Qoltec DVT123SA Manuale utente
ACTION CAMCORDER 50203
USER MANUAL
0
End User Notice:
High de inition and high rame rate video capture
devices,place huge demands on memory cards.
Pending your user settings,it is recommended that a
4GB(or higher) CLASS 10 SD Card be used to avoid
Read/Write complications, which will appear as an
error message on the screen during use. I you are not
sure,please test any lower class cards (Read/Write
speed) in the device be ore use.
1
Mounting Accessories
2
WATERPROOF CASE
1. Insert a finger at the half circle of the Clamp by prying the clamp up away from the case.
2. Before sealing the case, inspect the water sealing gasket to be sure it’s in good condition. ou can test the
gasket by closing the case without inserting the camera.
3
1.Clamp
2. Shutter Release
3. Power Button
Submerse the case completely in a bowl of water for about a minute. Remove the case from the water, dry off
its exterior with a towel, then open the case. If the entire interior is dry, the case and gasket are safe for use under
water.
3. There are just two buttons required for recording video and images: the Shutter Release, and the Power
Button.
4. Remember to put the Mode Switch in your desired recording position before inserting the camera in the
waterproof case. There is no external button for the Mode Switch.
4
1.
4
1
-20 Screw
HANDLEBAR SEATPOST MOUNT
1. The camera dose not have a standard tripod mount. For all the accessories with a 1/4-20 screw, the camera
must be enclosed in with the waterproof case or in the included mounting adapter.
2. Turn the waterproof case (or mounting adapter) clockwise onto the 1/4-20 screw of the handlebar clamp until
5
2. Locking Wheel
3. Bar Clamp Bolt
4. Bar Clamp
5. Tilt Knob
secure.
3. Turn the Locking Wheel so it applies pressure to the case to keep the connection secure.
4. Loosen the Bar Clamp Bolt until the screw can be pushed 90°upward.
5. The bottom half of the Bar Clamp can be opened to allow you to wrap the Handlebar Clamp around the actual
handlebar of your bicycle.
6. After positioning the Handlebar Clamp where you want it, close up the bottom half of the clamp and tighten
the Bar Clamp Bolt.
7. Loosen the Tilt Knob, to adjust for the proper aiming angle; then tighten the knob.
8. Panning adjustments can be made by loosening the Locking Wheel, adjust the pan angle; then tighten the
wheel.
6
3.
4
1
-20 Screw
HELMET MOUNTING SYSTEM
1. Insert the free end of the Helmet Belt through one of the slots in the base of the Helmet Mount.
2. Thread the same end in to the helmet vent and then back up to the Helmet Mount through another vent. Then
insert the belt through the other side of the Helmet mount. Then insert the belt back through the helmet vent.
3. ou should have now both ends of the belt inside the helmet. take both ends of the Belt and pull to tighten and
7
1.Helmet Belt
2.Helmet Mount
4.Locking Wheel
5.Tilt Knob
then attach together with the Velcro strap.
4. Turn the Waterproof case (or mounting adapter) onto the 1/4-20 screw of the Helmet Mount until secured.
5. Turn the Locking Wheel so it applies pressure to the case to keep the connection secure.
6. Loosen the Tilt Knob, to adjust for the proper aiming angle; then tighten the knob.
7. Please note this helmet mount will only work with vented helmets.
8
SHIELD
1. This Mounting Adapter allows you to attach mounting accessories that have a 1/4-20 screw.
2. The camera will clip right in to this adapter.
9
Indice
Altri manuali Qoltec Fotocamera d'azione
