RC Lander T-33 Guida rapida
RCLander T-33
OPERATIONAL MANUAL
- 2 -
Please read before operating this system!
W
e would like thank you for purchasing our new product T-33,
designed for the hobby enthusiast. Based on its full - scale
counterpart, this USA Jet can undertake loops, inverted flight, rolls
and other aerobatics easily. It is a highly maneuverable model aimed
at the intermediate to expert pilot. With the T-33 model which
includes EDF set*, speed controller, electric servo, flaps, metal
electric retractable landing gear & scale suspension struts with front
steering, full scale functional g ar doors system & air-brake system.
You will have joyful time in model flying.
Remarks:*
We have metal EDF set for your selection.
1) LEDFDPS90-1A13 is a higher grade EDF set which is an
aluminum alloy material EDF offering a powerful output without
compromising efficiency and durability.
2) Please be aware that although all servos have been pre-set to the
center point at our factory there may be discrepancies due to
different radio manufacturers . Please make sure that you check
the centre point with your own radio before installing of the model.
4) Centre of Gravity for this model is measured 120mm (+ 5mm)
from main wing leading edge to centre direction.
5) Please make sure to use a little piece of velco or strong foam
double tape (not included) to secure your LiPo battery before
flying.
- 3 -
Specifications:
Wing Span :
1683mm
Length:
1520mm
AUW:
3.7kg
up
EDF(Lander Metal DPS EDF):
90mm
Power:
9S 4500mAh 25C or above
Thrust:
Up to 3.96kg
Function:
Flaps system-included
Metal Electric retract & scale suspension struts included
Gear doors system & Air-Brake (Option)
ESC:
100A or above
EDF SYSTEM
L
LL
LEDF
EDFEDF
EDFDPS
DPSDPS
DPS90
9090
90-
--
-1A
1A1A
1A13/9
13/913/9
13/9
Material:
Aluminum Alloy, Metal special
Weight:
Ca. 538g(Motor included)
Rotor:
90mm dia, 5-bladed.
Max rpm
42,000 rpm
Application:
2508W
Staic Thrust:
3.96kg
Main Accessories
- 4 -
Main Fuselage Front Lower Fuselage Both side of Inlet Parts
Inside Ducting plate Parts Upper Rear Fuselage Lower Rear Fuselage
Both Side Main Wing Set Horizontal Stabilizer Vertical Stabilizer
Canopy 90 & 120 EDF Bay Parts Both Side Fuel Tanks
- 5 -
Bombs& Missiles Parts PVC Wheel Cups parts PVC Gear Doors Parts
PVC Air-Brake Set Plywood Block Set
Remarks: 1) Operational Manual (included)
2) Extension cord x 7pcs & Y cord x 6pcs (included) except ARF version
3) Push rods for Elevator, Rudder, Aileron, Flaps, Air-Brake & Front Steering (included)
5) One plastic bag includes screws, Control Horns, Linkage Stoppers & related plywood block
set.
- 6 -
Assembling the aircraft.
For color images please go to www.rclander.com for
download.
01
1) Take one extension cord to connect the
nose electric retract first.
2) The nose electric retract has been
pre-installed by factory before
shipment.
02
1）Suggest to find one piece 70-130mm
anti-slip foam plate (not included) for the
battery compartment.
03
1) Using the strong double tape to fit on the
anti-slip foam plate on the battery
compartment as shown. Then put on the
nose gear extension cord well.
.
- 7 -
04
1) Use your Radio to gear down the nose
gear first for preparation to glue up the front
lower fuselage on the main fuselage.
05
1) Take enough epoxy to glue up the lower
front fuselage on the main fuselage.
06
1) After finished the fixing of lower front
fuselage, keep on the install the inside
ducting plate.
2) Pls glue up the both side ducting plates
together first.
- 8 -
07
1)According to the inside slot of main
fuselage to take some epoxy to glue up the
inside ducting plate set on the right position.
08
1) After glued up the inside ducting plate,
pls cut out the cross foam bar as shown.
09
1) Prepare to install both side inlet parts on
the main fuselage
- 9 -
10
1) Inside the main fuselage is already pre
set some slot for fitting both of two side
inlet parts.
2) Kindly use the enough the epoxy and
work carefully to install the inlet parts
one by one as shown. It is because glue
up area so longer.
11
1) Glue up both side inlet parts on the main
fuselage should be one by one procedure.
12
1)Install the both side guiding inlet air plates
- 10 -
13
1) Make sure the guiding inlet plate to be
able fitted on the right position before
glue up. Pls be reminded the shorter
side is out & longer side is in side.
2) The installing method is put it from
inside to outside.
14
1) After confirm the guiding inlet plate on
the right position that can be used some
epoxy to glue up as shown.
15
1) Prepare to install the horizontal &
vertical stabilizer on the upper rear main
fuselage.
2) Pls install the related servos before glue
up action.
Indice
Altri manuali RC Lander Giocattolo
