Rack Solutions 4Post Manuale utente
4Post and 2Post Rails for
Dell PowerEdge R210
Installation Instructions
Kit P/N: 109-1953
109-1956
4Post
Page 2
2Post Center
Page 4
2Post Flush
Page 6
Page 2
4Post Installation Instructions
Kit Contents
Step 1. Install cage nuts as shown at the rear of a square hole rack: (4) 12-24 black
cage nuts.
Step 2a. The rail kit is pre-set for rack depths of 15.00” to 19.75” [381mm to 501mm]: If
your rack is greater than 19.75” [501mm] deep, move the hardware attaching the
Rear Slider brackets to get the needed adjustment range. Moving the hardware
attaching the Rear Slider can achieve any depth from 15” to 23.5” [381mm to
596mm].
Rear of Rack
(4) 12-24 black cage nuts
Pre-Set Range 15.00" to 19.75"
[381mm to 501mm]
Kit Contents:
(1) Right Rail Assembly
(1) Left Rail Assembly
Mounting Hardware:
(2) Hook Plates (Left & Right)
(2) Angle Bracket
(4) 8-32 x .500 Pan Head
(4) 8-32 x .375 Flat Head
(4) 8-32 Keps Nut
Rack Mount 4x:
(4) 10-32 x .500 Pan Head
(4) 12-24 x .500 Pan Head
(4) 12-24 Square Nut
(4) 12-24 Cage Nut
Step 2b.For rack depths greater than 20.00” [508mm]: Attach Angle Bracket to both rails
using supplied hardware as shown.
Angle Bracket
4Post Installation Instructions
Page 3
Step 3. Attach the rails to the rack:
- Attach the front and Rear of the rails to the 4Post rack using (4) supplied Pan
Head Screws on each side
- Tighten the front and rear Pan Head Screws on the right side rail. Leave the
front and rear Pan Head Screws on the left side rail slightly loose.
Step 4. Install the equipment: Slide the equipment onto the rails so the Equipment
Mounting Lugs on each side slide into the Rail Slot on both sides. Slide the
equipment all the way in. Tighten the (2) Pan Head Screws on the back of the
left slide rail. Slide the equipment out about 8 inches and tighten the (2) Pan
Head Screws on the front of the left slide rail.
Note: When tightening the loose rails, support the bottom of the server to ensure proper
rail adjustment.
Front Left
(4) 8-32 Pan Head Screws
(4) 10-32 or 12-24
Pan Head Screws
Front Right
Rear
Rear Bracket
Rail Slot
Equipment Mounting Lugs
(2) on each side
Page 4
2Post Center Installation Instructions
Step 1. Installing Rail Kit: Installing this rail kit in a 2Post center rack requires the
NLWZLWKQRFKDQJHWRWKHSUHDVVHPEOHGUDLOFRQ¿JXUDWLRQ
Step 2. Attach the rails to the rack:
- Attach the 2Post Adapter Bracket per the "2 Post Racking System"
Instructions.
- Attach the Front and Rear of the rails to the 2Post rack using (4) supplied Pan
Head Screws on each side.
- Tighten the front and rear Pan Head Screws on the right side rail. Leave the
front and rear Pan Head Screws on the left side rail slightly loose.
Front Left Front Right
Rear
Pre-Set Range 15.00" to 19.75"
[381mm to 501mm]
(4) 8-32 Pan Head Screws
(4) 10-32 or 12-24
Pan Head Screws
2Post Center Installation Instructions
Page 5
Step 3. Install the equipment: Slide the equipment onto the rails so the Equipment
Mounting Lugs on each side slide into the Rail Slot on both sides. Slide the
equipment all the way in. Tighten the (2) Pan Head Screws on the back of the
left slide rail. Slide the equipment out about 8 inches and tighten the (2) Pan
Head Screws on the front of the left slide rail.
Note: When tightening the loose rails, support the bottom of the server to ensure proper
rail adjustment.
Equipment Mounting Lugs
(2) on each side
Rail Slot
Page 6
2Post Flush Installation Instructions
Step 1. Install Rails:,QVWDOOLQJWKLVUDLONLWLQD3RVWÀXVKUDFNUHTXLUHVDFKDQJHWRWKH
SUHDVVHPEOHGUDLOFRQ¿JXUDWLRQDVIROORZV5HYHUVHWKHUHDUVOLGHUVRWKDWWKH
ÀDQJHLVWRZDUGWKHIURQW1RWHWKLVZLOOUHTXLUHD´ZUHQFKRUUDWFKHW
Rack Mount
Flanges Range 3" to 6"
[76mm to 152mm]
Step 2. Attach the rails to the rack:
- Attach the Front and Rear of the rails to the 2Post rack using (4) supplied Pan
Head Screws on each side.
- Tighten the front and rear Pan Head Screws on the right side rail. Leave the
front and rear Pan Head Screws on the left side rail slightly loose.
Front Left Front and
Rear Right
(4) 8-32 Pan Head Screws (4) 10-32 or 12-24
Pan Head Screws
Hook
Plate Hook Plate
Pre-Set Range 15.00" to 19.75"
[381mm to 501mm]
2Post Flush Installation Instructions
Page 7
Equipment Mounting
Lugs (2) on each side
Step 3. Install the equipment: Slide the equipment onto the rails so the Equipment
Mounting Lugs on each side slide into the Rail Slot on both sides. Slide the
equipment all the way in. Tighten the (2) screws on the back of the left slide rail.
Slide the equipment out about 8 inches and tighten the (2) screws on the front of
the left slide rail.
Note: When tightening the loose rails, support the bottom of the server to ensure proper
rail adjustment.
Warranty Statement
Innovation First, Inc. warrants our products against defects in material and workmanship for a
period of one (1) year from the date of purchase. Innovation First, Inc. liability shall be limited to
repairing or replacing, at our option, any defective product.
19561953
Questo manuale è adatto per i seguenti modelli
4
Indice
Altri manuali Rack Solutions Rack e supporto
Rack Solutions
Rack Solutions 124-2247 Manuale utente
Rack Solutions
Rack Solutions 1USHL-003 Manuale utente
Rack Solutions
Rack Solutions 104-1965 Manuale utente
Rack Solutions
Rack Solutions RACK-117-MOBILE KIT Manuale utente
Rack Solutions
Rack Solutions 1UKYB-126 Manuale utente
Rack Solutions
Rack Solutions VEX 111-6330 Manuale utente
Rack Solutions
Rack Solutions WALL-KYB-001 Manuale utente
Rack Solutions
Rack Solutions 104-2323 Manuale utente
Rack Solutions
Rack Solutions 122-4818 Manuale utente
Rack Solutions
Rack Solutions 5U Manuale utente
Rack Solutions
Rack Solutions 111-1731 Manuale utente
Rack Solutions
Rack Solutions 105-2670 Manuale utente
Rack Solutions
Rack Solutions 104-2324 Manuale utente
Rack Solutions
Rack Solutions 104-2411 Manuale utente
Rack Solutions
Rack Solutions 104-2109 Manuale utente
Rack Solutions
Rack Solutions 4UKIT-003BLK Manuale utente
Rack Solutions
Rack Solutions Wall-Mount-PC Manuale utente
Rack Solutions
Rack Solutions 2UKVM-125 Manuale utente
Rack Solutions
Rack Solutions 122-3491 Manuale utente
Rack Solutions
Rack Solutions FORZA DESIGNS Elite Controller Wall Mount Manuale utente
