Quantum PX500 Series Guida rapida
81-81351-01 C01, April 2006 1
Quantum PX500 Series
FC1202 Upgrade Instructions
Introduction 3
Fibre Channel Description........................................................................... 3
FC1202 Bridge Operation............................................................................. 3
Preparing for the FC1202 Installation 4
Required Upgrade Kits ................................................................................ 4
Required Equipment (Customer Supplied) .............................................. 4
Required Tools .............................................................................................. 4
FC1202 Upgrade Procedure 4
Preparing the Quantum PX500 Series Library ......................................... 5
Removing Tape Drive SCSI Jumper Cables.............................................. 6
Installing the FC1202 Bridge ....................................................................... 9
Installing the Ethernet Cables ................................................................... 13
Installing SCSI Jumper Cables .................................................................. 17
Configuring the FC1202 Bridge Software................................................ 19
Saving the Configuration File ................................................................... 25
Enabling Serverless Backup (Xcopy)........................................................ 27
Zoning the Ethernet Switch 29
Quantum PX500 Series FC1202 Upgrade Instructions
81-81351-01 C01
April 2006
Made in the USA.
Quantum Corporation provides this publication “as is” without warranty of any kind, either express or implied, including but not limited to
the implied warranties of merchantability or fitness for a particular purpose. Quantum Corporation may revise this publication from time to
time without notice.
COPYRIGHT STATEMENT
© Copyright 2006 by Quantum Corporation. All rights reserved.
Your right to copy this document is limited by copyright law. Making copies or adaptations without prior written authorization of Quantum
Corporation is prohibited by law and constitutes a punishable violation of the law.
TRADEMARK STATEMENT
Capacity on Demand (CoD), Crosslink Mechanism, DLT, DLTSage, DLTtape, Super DLTtape, Performance on Demand, (PoD), PRISM,
PRISM Storage Architecture logo, SiteCare, StackLink, StorageCare, SuperLoader, and ValueLoader are all trademarks of Quantum
Corporation. Quantum, the Quantum logo, and the DLTtape logo are all registered trademarks of Quantum Corporation.
Other trademarks may be mentioned herein which belong to other companies.
2
Quantum PX500 Series FC1202 Upgrade Instructions
81-81351-01 C01
April 2006
Introduction 3
Introduction 0
The Quantum PX500 Series automated tape libraries are controlled by a host
computer via a SCSI LVD bus using the SCSI-3 medium changer command
set.
The Quantum PX500 Series allows for easy conversion from the SCSI host
interface to a Fibre Channel host interface. This document describes
upgrading a standard PX500 library equipped with a SCSI host interface to a
Fibre Channel host interface using a FC1202 Upgrade kit.
Fibre Channel
Description 0Fibre Channel is a serial data transfer architecture for use with computers and
mass storage devices that is rapidly emerging to challenge SCSI as the
interface of choice for host-to-storage applications.
Fibre Channel advantages include:
• Connection distances with the Quantum FC1202 option up to 500 meters
• 1 GB/Sec, 2 GB/Sec, or autosense data transfer rates
• Supports up to 126 devices in a loop mode
• Supports 24-bit addressing for over 16 million devices in point-to-point
mode or fabric, when using a Fibre Channel switch or multiple Fibre
Channel switches.
• Operating system independence
• Interconnect flexibility
FC1202 Bridge
Operation 0Once a FC1202 bridge option is installed and tested, the library operates
exactly as a PX500 Series with a SCSI host interface. Operation of the library
via the operator control panel (OCP) is unchanged.
Quantum PX500 Series FC1202 Upgrade Instructions
81-81351-01 C01
April 2006
4 Preparing for the FC1202 Installation
Preparing for the FC1202 Installation 0
Before beginning the installation procedure, make sure that you have the
required upgrade kit and tools.
Required Upgrade Kits 0The FC1202 installation requires the following upgrade kit for every two tape
drives in a PX500 Series library (see table 1):
Table 1 FC1202 Upgrade
Kit PN PR-UU9CF-YF
Required Equipment
(Customer Supplied) 0A zonable Ethernet switch is required if multiple FC1202 Fibre Channel
bridges are installed in either a PX506 or PX510 library. If a single FC1202
Fibre Channel bridge is installed, an Ethernet switch is not required.
Required Tools 0The following tools are required to install the FC1202 bridge upgrade:
• #2 PHILLIPS® screwdriver
FC1202 Upgrade Procedure 0
The upgrade procedure is identical regardless of the number of FC1202s
installed except where noted. The upgrade procedure consists of the
following major steps:
•Preparing the Quantum PX500 Series Library
•Removing Tape Drive SCSI Jumper Cables
•Installing the FC1202 Bridge
•Installing the Ethernet Cables
•Installing SCSI Jumper Cables
Note: All part numbers are subject to change without notice.
Qty Description
1 FC1202 PWA
2 SCSI Cables
1Ethernetcable
1Terminator
1Quantum PX500 Series FC1202 Upgrade Instructions
Quantum PX500 Series FC1202 Upgrade Instructions
81-81351-01 C01
April 2006
FC1202 Upgrade Procedure 5
•Configuring the FC1202 Bridge Software
Preparing the
Quantum PX500
Series Library 0
To prepare the PX500 Series library:
1With the library turned on, press the Ops button on the OCP to access the
Operations screen (see figure 1).
Figure 1 Operations
Screen
2Select Library operations and press Enter.
3From the library operations menu, select Library on/offline and press Enter
to turn the library offline.
4Verify that the OCP display indicates “Offline” from the OCP screen.
5Turn off the power button located on the front of the library (see figure 2).
Figure 2 Turning On the
Library
Caution: Use appropriate ESD procedures when assembling and
installing the FC1202 option.
Enter
Power button
OCP
Quantum PX500 Series FC1202 Upgrade Instructions
81-81351-01 C01
April 2006
6 FC1202 Upgrade Procedure
Removing Tape Drive
SCSI Jumper Cables 0Each pair of tape drives within the library are connected via a SCSI jumper
cable. These cables must be removed prior to cabling the FC1202.
1Locate the SCSI jumper cables connecting each pair of tape drives in the
library and the host systems (see figure 3 for PX502, figure 4 for PX506,
and figure 5 for PX510). The tape drives are numbered 1 through 10
(depending on library model) starting in the top-left drive bay. Tape drive
1 is in the upper right-hand drive bay, tape drive 2 is in the upper left-
hand drive bay, and so forth. Refer to the following illustrations for exact
tape drive numbering.
Figure 3 PX502 Cabling
Configuration
Tape drive 2 Tape drive 1
SCSI
terminator
SCSI
jumpers
Host computer
Quantum PX500 Series FC1202 Upgrade Instructions
81-81351-01 C01
April 2006
FC1202 Upgrade Procedure 7
Figure 4 PX506 Cabling
Configuration
Host computer
Host computer
Host computer
SCSI
jumper
SCSI jumper
SCSI
terminators
SCSI jumper
Tape drive 2 Tape drive 1
Tape drive 4
Tape drive 6 Tape drive 5
Tape drive 3
Quantum PX500 Series FC1202 Upgrade Instructions
81-81351-01 C01
April 2006
8 FC1202 Upgrade Procedure
Figure 5 PX510 Cabling
Configuration
2Remove all SCSI jumper cables connecting each pair of tape drives and
the host systems and also all terminators.
Host computer
Host computer
Host computer
SCSI jumper
SCSI
terminators
SCSI
jumper
Host computer
Host computer
SCSI
terminators
SCSI
jumper
SCSI
jumper
Tape drive 2 Tape drive 1
Tape drive 4
Tape drive 6 Tape drive 5
Tape drive 3
Tape drive 8 Tape drive 7
Tape drive 10 Tape drive 9
SCSI
jumper
Quantum PX500 Series FC1202 Upgrade Instructions
81-81351-01 C01
April 2006
FC1202 Upgrade Procedure 9
Installing the FC1202
Bridge 0The number of FC1202 bridges required depends on the number of tape
drives installed in the library.
• 1 to 2 tape drives requires 1 FC1202
• 3 to 4 tape drives requires 2 FC1202 bridges (PX506 and PX510 only)
• 5 to 6 tape drives requires 3 FC1202 bridges (PX506 and PX510 only)
• 7 to 8 tape drives requires 4 FC1202 bridges (PX510 only)
• 9 to 10 tape drives requires 5 FC1202 bridges (PX510 only)
To install the FC1202 bridge:
1Loosen the two PHILLIPS screws securing the blank off plate(s) to the
CPCI card cage and expose the number of slots needed for the FC1202
installation (one blank off plate per FC1202).
2With the SCSI ports located to your right as you face the back of the
library, slide the first FC1202 into the slot of the card cage (see figure 6 for
PX502, figure 7 for PX506, and figure 8 for PX510).
Figure 6 Installing a
FC1202 Bridge (PX502)
Note: Start the FC1202 installation in slot 1 of the CPCI card cage
(PX506 and PX510 only).
Blank off plate
Screws
Card cage
FC1202
Quantum PX500 Series FC1202 Upgrade Instructions
81-81351-01 C01
April 2006
10 FC1202 Upgrade Procedure
Figure 7 Installing a
FC1202 Bridge (PX506) Blank off plate
Screws
Card cage
FC1202
Slot 1
Altri manuali per PX500 Series
6
Questo manuale è adatto per i seguenti modelli
4
Indice
Altri manuali Quantum Magazzinaggio
Quantum
Quantum QXS-448 Manuale utente
Quantum
Quantum LTO 2U Foglio di istruzioni
Quantum
Quantum Scalar 50 Manuale utente
Quantum
Quantum A-Series FTP Manuale utente
Quantum
Quantum Scalar 50 Manuale utente
Quantum
Quantum Scalar 218FC Manuale utente
Quantum
Quantum DLTtape DLT1 Manuale utente
Quantum
Quantum DXi4601 Manuale utente
Quantum
Quantum StorNext QM1200 Manuale utente
Quantum
Quantum Scalar i6000 Manuale utente
Quantum
Quantum Atlas V Manuale utente
Quantum
Quantum Scalar i500 Manuale utente
Quantum
Quantum StorNext QD7000 Manuale utente
Quantum
Quantum Tape Drives A-Series Manuale utente
Quantum
Quantum Scalar i40 Manuale utente
Quantum
Quantum Scalar i500 Manuale utente
Quantum
Quantum DXi6902 Manuale dell'operatore
Quantum
Quantum Scalar i2000 Manuale utente
Quantum
Quantum StorNext QD6000 Manuale utente
Quantum
Quantum LTO-3 Manuale utente
