Raidon SL3610-2S-LB2 Manuale utente
NAS
SL3610/20-2S-LB2
Quick Installation Guide
v.1.0 (September, 2009)
A. Product Diagrams and Contents of Product Package
SL3610-2S-LB2
Front View
Rear View
The indicator on the left will light on green when Gigabit LAN Port is connected to Gigabit LAN and the
indicator on the right will light on orange when Host Access is enabled.
MUTE
ALARM
ESC
ENT
HDD 0
HDD 1
Key Insertion
Opening
Access LED
Tray Handle
LCD buttons
LCD screen
Gigabit LAN
Port
USB2.0 Port
Fan
2
SL3620-2S-LB2
Front View
Rear View
1. The indicator on the left will light on green when Gigabit LAN Port is connected to Gigabit LAN and
the indicator on the right will light on orange when Host Access is enabled.
2. With startup completed, press and hold the “Reset” key for 5 seconds and the system will be reset to
default settings.
HDD 0
HDD 1
Status LED
Key Insertion
Opening
Access LED
Tray Handle
Gigabit LAN
Port
USB2.0 Port
Fan
Reset
3
Contents of Product Package
Item Quantity
NAS Device 1
AC Power Cable 1
Gbit 2M Cable 1
Quick installation Guide 1
CD (User Guide) 1
Accessory Kit 1
Please make sure that related accessories and the product body are not damaged or missing. If you
have any questions, contact the distributor or sales.
B. Precautions Before Application
1. We suggest you to use 2 brand new 3.5-inch SATA hard drives with the same brand and model
number.
2.If you want to use two used hard drives on RAIDON NAS, please transfer your data on other hard
drives in case the data loss caused by setting.
3. The factory default value of this product is RAID 1 with fault tolerance which can survive as one hard
drive is failed. If RAIDON NAS is considered as an extra storage, please change the setting to
RAID 0 mode. Please be note that change the RAID mode after starting using the device will
cause data loss.
4. You can use four setting buttons at the right side of the LCD display to set the device. Please refer to
the user manual for the detail information.
C. Hardware Installation
Step 1: Take out the tray and install your hard disk in it. Make sure to fasten the hard disk securing
screws to prevent damages caused by unnecessary movement.
4
Step 2: Once the installation is completed, insert the tray back and x it rmly in the proper place.
Step 3: Connect the Gigabit LAN port and, nally, connect the power cord.
Step 4: Hardware installation is completed. You can power on the system to start the related setup and
application. Please refer to the user manual for detail information.
D. Setup Utility (Windows Only)
1. Select “Setup Utility” from GUI Utility / NAS in the attached CD (User Guide) and you can see the
following screen. Click Setup and enter the install process.
Notice : “Setup Utility” is only suitable for Windows operating system. For other operating systems, please refer
to “2.3 Initial Setup” in the user manual for the information about network setting.
2. “RAIDON NAS” will be shown in the left column, and the related setting details will be shown at the
right side. Select “RAIDON NAS” in the left column and click “OK”. If “RAIDON NAS” is not shown
in the column, please click “Search again” to search the device until it appears. (The system will take
about 2 minutes to nd the device.
5
3. Enter the password. (Default password: admin)
4. Select “ Obtain an IP address” and then click “Next” to proceed.
5. Set Date and Time by your time zone and then click “Next” to proceed.
6
6. Make sure all settings details are right and click “Save” to conrm. The setting process will go back
to the step 1. You will see all setting details at the right side.
E. Start RAIDON NAS
1. Input IP address on the browser.
Please input the IP address shown on the setup utility and press enter. The following screen will be
shown up.
Input the username and password. Then click “Login”.
(Default username : admin / password : admin)
7
2. The System Information screen will show the new installed hard drives.
Please format the hard drives rst, and then proceed to the following process.
3. Click “Maintenance / RAID Setting” and see the Disk Status at the right side.
Please select RAID level as your need and click “Create Raid System” to build up the system.
4. The system will format the disks and all data saved on the disks will be cleared. Please click “OK” to
start the process.
8
5. Creating RAID System
6. The system will reboot while the RAID system is built up. It takes about 3 minutes to reboot. After
nish, please login again.
7.Input username and password.
Default user name: admin
Default password: admin
9
8.After login, you can see the system information.
F. Quick Setup
Please select “Quick Setup / Wizard” at the left side to start the quick setup process.
10
Altri manuali per SL3610-2S-LB2
1
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Raidon Hardware per computer
Raidon
Raidon InTANK iR2301 Manuale utente
Raidon
Raidon SAFETank Series Manuale utente
Raidon
Raidon InTANK iR2822 Manuale utente
Raidon
Raidon SafeTANK GR3680-SB3 Manuale utente
Raidon
Raidon InTANK iR2022S Manuale utente
Raidon
Raidon iT4300 Series Manuale utente
Raidon
Raidon SafeTANK GR5630-SB3 Manuale utente
Raidon
Raidon iU1776-U6P3 Manuale utente
Raidon
Raidon iT2300 Manuale utente
Raidon
Raidon iR2970 Manuale utente
Manuali Hardware per computer popolari di altre marche
EMC2
EMC2 VNX Series Manuale del proprietario
Panasonic
Panasonic DV0PM20105 Manuale utente
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manuale utente
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manuale utente
National Instruments
National Instruments PXI-8186 Manuale utente
Hauppauge
Hauppauge WinTV-HVR-2250 Manuale utente
