Qomo QD3900H2 Manuale utente
QD3900H2
User Manual
Model: QD3900H2
V1.0.38
Contents
Parts Identification.......................................................... 2
Control Panel............................................................... 3
Remote Control............................................................... 4
Making Connections........................................................ 6
Menu Operating Instructions.......................................... 9
Basic Operation ............................................................. 11
USB Port ........................................................................ 15
Folding The Unit ............................................................ 20
Problems And Solutions ................................................ 21
Specifications ................................................................ 22
- 1 -
Precautions
●
Please follow these precautions:
To prevent
fire or shock hazard, do not expose the unit to rain or moisture.
To prevent
electrical shock, do not open the cabinet. Refer to qualified
personnel for service only.
Do not use
the unit continuously for more than 24 hours with
camera
auto focus
on. It may cause damage to the camera lens.
Be careful not to
spill water or other liquids onto the unit, or allow combustible or
metallic objects to get inside the cabinet.
Unplug
the visualizer from the wall outlet when it is not in use for an
extended period of time.
Clean cabinet
with a soft cloth lightly moistened with a mild
detergent.
Clean lens
carefully with an air spray or soft dry cloth
to avoid scratching.
When lamps
flash or become dark, they
should be replaced with new ones.
Avoid
interchanging arm
lamps and bottom lamp frequently.
- 2 -
2
5
1
3
4
6
7
1
1
1
1
1
8
9
Parts Identification
7
8
9
10
11
12
13
14
Zoom in/Zoom out Knob
Camera Stand
Left Arm Lamp
Bottom Lamp
Remote Control Slot
Control Panel
Camera Case
Infrared Receive Area
Rear Connector
Right ArmLamp
Work Stage
Side Connector
Built-in Microphone
SD Card Slot
- 3 -
Control Panel
●
Button operation instruction
Button
Function
Power On/Off, press and hold 3 seconds to off
To show or hide OSD menu/Delete button in playlist
Select Visualizer input signal
Capture a still image，It's better to insert external storage
.
Record a video clip, press it again to stop recording.After
inserting external storage
Freeze the image, press again to unfreeze.
Hold Freeze button for 3s enter/exit split
Re-display stored imaged and videos
Image rotation of
90°
,
180°
,
270°
Select resolution from XGA, SXGA, WXGA, 720P, 1080P,800P
and 1200p
directly
Control the arm lamp and bottom lamp
Automatic white balance, auto focus and auto adjust
brightness
Move the cursor Left/zoom out
Move the cursor Right/zoom in
Move the cursor Up/Increase the brightness
Move the cursor Down/Decrease the brightness
Confirm key
Projector On/Off, press and hold 3 seconds to off
Select Projector input signal
- 4 -
Remote Control
Power
Control the visualizer On/
Off
Lamp
Control the arm lamp and
bottom lamp
Auto
Automatic white balance,
auto focus and auto adjust
brightness
Setting
Invoke setting menu
Source
Select Visualizer input
signal
Resolution
Select resolution from
XGA, SXGA, WXGA,
720P,1080P ,800P and
1200P directly
OK
Move the cursor
Left,Right,Up,Down/Confir
m
Menu
Invoke menu
Zoom in/
Zoom
out
Increase and decrease
magnification
Snap
Capture a still image
Record
Record a video clip
Far/Near
Focus near or far
Freeze
Freeze the image, press
again to unfreeze
Playback
Re-display stored imaged
and videos
Projector
Power
Control the Projector On/ Off
Projector
Source
Select Projector input signal
Flip
V-Reverse the image
Rotate
Image rotation of
90°
,
180°
, 270°
- 5 -
Basic Preparations
1.
Place one hand firmly on the base of the visualizer, while carefully lifting up
the camera stand using the other hand.
2.
Open the arm lights and rotate the camera head until they are properly positioned.
- 6 -
Making Connections
●
Connect to the projector
Connect the PROJECTOR port to the projector's RGB IN port using the RGB cable.
You can also control a projector using the controls on the visualizer by connecting the
projector to the visualizer using a RS232 cable. Some projector models may require
a converter cable in addition to this standard RS232 cable to connect to the projector
control port, for the pin locations and shape of some projectors’ control port
connector may be different from the connector of a standard RS232 cable. Once the
visualizer
is connected to the projector, you can control the projector's power on, standby and
input selection by using the visualizer. (Aside from Hitachi projectors, the Code
Writing program that comes with the visualizer is required to access this function.)
- 7 -
●
Connect to a desktop computer
●
Connections for external control from the computer
- 8 -
Use the computer RS232 cable to make the connections displayed below to control
the visualizer from an external computer.
A USB connection enables the computer to capture still images and/or video
streams from the visualizer. Special software is required for this operation.
●
Connect power source
First connect the power cord to the 12V IN connector.
Indice
Altri manuali Qomo Macchina fotografica digitale
