

Transcend

Transcend JetFlash 160 Manuale utente

LaCie

LaCie RUGGED MINI Manuale utente

Thunderbolt

Thunderbolt 600 Manuale utente

Panasonic

Panasonic LB-DH8 series Manuale

Intel

Intel RAID High Availability Manuale utente

LaCie

LaCie 12big Thunderbolt 3 Manuale utente

Spectra Logic

Spectra Logic T-Series Spectra T50e Manuale utente

Panasonic

Panasonic LKM-F931-1 Manuale utente

Tabernus

Tabernus Enterprise Erase E2400 Manuale utente

Rocstor

Rocstor COMMANDER 3F series Manuale utente

HP P9000 Manuale utente

Western Digital

Western Digital Ultrastar Data60 Manuale utente

Qlogic iSR6200 Manuale utente

Manuali Magazzinaggio popolari di altre marche