Radial Engineering StageBug SB-48 Manuale utente

Circuit type: Non-radiating phantom power supply

Number of channels: 2

XLR connectors: AES standard pin-1 Ground, pin-2 (+),

pin-3 (-)

Phantom output: Switchable +48 / +12 volts DC

Power supply: 15VDC / 400mA external supply

included

www.radialeng.com

TruetotheMusic

Radial Engineering Ltd.

®TruetotheMusic

SB-48

POWERBAR

Radial Engineering Ltd. SB-48®Phantom Supply SB-48®Phantom Supply

FEATURES

1. XLR-F INPUTS: Usedto connect the mic signal to the StageBug

SB-48.Phantom power isgenerated inside the SB-48 and injected

into the mic capsule via the F-XLR connectors and mic cable.

2. POWER INPUT AND LED: The power jack accepts Radial’s

15VDC/400mApoweradapter.TheLEDilluminates whenthe power

supply is connected and the SB-48 is active.

3. CABLE CLAMP: Usedto lock downthe power supplycable and

prevent accidental disconnection.

4. XLR-M OUTPUTS: Usedto connect the mic signal to the mixing

console or preamp. Equipped to block other sources of phantom

power and prevent over-powering your condenser mic or active

direct box.

5. +12/48V SWITCH: Used to change the phantom supply from

the standard +48 volts to +12 volts for speciality microphones.

6. FULL-BOTTOM NO-SLIP PAD: Thisprovideselectrical isolation

and plenty of ‘stay-put’ friction to keep the SB-48 in one place. RADIAL ENGINEERING 3 YEAR TRANSFERABLE LIMITED

WARRANTY

RADIALENGINEERINGLTD.(“Radial”)warrantsthisproducttobefree fromdefectsinmaterial

and workmanship and will remedy any such defects free of charge according to the terms of

this warranty. Radial will repair or replace (at its option) any defective component(s) of this

product(excluding ﬁnish and wear and tear oncomponents under normal use) for a periodof

three (3) years from the original date of purchase. In the event that a particular product is no

longeravailable,Radialreserves theright toreplacetheproductwithasimilar productofequal

orgreater value. In the unlikely event thatadefect is uncovered, please call 604-942-1001 or

email [email protected] to obtain an RA number (ReturnAuthorization number) before

the3year warranty period expires. The product must be returned prepaid intheoriginal ship-

pingcontainer (or equivalent) to Radial or toanauthorized Radial repair center and youmust

assumetheriskof lossor damage.Acopyoftheoriginal invoiceshowingdateofpurchaseand

thedealer name mustaccompanyany requestforworkto beperformedunderthis limitedand

transferable warranty. This warranty shall not apply if the product has been damaged due to

abuse, misuse, misapplication, accident or as a result of service or modiﬁcation by any other

than an authorized Radial repair center.

THEREARENOEXPRESSEDWARRANTIESOTHERTHANTHOSEONTHEFACEHEREOF

AND DESCRIBED ABOVE. NO WARRANTIES WHETHER EXPRESSED OR IMPLIED,

INCLUDINGBUTNOTLIMITED TO,ANY IMPLIED WARRANTIES OF MERCHANTABILITY

ORFITNESSFORAPARTICULARPURPOSESHALLEXTENDBEYONDTHERESPECTIVE

WARRANTY PERIOD DESCRIBEDABOVE OF THREE YEARS. RADIAL SHALL NOT BE

RESPONSIBLEORLIABLEFORANYSPECIAL,INCIDENTALORCONSEQUENTIALDAM-

AGESOR LOSSARISING FROMTHEUSEOF THISPRODUCT. THIS WARRANTYGIVES

YOUSPECIFICLEGALRIGHTS,ANDYOUMAYALSOHAVEOTHERRIGHTS,WHICHMAY

VARYDEPENDINGONWHEREYOULIVEANDWHERETHEPRODUCTWASPURCHASED.

StageBug SB-48™User Guide - Part# R870 1221 00

Speciﬁcations and appearance are subject to change without notice.

Radial Engineering Ltd.

1588 Kebet Way, Port Coquitlam BC V3C 5M5

tel: 604-942-1001 • fax: 604-942-1010

[email protected] • www.radialeng.com

Stagebug SB-48 SPECIFICATIONS

USERGUIDE

INTRODUCTION

Thank you and congratulations on your purchase of the Radial

StageBug SB-48 dual phantom power supply. We have purposely

written this manual to be short, as most users will likely be familiar

with the use of phantom power. We do suggest that you take a mo-

ment to read through this document to familiarize yourself with the

features that are built into the SB-48. For more detailed information,

please visit the FAQ section on the Radial website. This is where we

post questions and answers that come from users after the product

is released. If you do not ﬁnd an answer, we invite you to send us an

email at [email protected] and we will do our best to answer your

query in short order.

The StageBug SB-48 is a two channel phantom power supply de-

signedtoprovide condensermicrophonesand active directboxes with

12 or 48 volts of regulated power. The SB-48 can supply one or two

phantom powered devices and allows their use with audio systems

that do not supply phantom power on their own.

The SB-48 features XLR inputs and outputs wired to the AES stan-

dard,an LED powerindicator andcomes complete withpower supply.

An integrated lock-down clamp for the power supply cable protects

against accidental disconnection.To address speciality microphones

that require 12 volts, a recessed ‘set & forget’ switch reduces the

voltage output.

CONNECTION

Before connecting the StageBug SB-48 make sure the sound sys-

tem is turned off and all levels are set to zero. Do not connect the

powersupply until all connections to and from the SB-48 have been

made. This will avoid loud transients that could cause damage to

equipment downstream such as loudspeakers and tweeters. After

use, remember to turn off the PA system before you disconnect the

SB-48’s power supply and the mic lines.

Using balanced XLR mic cables, connect the output of a condenser

microphone or active direct box to the XLR-F input. Next, connect

the XLR-M output to your mixing console or mic preamp. Connect

the second channel following the same steps.

Radial Engineering Ltd. Radial Engineering Ltd. Radial Engineering Ltd.

SB-48®Phantom Supply SB-48®Phantom Supply SB-48®Phantom Supply

CONNECT THE POWER

Afterthe audio connections aremade you can connectthe included

15V/400mAAC/DC power adapter to the SB-48’s power jack. The

power LED illuminates when the SB-48 is active. Turn your audio

system on and test the mic signals at a low volume to ensure the

system is properly connected and the microphones are working.

USING THE CABLE CLAMP

Ahandy cableclamp locatednext tothe powerjack canbe employed

to prevent accidental power disconnection. Use a hex driver to

loosen the cable clamp’s screw a few turns until the cable can be

looped through the clamp and re-tighten.

USING THE 12/48V SWITCH

You can set the phantom power voltage to 12 volts using the

recessed 48/12V switch on the side of the SB-48. Use a small

screwdriver to access the switch. When the switch is in the outward

position the SB-48 will supply 48 volts of phantom power. When set

to the inward position it will supply the mic with 12 volts.

Indice

Altri manuali Radial Engineering Alimentazione elettrica

Radial Engineering

Radial Engineering SB-48UB Manuale utente

Manuali Alimentazione elettrica popolari di altre marche

Monacor

Monacor PS-12CCD Manuale utente

VOLTIMA

VOLTIMA MagicBox 15 Manuale utente

Agilent Technologies

Agilent Technologies 6032A Manuale utente

Miller

Miller Auto Deltaweld 452 Manuale utente

BCP

BCP PUOUBK Foglio di istruzioni

HC 2210 Manuale utente

Puls

Puls CT5.241 Manuale utente

OCZ

OCZ ZX1250W Manuale utente

iseg

iseg ECH 238 Manuale utente

Power

Power XXL A Series Manuale utente

Agilent Technologies

Agilent Technologies 6631B Manuale utente

Renogy

Renogy PHOENIX 300 Manuale utente

HP 6200B Manuale di servizio

Epson

Epson Stylus Scan 2500 Manuale operativo

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Manuale utente

Puls

Puls MiniLine ML50.100 Manuale utente

Puls

Puls AS-Interface SLA4.100 Manuale utente

Kenwood

Kenwood PS-60 Manuale utente