RAB Lighting BLED5 Square Manuale utente

BLED5 INSTALLATION INSTRUCTIONS

IMPORTANT

READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.

RAB xtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper

grounding is required for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE

INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT

AND THE HAZARDS INVOLVED. WARNING: Make certain power is OFF before installing or maintaining

xture. No user servicable parts inside.

Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.

Call the Marketing Department at 888-RAB-1000, or email: marketing@rabweb.com

LOCATION

1. The Bollard should be mounted to a rm level

surface.

2. Anchor bolts may be used in new concrete

installations. Use the template provided.

3. For all other applications use anchors suitable for the

mounting surface.

ANCHOR BOLTS INSTALLATION

CAUTION: Install according to all applicable local codes.

1. Install two Anchor Bolts in concrete foundation (by

others) using the template provided. Mounting Plate

may also be used as the template. Anchor Bolts

should protrude no more than 3”.

Concrete

Conduit

Anchor

Bolts

Mounting

Plate

MOUNTING PLATE

Assemble xture(s) to bollard before mounting the Bol-

lard to the Mounting Plate.

1. Place the Mounting Plate over Anchor Bolts.

2. Use four Leveling Screws or shims to level the

Mounting Plate.

3. Tighten assembly using the washers, lockwashers

and nuts provided.

4. Make sure supply leads extend far enough to make

xture connections.

5. Slide Gasket down around the bottom of the

Mounting Plate.

6. Use the four screws to mount the Bollard to the

Mounting Plate. Tighten securely.

Mounting

Plate

Anchor

Bolts

Gasket

Leveling

Screws

Mounting

Screws

Bollard

BLED5 Square BLEDR5 Round BLED2X5 Square BLEDR2X5 Round

BLED5 INSTALLATION INSTRUCTIONS

MOUNTING fIXTURES

For BLED5 & BLEDR5 the window is available on one side of Bollard. Secure Bollard before installing the housing.

1. Loosen Housing Screws and remove Mounting Plate. Screws will remain in place with O-ring retaining gaskets.

Fixture may hang from the tether while installing.

2. Place Bollard Gasket and Mounting Plate over recessed box.

3. Attach Mounting Plate with supplied Mounting Plate Screws.

4. Pull supply wires from box through mounting plate and wire xture as shown in the wiring section.

5. Check Housing Gasket. It should remain rmly around the inside of the Housing.

6. Align Housing to Mounting Plate.

7. Make sure all gaskets are properly seated. Tighten Housing Screws.

8. Secure the Cap Gasket and tighten the Bollard Cap with supplied screws.

Bollard

Housing

screws

Bollard

Cap

Gasket

Housing Mounting

Plate

Bollard

Cap

Gasket

Bollard

Gasket

BLED5 INSTALLATION INSTRUCTIONS

BLED5-IN-0612

MOUNTING fIXTURES

For BLED2x5 & BLEDR2x5, cutouts are provided on both sides of Bollard. Secure Bollard before installing the

housings.

1. Loosen Housing Screws and remove Mounting Plate. Screws will remain in place with O-ring retaining gaskets.

Fixture may hang from the tether while installing.

2. Place Bollard Gasket and Mounting Plate over cut out on Bollard.

3. Attach Mounting Plate with supplied mounting plate screws.

4. Pull supply wires from bollard through mounting plate and wire xture as shown in the wiring section.

5. Check Housing Gasket. It should remain rmly around the inside of the Housing.

6. Align Housing to Mounting Plate.

7. Make sure all gaskets are properly seated. Tighten Housing Screws.

8. Follow same steps for second xture.

9. Secure the Cap Gasket and tighten the Bollard Cap with provided screws.

Bollard

Housing

screws

Bollard

Cap

Gasket

Housing

Gaskets

Mounting

Plate

Housing-

Screws

Bollard

Cap

Gasket

Bollard

Mounting

Plate

Bollard

Gasket

Bollard

Gasket

BLED5 INSTALLATION INSTRUCTIONS

ACCESSORIES

Bollard base: BOLBASE

Bollard base Retro kit: BOLBASE RETRO

Sufx “Y” = Warm 3000K LED

Sufx “N” = Neutral 4000K LED,

WIRING

Universal driver permits 120V to 240V, 50 or 60Hz.

1. Connect the black xture lead to the (+) LINE

supply lead.

2. Connect the white xture lead to the (-) COMMON

supply lead.

3. Connect the bare copper Ground wire from xture to

supply ground.

LIGHT

FIXTURE

(+)LINE BLACK

(-)COMMON WHITE

GROUND GROUND

CLEANING & MAINTENANCE

CAUTION: Be sure xture temperature is cool

enough to touch. Do not clean or maintain while

xture is energized.

1. Clean glass lens with non-abrasive glass cleaning

solution

2. Do not open xture to clean the LED.

TROUBLESHOOTING

1. Check that the line voltage at xture is correct. Refer

to wiring directions.

2. Is the xture grounded properly?

3. Is the photocell is functioning properly (if used)?

SLED Round: US pat. D612,974, CA Pat. pending,

CN Pat. pending

SLED Square:.US pat. D612,975, CA Pat. pending,

CN Pat. pending

Note: These instructions do not cover all details or variations

in equipment nor do they provide for every possible situation

during installation, operation or maintenance.

BLED5 Cool LED Square Steplight BLEDR5 Cool LED Round Steplight

BLED5 INSTALLATION INSTRUCTIONS

BLED5Y Warm LED Square Steplight BLEDR5Y Warm LED Round Steplight

BLED5N Neutral LED Square Steplight BLEDR5N Neutral LED Round Steplight

BLED5 INSTALLATION INSTRUCTIONS

ANCHOR BOLT TEMPLATE fOR BLED BOLLARD

Conrm dimensions before using as a template. If possible use the actual mounting plate as your template.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali RAB Lighting Apparecchio di illuminazione

RAB Lighting

RAB Lighting ALED 52W Manuale utente

RAB Lighting

RAB Lighting GOOSE Manuale utente

RAB Lighting

RAB Lighting floodinator Manuale utente

RAB Lighting

RAB Lighting WP1LED Manuale utente

RAB Lighting

RAB Lighting DLED4R Manuale utente

RAB Lighting

RAB Lighting VAN1LED Manuale utente

RAB Lighting

RAB Lighting Mini Sensor Manuale utente

RAB Lighting

RAB Lighting Yard Blaster Series Manuale utente

RAB Lighting

RAB Lighting FALCOR 80W Manuale utente

RAB Lighting

RAB Lighting future flood Manuale utente

RAB Lighting

RAB Lighting HSLED Manuale utente

RAB Lighting

RAB Lighting MASI Manuale utente

RAB Lighting

RAB Lighting WPLED 78W series Manuale utente

RAB Lighting

RAB Lighting VX Series Manuale utente

RAB Lighting

RAB Lighting FXLED Manuale utente

RAB Lighting

RAB Lighting GNLED13Y Manuale utente

RAB Lighting

RAB Lighting CANVAS78 Manuale utente

RAB Lighting

RAB Lighting WPLEDC104 Manuale utente

RAB Lighting

RAB Lighting YBLED 3 pin PCT Manuale utente

RAB Lighting

RAB Lighting MEGAFLOOD Manuale utente

Manuali Apparecchio di illuminazione popolari di altre marche

Emos

Emos CLASSIC ZY1431T Manuale utente

Westinghouse

Westinghouse Outdoor Lighting Fixture Manuale utente

Hedler

Hedler C 12 silent Manuale utente

Blizzard Lighting

Blizzard Lighting Puck: CSI Manuale utente

Energetic Lighting

Energetic Lighting ELYSL-5004 Series Manuale utente

Lightmaxx

Lightmaxx Shaft 5R Manuale utente

Triarch

Triarch 31083 Manuale utente

Philips

Philips 32614 Series Manuale utente

IKEA

IKEA TIVED Manuale utente

Lightolier

Lightolier LP200 Manuale utente

Chauvet Professional

Chauvet Professional ROGUE R1 BEAM WASH Manuale utente

Martin

Martin MAC 250 Krypton Manuale utente

Cooper Lighting

Cooper Lighting Halo L3232E Manuale utente

Stageline

Stageline ODW-2410RGBW Manuale utente

Light Sky

Light Sky Tornado Series Manuale utente

Lightolier

Lightolier Paralyte 2424 PLA2G9LS26U Manuale utente

Lightolier

Lightolier Lytespan 83ED17S Manuale utente

Lightolier

Lightolier Calculite CS8226 Manuale utente