Quarkpro FS-3000D Manuale utente
www.quarkpro.com
USER´S MANUAL
MANUAL DE USUARIO
3 DMX CHANNELS MODES
PREPROGRAMED SPECIAL EFFECTS
CONTINUOUS BLINDER EFFECT
SAFETY INFORMATION
To guard against electric shock
• Disconnect the xture from AC power and allow the ash capacitor to discharge
for 1 minute before changing the lamp or fuse, and when not in use.
• Do not remove the rear cover: there are no user-serviceable parts inside.
• Always ground (earth) the xture electrically.
• Do not expose the xture to rain or moisture.
• Replace the lamp only as described or have it replaced by a Strobe service technician.
To guard against UV radiation, burns, and re
• Never operate the xture with the front glass open, missing or damaged.
• Do not stare directly into the light. Never look at an exposed lamp while it is lit.
• Replace the lamp when it becomes defective or worn out.
• When replacing the lamp, allow the xture to cool for at least 10 minutes before
opening the xture or removing the lamp.
• Never attempt to bypass the fuse. Always replace defective fuses with ones of the
specied type and rating.
• Keep all combustible materials (for example fabric, wood, paper) at least 0.5
meters (20 inches) away from the xture. Keep ammable materials well away
from the xture.
• Do not illuminate surfaces within 1 meter (39 inches) of the xture.
• Provide a minimum clearance of 0.1 meters (4 inches) around air vents.
• Never place lters or other materials over the front glass cover.
• The exterior of the xture can reach temperatures up to 120° C (248° F). Allow
the xture to cool for at least 15 minutes before handling.
• Do not operate the xture if the ambient air temperature (Ta) exceeds 40° C (104° F).
Note: Avoid extended periods of continuous ashing, particularly at frequencies of 10
to 20 ashes per second
1EN
2EN
TO INSTALL THE MOUNTING BRACKET
1.- Place the xture face down on a table
2.- Place a plastic washer on each mounting bracket stud
3.- Place one end of the bracket on one of the mounting studs. Bend the other end of
the mounting bracket open slightly and work it onto the opposite stud
4.- Place a hand knob on each stud. Tighten both hand knobs to lock the mounting
bracket in place
DMX OPERATION
DMX connection
The FS-3000D provides both 3-pin and 5-pin XLR sockets for data connection. The
pin-out on all sockets is pin 1 to shield, pin 2 to cold (-), and pin 3 to hot (+). There is no
connection to pins 4 and 5. The sockets are wired in parallel: both inputs connect to
both outputs. For reliable data transmission use one input and one output!
DMX link
1. Connect the DMX data input from the controller to the FS-3000D´s 3-pin or 5-pin
input (male) socket.
2. You can connect up to 31 additional xtures output-to-input.
3. Insert a termination plug in the output of the last xture on the link.
3EN
DATA CONNECTION TIPS
• Use shielded twisted-pair cable designed for RS-485 devices: standard
microphone cable cannot transmit control data reliably over long runs. 24 AWG
cable is suitable for runs up to 300 meters (1000 ft.). Use heavier gauge cable
and/or an amplier for longer runs.
• Never use both outputs to split the link. To split the serial link into branches use a
signal splitter.
• Do not overload the link. Up to 32 devices may be connected on a serial link.
• Terminate the link by installing a termination plug in the output socket of the last
xture. The termination plug, which is a male XLR plug with a 120 ohm, 0.25 watt
resistor soldered between pins 2 and 3, “soaks up” the control signal so it does not
reect and cause interference.
DMX CONTROL MODES
The DMX control options are selected on the Mode DIP switch
1 Channel DMX mode allows you to strobe from 0 ashes
per second to the maximum ash rate and trigger the blinder
effect from the controller. To select 1ch DMX operation, set pin 5
of the mode DIP switch to ON; set pins 1 to 4 to OFF
3 Channel DMX mode provides control of ash intensity, ash duration
and ash rate for more advanced control than 1 channel mode.
To select 3 channel DMX operation, set pins 1 to 5 of the mode DIP switch
to OFF.
4 Channel DMX mode provides six special effects in addition to
ash intensity, duration and rate control. To select this 4 ch DMX
operation, set pins 1,2,3 and 5 to OFF,set pin 4 to ON
CONTROL ADDRESS
The control address, also known as the start channel, is the rst channel used to receive
instructions from the controller. The adress may be any channel from to 1 to 511 and is
set on the address DIP switch.
The FS-3000D uses 1,3 or 4 channels depending on the control mode. For independent
control, each xture must be assigned its own address and nonoverlapping control
channels. Two or more FS-3000D may share the same address if individual control is not
required.
4EN
To set the DMX address
1.- Select an address for the xture on your controller. Look up the DIP switch setting for
the address in the table below
2.- Set pins 1 through 9 ON (1) or OFF (0) as listed in the table. Set pin 10 to OFF
Find the address in the table. Read the settings for pins 1-5 to the left and read the
settings for pins 6-9 above the address. “0” means OFF and “1” means ON.
Pin 10 is always OFF for DMX operation.
5EN
Channel 2 Channel 14 Channel 46 Channel 100
DMX CONTROL SUMMARY
INTENSITY
Flash intensity can be set from minimum (blackout) to maximum on channel 1 in the 3- and
4-channel DMX modes. Intensity is maximum in 1-channel DMX mode.
DURATION
Flash duration can be set from 0 to 650 ms on 50 Hz power supplies, or 0 to 530ms on 60 Hz
power supplies, on channel 2 in the 3- and 4-channel DMX modes. Flash duration is xed in
1-channel DMX mode.
RATE
Flash rate can be set from 0 ashes per second to 25 ashes per second Hz on 50Hz power
supplies, or from 0 to 30 ashes per second on 60 Hz power supplies, on channel 3 in the
3-and 4-channel DMX modes. Flash rate is also controllable in 1-channel DMX mode.
PROGRAMMED EFFECTS
Six programmed effects are available on channel 4 in the 4-channel DMX mode only. The
effects may be altered using the intensity, duration, and rate controls.
• Ramp up: Light gradually increases in intensity, then blacks out.
• Ramp down: Light ashes to full intensity, then gradually fades.
• Ramp up-down: Light gradually increases and decreases.
• Random ash: Light ashes randomly with variable rate and intensity. Multiple units ash
independently of each other.
• Lightning: The ashes simulate lightning. Duration is not adjustable.
• Spikes: The lamp remains dimly illuminated between ashes. Set ash intensity, duration, and
rate as normal.
BLINDER EFFECT
The blinder effect, in which the light remains on for an extended period, is available in all DMX
modes. In the 3- and 4-channel modes, the effect is achieved whenever the combination of
ash duration and rate prevents pauses between ashes. For example, the blinder effect can
be achieved with a ash duration of 0.25 seconds (250 ms) and a ash rate of 4 ashes per
second, or a ash duration of 0.05 seconds (50 ms) and a ash rate of 20 ashes per second. In
3- and 4-channel DMX mode, the intensity of the blinder effect is controllable on channel 1.
Lamp power is electronically regulated to prevent the lamp from overheating. The intensity
falls as power is reduced.
6EN
SINGLE FLASH
To trigger single ashes, start with the intensity and ash rate at 0 and then set an
intensity on channel 1. When the value of channel 1 changes, the light will ash
once with the programmed intensity, duration, and effect.
STAND ALONE OPERATION
STAND ALONE FLASH RATE
To program stand alone execution
1.- Apply power to the xture
2.- Set pin1 of the mode DIP switch to ON. Set pins 2 -5 to OFF. Set pin 6 to ON for low
power operation or to OFF for high power operation.
3.- Select either a ash rate or the blinder effect. You set a ash rate by setting a value
from 1 to 255 with pins 1-8 of the address DIP switch. The value required to achieve a
desired ash rate can be calculated as follows.
To achieve a ash rate of 10 ashes per second on a 50 Hz AC power supply, for example,
the DIP value is 251. To select the blinder effect instead, set pin 9 to ON.
4. Set DIP switch pin 10 to OFF for normally off operation, or to ON for normally on
operation.
DIP value = 261 - 2 x AC frequency
Flash rate
7EN
DMX PROTOCOLS
1 CHANNEL DMX MODE
Channel Value Percent Function
1 0-5 0-1 Blackout
6-249 2-98 Flash rate,slow or fast
250-255 98-100 Continuous “Blinder” effect
3 AND 4 CHANNEL DMX MODES
Value Percent Function
Channel 1 0-5 0-1 Flash intensity
6-255 2-100 Blackout
Minimum to maximum
Channel 2 0-255 0-100 Flash Duration
0-650ms 50Hz AC
0-530ms 60Hz AC
Channel 3 0-5 0-1 Flash Rate
6-255 2-100 No ash (single ash with ch.1)
0.5-25Hz 50Hz AC
0.6-30Hz 60Hz AC
Note: Enable channel 4 with mode DIP switch no. 4 on
Channel 4 Special Eects
0-5 0-1 No effect
6-42 2-16 Ramp up
43-85 16-33 Ramp down
86-128 33-50 Ramp up-down
129-171 50-67 Random
172-214 67-84 Lightning
215-255 84-100 Spikes
DATA CONNECTION TIPS
• Use shielded twisted-pair cable designed for RS-485 devices: standard
microphone cable cannot transmit control data reliably over long runs. 24 AWG
cable is suitable for runs up to 300 meters (1000 ft.). Use heavier gauge cable
and/or an amplier for longer runs.
• Never use both outputs to split the link. To split the serial link into branches use a
signal splitter.
• Do not overload the link. Up to 32 devices may be connected on a serial link.
• Terminate the link by installing a termination plug in the output socket of the last
xture. The termination plug, which is a male XLR plug with a 120 ohm, 0.25 watt
resistor soldered between pins 2 and 3, “soaks up” the control signal so it does not
reect and cause interference.
DMX CONTROL MODES
The DMX control options are selected on the Mode DIP switch
1 Channel DMX mode allows you to strobe from 0 ashes
per second to the maximum ash rate and trigger the blinder
effect from the controller. To select 1ch DMX operation, set pin 5
of the mode DIP switch to ON; set pins 1 to 4 to OFF
3 Channel DMX mode provides control of ash intensity, ash duration
and ash rate for more advanced control than 1 channel mode.
To select 3 channel DMX operation, set pins 1 to 5 of the mode DIP switch
to OFF.
4 Channel DMX mode provides six special effects in addition to
ash intensity, duration and rate control. To select this 4 ch DMX
operation, set pins 1,2,3 and 5 to OFF,set pin 4 to ON
CONTROL ADDRESS
The control address, also known as the start channel, is the rst channel used to receive
instructions from the controller. The adress may be any channel from to 1 to 511 and is
set on the address DIP switch.
The FS-3000D uses 1,3 or 4 channels depending on the control mode. For independent
control, each xture must be assigned its own address and nonoverlapping control
channels. Two or more FS-3000D may share the same address if individual control is not
required.
8ES
INFORMACIÓN SOBRE SEGURIDAD
Para protegerse de las descargas eléctricas
• Desconecte el aparato de la red eléctrica y permita que el condensador de destellos
descargue durante 1 minuto antes de cambiar la lámpara o fusible.
• No quite la cubierta posterior: no hay piezas que el usuario pueda reparar.
• Siempre conecte a tierra (masa) el aparato eléctrico .
• No exponer el aparato a la lluvia ni a la humedad .
• Cambie la lámpara sólo como se describe o solicite su remplazo a un técnico .
Para protegerse contra la radiación UV , quemaduras y fuego
• Nunca haga funcionar el aparato con el cristal frontal abierto o dañado .
• No mire directamente a la luz. Nunca mire una lámpara mientras esté encendida.
• Cambie la lámpara cuando esté defectuosa o desgastada .
• Al cambiar la lámpara, deje enfriar el aparato durante al menos 10 minutos antes
de abrirlo.
• Nunca intente anular el fusible. Sustituya siempre los fusibles defectuosos por otros del
mismo tipo y características.
• Mantener todos los materiales combustibles ( p.ej. tejidos , madera, papel) al menos 0,5
metros de distancia del aparato . Mantenga los materiales inamables lejos del aparato.
• No iluminar supercies de menos de 1 metro del dispositivo .
• Dejar una distancia mínima de 0,1 metros de las salidas de ventilación del aparato .
• No colocar nunca ltros u otros materiales sobre la cubierta frontal de vidrio .
• El exterior del aparato puede alcanzar temperaturas de hasta 120 ° C ( 248 ° F). Dejar
que el aparato se enfrie al menos 15 minutos antes de su manipulación.
• No utilice el aparato si la temperatura ambiente excede los 40 ° C
Nota: Evitar largos períodos de parpadeo continuo , sobre todo en frecuencias de 10
a 20 destellos por segundo
9ES
PARA INSTALAR EL SOPORTE DE MONTAJE
1.- Coloque el dispositivo sobre una mesa
2.- Coloque una arandela de plástico en cada perno
3.- Coloque un extremo de la abrazadera en uno de los pernos de montaje
4.- Coloque las perillas de ajuste en cada perno Apriete las dos perillas de ajuste para
bloquear el soporte de montaje
FUNCIONAMIENTO DMX
Conexión DMX
El FS-3000D tiene conectores XLR de 3 pines y 5 pines para la conexión DMX. Los
enchufes están conectados en paralelo: ambas entradas están conectadas a ambas
salidas.
Enlace DMX
1. Conecte la entrada DMX desde el controlador hasta la entrada de 3 pines o 5 pines del
FS-3000D (macho).
2. Conecte hasta 31 dispositivos adicionales
3. Inserte un terminal en la salida del último dispositivo de la línea.
Indice
Lingue:
Altri manuali Quarkpro Attrezzatura per DJ
